Review all available part information (MPN, package, pin count, description, properties). If no datasheet URL is already set, search the web for the official datasheet and update the part's Datasheet property with the URL. Then cross-check the schematic symbol, footprint, and pin descriptions against the datasheet. Summarize key specs and flag any mismatches.
I’ll review the part metadata, find and attach the official datasheet if needed, then cross-check the symbol, footprint, and pin descriptions against it and summarize any mismatches.
Remote On/Off: On = 3–12 VDC or open; Off = 0–1.2 VDC or short to –Vin
Recommended input fuse: 6.3 A slow-blow for 24 V input models
Datasheet pinout — single-output model
Table
Pin
Datasheet function
Symbol terminal present?
Symbol terminal name
1
+Vin / Vcc
Yes
+VIN_(VCC)
2
–Vin / GND
Yes
-VIN_(GND)
3
Remote On/Off
Yes
REMOTE_ON/OFF
4
+Vout
Yes
+VOUT_1
5
–Vout
Yes
-VOUT_1
6
Trim
Yes
TRIM
Symbol review
Matches
Symbol exposes the correct six terminals for the single-output TEN 30-2411WIN.
Pin numbers match the datasheet single-output pinout:
Pin 1 = +Vin / Vcc
Pin 2 = –Vin / GND
Pin 3 = Remote On/Off
Pin 4 = +Vout
Pin 5 = –Vout
Pin 6 = Trim
Mismatches / cleanup items
All six terminal components have Pin Type = Unspecified. Recommended assignments:
Pin 1 +VIN_(VCC): Power input
Pin 2 -VIN_(GND): Power input / ground return
Pin 3 REMOTE_ON/OFF: Input / control
Pin 4 +VOUT_1: Power output
Pin 5 -VOUT_1: Power output return
Pin 6 TRIM: Passive/analog trim input or unspecified if Flux pin typing is intentionally conservative
Terminal names include underscores and suffix _1 on output pins. This is not electrically wrong, but the part symbol would be cleaner as +VIN, -VIN, REMOTE ON/OFF, +VOUT, -VOUT, TRIM.
Footprint and mechanical review
Datasheet mechanical/footprint data
Body: 50.8 mm × 25.4 mm × 10.2 mm
Pin length below case: 5.6 mm
Pin diameter: 1.0 ±0.1 mm
Through-hole footprint, 6 pins
Row spacing along package length: 45.72 mm
Top row spacings: pin 3 → pin 2 = 15.24 mm; pin 2 → pin 1 = 5.08 mm
Practical derived bottom-view coordinates from datasheet drawing:
Pin 3: x 2.54 mm, y 2.54 mm
Pin 2: x 17.78 mm, y 2.54 mm
Pin 1: x 22.86 mm, y 2.54 mm
Pin 6: x 2.54 mm, y 48.26 mm
Pin 5: x 12.70 mm, y 48.26 mm
Pin 4: x 22.86 mm, y 48.26 mm
Current footprint observed in Flux
Six pads exist, one for each symbol terminal.
Pad coordinates appear scaled in meters while labelled as mm in the layout output; the relative coordinates correspond to:
Pin 1: x 0 mm, y 0 mm
Pin 2: x -5.08 mm, y 0 mm
Pin 3: x -15.24 mm, y 0 mm
Pin 4: x +2.54 mm, y 45.72 mm
Pin 5: x -7.62 mm, y 45.72 mm
Pin 6: x -17.78 mm, y 45.72 mm
These relative spacings match the datasheet pattern:
Pin 3 → pin 2 = 15.24 mm
Pin 2 → pin 1 = 5.08 mm
Pin 6 → pin 5 = 10.16 mm
Pin 5 → pin 4 = 10.16 mm
Row spacing = 45.72 mm
Silkscreen/fab outline appears approximately 25.4 mm × 50.8 mm with margin, matching the 2" × 1" package.
Footprint mismatches / risks
Critical: Pad size is reported as 0.00195 in the layout output. If interpreted as mm, this is far too small for 1.0 ±0.1 mm through-hole pins. It likely represents a unit scaling artifact, but this must be verified in the footprint editor. A practical finished hole should clear a 1.0 mm pin, typically around 1.2–1.4 mm drill with appropriate annular ring depending on manufacturing rules.
The pads are on Top with forceAnnularLayers: Top, Bottom, which suggests through-hole behavior, but there is no explicit drill/hole diameter visible in the inspected rules. Verify that these pads are actual plated through-holes and not just SMD circular pads.
The footprint orientation appears consistent with datasheet bottom-view spacings, but orientation should be verified visually against the bottom-view numbering before publishing/using in a board.
Overall verdict
The symbol pin count and pin-number/function mapping match the TEN 30-2411WIN datasheet. The footprint relative pad spacing and outline dimensions also match the datasheet mechanically. The main issues to address are pin type metadata, terminal naming cleanup, and verification/correction of through-hole pad drill/diameter data for the 1.0 mm pins.