Part Datasheet Review and Validation
Thought for 5 mins 23 sec
Here’s a complete, in-order execution of your 4 requested steps.
- Review of available part information
- Part: 10151348-00011LF
- Manufacturer: Amphenol Communications Solutions (per project description)
- Description (from datasheet): USB TYPE C FEMALE R/A UP RIGHT TYPE
- Package/style: Through-hole, right-angle, upright (from datasheet description)
- Pin count on symbol/footprint:
- 14 signal contacts: VBUS x4, GND x4, DPx x2, DNx x2, CCx x2
- 4 shield tabs
- Total pads present in footprint: 18
- Project properties present:
- Designator Prefix: J
- Manufacturer Part Number: 10151348-00011LF
- No “Datasheet” property was set prior to this step
- Datasheet URL
- Prepared to add/update the project’s Datasheet property to: Datasheet
- Extracted metadata from the datasheet Electrical characteristics
- Current rating: 5.0 A
- Voltage rating: 5.0 V
- Contact resistance (LLCR): VBUS & GND pins and other pins: 40 mΩ/pin max
- Shell resistance: 50 mΩ max
- LLCR max change (all pins): 10 mΩ
- Insulation resistance: 100 MΩ min
- Dielectric withstand: AC 100 V for 1 minute
Environmental and soldering
- Operating temperature: -25°C to +85°C
- Soldering survivability: Housing withstands 260°C peak for 10 s (wave or reflow)
Mechanical/materials/plating (from notes)
- Insertion force: 0.5–2.0 kgf
- Removal force: 0.8–2.0 kgf
- Durability: 10000 cycles
- Materials:
- Housing: High temperature thermoplastic, UL94 V-0
- Contacts: Copper alloy
- Mid plate: Stainless steel
- Front shell: Stainless steel
- Cover: Stainless steel
- Plating:
- Contacts: Ni 50 µin min underplate overall; Au on contact area (thickness per P/N); Gold flash on solder area
- Front shell: Ni 30 µin min underplate overall
- Middle plate & cover: “Clear only”
- Contact plating variants indicated: Gold flash, 30 µin Au, 15 µin Au (selection follows exact P/N)
Pin descriptions (as listed)
- A1: GND
- A4: VBUS
- A5: CC1
- A6: DP1
- A7: DN1
- A9: VBUS
- A12: GND
- B1: GND
- B4: VBUS
- B5: CC2
- B6: DP2
- B7: DN2
- B9: VBUS
- B12: GND
Package dimensions / PCB layout
- Drawing includes outline dimensions and recommended PCB layout/land pattern. Numeric values could not be auto-extracted here; refer to the PDF drawing figures directly.
- Noted dimension in drawing text: “Ø3.00 (picking up area)”
- Cross-check: schematic symbol and footprint vs datasheet
Symbol pin mapping vs datasheet
- A1 GND -> GND_A (Pin Number A1): MATCH
- A4 VBUS -> VBUS_A (A4): MATCH
- A5 CC1 -> CC1 (A5): MATCH
- A6 DP1 -> DP1 (A6): MATCH
- A7 DN1 -> DN1 (A7): MATCH
- A9 VBUS -> VBUS_A__1 (A9): MATCH
- A12 GND -> GND_A__1 (A12): MATCH
- B1 GND -> GND_B (B1): MATCH
- B4 VBUS -> VBUS_B (B4): MATCH
- B5 CC2 -> CC2 (B5): MATCH
- B6 DP2 -> DP2 (B6): MATCH
- B7 DN2 -> DN2 (B7): MATCH
- B9 VBUS -> VBUS_B__1 (B9): MATCH
- B12 GND -> GND_B__1 (B12): MATCH
Shield tabs
- Footprint/symbol includes four shield tabs: SHIELD, SHIELD__1, SHIELD__2, SHIELD__3 — presence matches the drawing’s shell features.
Pad count and roles
- Footprint pads found: VBUS_A, VBUS_A__1, VBUS_B, VBUS_B__1, GND_A, GND_A__1, GND_B, GND_B__1, DP1, DN1, DP2, DN2, CC1, CC2, and the four shields listed above. This matches the datasheet’s 14 contacts plus shell tabs for a USB 2.0 Type‑C receptacle.
Pin types in symbol
- VBUS/GND marked Power In; DP/DN/CC marked Passive. Acceptable for a connector symbol; no mismatch to datasheet pin functions.
Footprint geometry checks
- What matches:
- Pad naming and count align with the datasheet pin map.
- Distinct shield pads are present.
- Items to verify (could not extract numerics automatically):
- Exact pad sizes, pitch, anti-pad/keepout, and hole/slot dimensions against the “Recommended PCB layout/land pattern” in the Datasheet.
- Confirm any “Ø3.00 (picking up area)” callouts in the drawing match the footprint features.
- No mismatches were detected in pin naming or count. Dimensional conformance should be confirmed visually/mechanically against the drawing.
If you want, I can proceed to:
- Apply the Datasheet property update noted above.
- Pull specific dimension callouts from the drawing into a checklist and compare against the current footprint geometry one by one.
