Part Review and Datasheet Verification
Thought for 7 sec
I’ll inspect the part metadata, find and set the official datasheet if missing, then verify symbol/footprint/pins against the datasheet and summarize any discrepancies.
Thought for 30 sec
The part already has an official Molex Datasheet URL set, so I’m using that for verification rather than replacing it.
Worked for 4 mins 16 sec
Completed the part review for Molex 395933008. The Datasheet URL was already set to the official Molex URL, so I left it unchanged.
Key findings are saved in Part Review: Molex 395933008. Main mismatch: the symbol has 16 terminal entries with pins 1–8 duplicated across two sub-symbol sections, while the datasheet defines an 8-circuit connector; pin descriptions and several useful rating/spec properties are also missing.
Suggested next steps:
- Remove/resolve the duplicate symbol terminals.
- Add pin descriptions for terminals 1–8.
- Add connector spec properties like pitch, current, voltage, wire size, and temperature.
- Manually verify footprint drill/pad geometry against the Molex drawing.
Fix symbol and verify
Fix duplicate terminals
Add connector properties
Verify footprint geometry
Run ERC DRC
Refine this doc
Ask about this doc
Part Review: Molex 395933008
Reviewed source
- Project:
adrian95/395933008 - Part UID:
2ec3eb36-fa6e-4398-846f-ff6446e751d8 - Manufacturer: Molex
- MPN:
395933008/ searchable Molex format39593-3008,0395933008 - Datasheet URL currently set: https://www.molex.com/en-us/products/part-detail-pdf/395933008?display=pdf
- Datasheet source used: Molex official product/datasheet content. The web scraper had limited PDF-body access, but the datasheet query extracted Molex product metadata and specifications.
Key official specs found
- Description: 5.00 mm pitch Eurostyle vertical fixed-mount PCB terminal block, green housing, 8 circuits
- Product family/name: Eurostyle Fixed Mount
- Type: PCB terminal blocks and connectors
- Application: wire-to-board
- Component type: one-piece
- Circuits loaded / maximum: 8 / 8
- Rows: 1
- Pitch: 5.00 mm mating interface, 5.00 mm termination interface
- Orientation: vertical
- Entry angle: horizontal
- Mounting: PCB fixed mount; panel mount: no
- Recommended PCB thickness: 2.00 mm
- PC tail length: 3.00 mm
- Wire size: 14, 16, 18, 20, 22 AWG; 0.33–2.08 mm²
- Current maximum per contact: 15 A
- Voltage maximum: 300 V
- Operating temperature: -40 °C to +105 °C
- Color: green
- Stackable: no
- Lock to mating part: no
Project metadata review
Present:
- Datasheet URL: official Molex PDF/product-detail URL is already set.
- Manufacturer Name: Molex
- Manufacturer Part Number: 395933008
- Designator Prefix: J
Missing or incomplete:
- No explicit project/component properties found for connector pitch, positions/circuits, rows, voltage rating, current rating, wire size, operating temperature, orientation, PCB thickness, or tail length.
- Description exists at project level but is sparse and does not include the full Molex description.
Schematic symbol review
Observed schematic terminal objects:
- 16 terminal components are present, but the datasheet defines 8 physical circuits/pins.
- Pin numbers 1 through 8 each appear twice, once in sub-symbol suffix
395933008_1_1and once in395933008_1_2. - Terminal Pin Type is
Unspecifiedfor all terminals. - No Pin Description properties were found.
- Pins show as
undefinedin the schematic inspection output.
Assessment:
- Mismatch: the symbol duplicates every physical pin across two sub-symbol sections. For an 8-circuit terminal block, each physical terminal should appear once unless the duplicate symbol sections are intentionally alternate views/jumpers; nothing in the datasheet supports duplicate electrical terminals.
- Mismatch/incomplete: pin descriptions are missing. Suggested descriptions are generic terminal names such as
Terminal 1throughTerminal 8. - Incomplete: pin type should likely be passive/unspecified terminal style;
Unspecifiedis acceptable electrically but less descriptive.
Footprint review
Observed footprint/layout nodes:
- Footprint contains pads numbered 1 through 8.
- Pad count matches the datasheet circuit count of 8.
- Silk/fab outline appears approximately 40.0 mm wide by 10.0 mm deep, consistent with an 8-position 5.00 mm pitch connector body scale.
- Pad/pin pitch from visible footprint extent appears consistent with 5.00 mm spacing across 8 positions, but detailed pad drill/diameter values were not exposed by the layout inspection output.
Assessment:
- Pad count appears correct.
- Footprint mechanical verification is partial because detailed pad geometry/drill information was not available in the inspection output and the scraped PDF did not expose the drawing table.
- Recommended follow-up: verify pad drill/finished-hole diameter and courtyard/body outline directly against the Molex drawing.
Flagged mismatches / risks
- Symbol pin duplication: 16 schematic terminals for an 8-circuit part; pins 1–8 are duplicated across two sub-symbol suffixes.
- Missing pin descriptions: no Pin Description properties for terminals 1–8.
- Incomplete properties: key connector/electrical specs are absent from the part properties even though they are available from Molex.
- Partial footprint geometry verification: pad count and broad outline look correct, but drill/pad dimensions could not be fully checked from available tool output.
Recommended fixes
- Remove the duplicate sub-symbol terminals so each physical pin 1–8 appears once, or confirm the duplicate sections are intentionally alternate symbol views before publishing.
- Add Pin Description values:
Terminal 1throughTerminal 8. - Add useful component/project properties: Connector Pitch = 5.00 mm, Connector Positions = 8, Connector Rows = 1, Voltage Rating = 300 V, Current Rating = 15 A/contact, Operating Temperature = -40 to +105 °C, Wire Size = 14–22 AWG / 0.33–2.08 mm², Orientation = Vertical, PCB Thickness Recommended = 2.00 mm, PC Tail Length = 3.00 mm.
- Verify footprint drill and pad dimensions manually against the Molex drawing or with a layout export that exposes pad geometry.
Welcome 👋
Flux accelerates your PCB design with AI.
Create your account to start using this component and bring your ideas to life.