ESP32-C3 RGB Board

P

pnielsen

The transistors will sink the existing 5V feed.
P

pnielsen

But 3.3V should be taken from a 29V feedd

flux

Understood—corrected architecture: 29 V only powers the controller’s 3.3 V rail, while the existing external 5 V feed passes to the LED rope and the SI2310s sink its R/G/B channels. The board will not generate or regulate LED power; the 29 V and 5 V systems must share ground for the open-drain controls and MOSFETs.

flux

The architecture is now correctly defined as:
  • 29 V DC → controller power only, regulated down to 3.3 V for the ESP32.
  • Existing external 5 V passes directly through from the input RGB connector to the LED-rope connector.
  • SI2310 MOSFETs sink the rope’s R/G/B channels.
  • External R/G/B inputs remain active-low, open-drain signals.
  • The 29 V supply ground, external 5 V source ground, MOSFET sources, and logic ground must be common.
Already completed before this correction:
  • TMUX4053 source-selection circuit
  • Open-drain input conditioning
  • Three MCC SI2310-TP MOSFET stages
  • Two JST-PH 4-pin, 2.0 mm RGB connectors
  • 30 × 30 mm four-layer board outline
The final 29 V-to-3.3 V regulator redesign and resulting placement were dispatched, but I could not inspect or verify the completed result. The last verified placement was still too congested for a credible routed 30 × 30 mm board.
Execution stopped because your ACUs ran out.
Inspect regulator redesign
Review power architecture
Check placement congestion
Calculate power budget
Check ERC and DRC
Sign up to send

Files

Schematic

Layout

3D View

Do we need to use usb to uart bridge in this project
U

serkank

@copilot Do we need to use usb to uart bridge in this project
2y

copilot

Based on the provided schematic description, it doesn't appear that a USB to UART bridge is being used. The ESP32-C3-WROOM-02 module integrates a UART interface and this UART interface is directly connected to the USB Type-C connector (J1).
Here are the reasons why it might not be necessary to use a UART bridge in this design:
  • The ESP32-C3-WROOM-02 has a built-in UART interface.
  • The UART interface is wired directly to a USB Type-C connector (J1), which likely connects to a host computer for debugging or programming the device.
To confirm, please check these specific connections:
  • U1 (ESP32 module) IO19 pin (TXD) is connected to USB Type-C DP pins.
  • U1 (ESP32 module) RXD pin is connected to USB Type-C DM pins.
However, in some cases a USB to UART bridge might be inserted between the Micro-USB/USB-C connector and the ESP32's UART lines to handle voltage level conversions or for other reasons. If you feel a USB to UART bridge is needed based on your project requirements, it's recommended to add it to the schematic.
2y
Someone is typing...
3
explain this project.
U

serkank

@copilot explain this project.
2y

copilot

This is an IoT reference design project making use of the ESP32-C3-WROOM-02 module, manufactured by Espressif Systems. The ESP32-C3-WROOM-02 is a powerful WiFi module encased with SoC with an integrated microcontroller, RAM, flash memory, and features like GPIO, SPI, I2C, and UART.
Several other notable components are included in the design as well:
  • A USB C connector (Designator: J1), likely for power supply as well as firmware/flashing the ESP module.
  • Two 10-pin connectors (Designators: J2, J3) which appear to bring out various I/O lines from the ESP32-C3-WROOM-02 and potentially for added functionality or modularity. The exact usage might depend on specific application requirements.
  • Two tactile switches (Designators: SW1, SW2) likely for user input or system control, possibly for controlling boot mode or reset function of the ESP module.
  • An RGB LED (Designator: LED1), likely used for status indication.
  • A voltage regulator (Designator: IC1). This is a TPS62130RGTR step-down converter from Texas Instruments, used to step down the input voltage to suit the working voltage of the ESP32-C3-WROOM-02.
  • There are several passive components like resistors (R1 through R10) and capacitors (C1 through C6). These could be for a variety of purposes – buffering power supply, setting voltage levels, noise filtering, etc.
  • There's also an inductor (Designator: L1) which is generally used in conjunction with the voltage regulator for smoothing out the output.
The schematic also includes several virtual components representing nets and power rails for providing power and signals to various parts of the circuit. The exact purpose and functionality of these components will depend on the nature of the overall design and the specific pin mapping of the ESP32-C3-WROOM-02. The design project is licensed under Creative Commons (CC BY 4.0).
2y
Someone is typing...
2
when programing with USB should ESP\_BOOT be pulled low via SW1?
U

gabrielcordeiroz

@copilot when programing with USB should ESP_BOOT be pulled low via SW1?
1y

copilot

Yes, when programming the ESP32-C3-WROOM-02 via USB, the ESP_BOOT pin needs to be pulled low to put the ESP32 into bootloader mode. This is commonly done using a switch like SW1.
To achieve this, you can connect SW1 so that pressing it connects the ESP_BOOT signal to ground. Here’s how you can wire it:
Releasing the switch should disconnect the ESP_BOOT pin from ground, allowing the ESP32 to boot normally. This setup allows you to manually put the ESP32 into bootloader mode by holding the switch when powering up or resetting the device.
1y
Someone is typing...
4
U1
J1
C1
Capacitance
3.3nF
J3
C4
Capacitance
10uF
C3
Capacitance
22uF
J2
C6
Capacitance
1uF
C2
Capacitance
10uF
C5
Capacitance
0.1uF
SW1
SW2
R8
Resistance
220 Ω
R1
Resistance
Resistance
R3
Resistance
5.1KΩ
R4
Resistance
Resistance
R5
Resistance
100KΩ
L1
Inductance
2.2uH
LED1
R6
Resistance
220 Ω
IC1
R7
Resistance
220 Ω
R2
Resistance
5.1KΩ
R10
Resistance
10KΩ
R9
Resistance
10KΩ
No files yet