BSS138 vs 2N7002 Comparison


I’ll read the attached text to see what you’d like me to do.
I verified both pinouts and the manufacturer-specific electrical data. I’ll compare the hosted onsemi BSS138 with Nexperia’s unsuffixed 2N7002, and flag differences in test current rather than treating the resistance ratings as identical tests. The brief’s “Related in Flux” URLs point to unrelated LEDs; I’ll use the BSS138 guide and 2N7002 links supplied earlier in the brief.
Created a project doc

BSS138 vs 2N7002: Differences and Which to Use

View Document

BSS138 vs 2N7002: Differences and Which to Use
BSS138 vs 2N7002: BSS138 has a lower specified threshold, while the compared 2N7002 has a higher drain-voltage rating. Choose BSS138 for an already-qualified low-drive circuit; choose the compared 2N7002 for additional voltage margin after checking drive and loss requirements.
This comparison uses the project's onsemi BSS138, without an electrical suffix, in SOT-23-3, and Nexperia 2N7002, without an electrical suffix, in SOT23 (TO-236AB). It does not combine ratings from other manufacturers, enhanced suffix variants, dual devices, or level-shifter modules. The threshold and voltage differences in the opening refer only to these selected devices and the condi...
Created and checked BSS138 vs 2N7002: Differences and Which to Use in project files. No existing files were edited or deleted.
Left out:
  • Current, power, and thermal-rating comparisons: a matched-condition comparison was not established.
  • Gate charge, switching times, and numeric land-pattern dimensions: not fully verified for both selected parts.
  • Measurement pulse widths/duty cycles and the ,215 packing-code details: not established in the queried Nexperia datasheet.
  • Prices and stock, as requested.
Pinout risk: the selected variants are pin-compatible, but that does not guarantee electrical interchangeability. The guide requires footprint/orientation checks and application requalification.
I also replaced the brief’s unrelated LED links with the intended guide and transistor links.

Last modified 1mo ago

BSS138 Application and Usage Guide
The onsemi BSS138 is a 50 V N-channel enhancement-mode MOSFET in a 3-lead SOT-23 package, commonly used for bidirectional open-drain I2C level translation as well as low-current switching. Its low threshold voltage indicates the onset of conduction, not a fully on state; use guaranteed on-resistance conditions and thermal limits when estimating load capability.
1. Quick Specifications

Table


ParameterValueRating classConditions / engineering meaning
Drain-source voltage, VDSS50 VAbsolute maximumMaximum drain-to-source stress; do not design normal operation at this limit.
Gate-source voltage, VGSS±20 VAbsolute maximumMaximum gate-to-source stress.
Continuous drain current, ID0.22 AAbsolute maximumDatasheet Note 1 thermal mounting condition; not a universally available continuous current.
Pulsed drain current, IDM0.88 AAbsolute maximumPulsed rating under Note 1; pulse width, duty cycle, SOA, and junction temperature still apply.
Power dissipation, PD0.36 W at TA = 25 °CAbsolute maximumMinimum-pad thermal condition; derate 2.8 mW/°C above 25 °C.
Junction/storage temperature−55 to +150 °CAbsolute maximumTJ and TSTG range.
RθJA350 °C/WCharacterized thermal conditionMounted on a minimum pad; actual PCB copper and airflow change thermal performance.
VGS(th)0.8 V min, 1.3 V typ, 1.5 V maxCharacterized thresholdVDS = VGS, ID = 1 mA, TA = 25 °C; this is not a low-resistance drive point.
RDS(on), 10 V drive0.7 Ω typ, 3.5 Ω maxGuaranteed electrical characteristicVGS = 10 V, ID = 0.22 A, TA = 25 °C.
RDS(on), 4.5 V drive1.0 Ω typ, 6.0 Ω maxGuaranteed electrical characteristicVGS = 4.5 V, ID = 0.22 A, TA = 25 °C.
3.3 V gate operationNo guaranteed RDS(on) pointCharacterized/conditionalTypical curves may be informative, but validate voltage drop and temperature or select a MOSFET guaranteed at 2.5 V/3.0 V.
PackageSOT-23-3, onsemi Case 318-08PhysicalThree-lead surface-mount package.
Same-side lead pitch1.90 mm nominalPhysicalDimension e between the two leads on the same package side: 1.78 mm min, 1.90 mm nominal, 2.04 mm max; this is not a universal adjacent-pin pitch.
These are component limits, not recommended operating setpoints. Apply voltage, current, power, and temperature margin appropriate to the product environment.
2. Pinout & Connections

Table


Pin NumberPin NameDescriptionBest Practice
1Gate (G)Voltage-controlled input.Keep the gate trace short, add a pull-down when the controller can float, and keep VGS within the ±20 V absolute maximum.
2Source (S)Low-side/reference terminal in low-side switching and low-voltage bus terminal in the discrete I2C translator.Route directly to the local return for switching, or to the low-voltage open-drain bus for translation.
3Drain (D)Load terminal in low-side switching and high-voltage bus terminal in the discrete I2C translator.Check body-diode orientation and keep drain stress below a suitably derated value from the 50 V absolute maximum.
3. Standard Application Circuit
Bidirectional open-drain I2C level translation
Use one BSS138 per open-drain line: one channel for SDA and one for SCL. The following table is the complete connection recipe; signal nodes are not tied directly to either supply.

Table


NodeConnections
GateTie directly to the low-voltage supply, VLOW.
SourceConnect to the low-voltage SDA or SCL signal node.
DrainConnect to the corresponding high-voltage SDA or SCL signal node.
Low-side pull-upConnect one resistor from the source-side signal node to VLOW.
High-side pull-upConnect one resistor from the drain-side signal node to VHIGH.
GroundConnect both voltage domains to a common ground; this circuit is not galvanically isolated.
The source-low/drain-high orientation is specified by NXP’s discrete bidirectional I2C translator application note.AN10441 primary application source Both sides must behave as open-drain/open-collector signals, or otherwise be controlled to prevent a HIGH driver from contending with a LOW driver; passive pull-ups establish each side’s logic-high voltage.AN10145 open-drain and pull-up guidance
With both buses high, gate and source are near VLOW, so the channel is off and each bus reaches its own pull-up rail. A LOW driven on the low side produces positive VGS and turns the MOSFET on. A LOW driven on the high side initially conducts through the intrinsic body diode, lowering the source until VGS turns the channel on and transfers the LOW to the low side.AN10441 operating mechanism
Actionable 3.3 V-to-5 V starting point: use 4.7 kΩ from the low-side line to 3.3 V and 4.7 kΩ from the high-side line to 5 V, per SDA/SCL channel, then verify the measured rise time and LOW level at the intended bus speed and worst-case capacitance. This is a design starting example, not an onsemi datasheet requirement. When LOW, the ideal pull-up currents are approximately 3.3 V / 4.7 kΩ = 0.70 mA and 5 V / 4.7 kΩ = 1.06 mA; the active pull-down may need to sink contributions from both sides through the translator. Smaller resistors improve rise time but increase sink current and power; larger resistors reduce current but slow the RC edge. NXP states that low-to-high timing is dominated by the pull-up resistance and total node capacitance.AN10145 RC and pull-up tradeoff
Do not assume this circuit is suitable for push-pull buses, isolated grounds, long cables, heavy bus capacitance, difficult power sequencing, or guaranteed high-speed operation. Verify waveforms or use a purpose-built translator with specified timing and powered-off behavior.
Optional low-side load switch
For a small resistive load, connect source to ground, drain to the load, and the other load terminal to its positive supply. A practical design may add a gate pull-down—often tens to hundreds of kilohms—to hold the device off during reset, and a small series gate resistor where ringing or edge-rate control warrants it. For a relay, solenoid, or motor, add a correctly polarized flyback diode or other clamp at the inductive load. These are application design suggestions, not onsemi requirements specific to BSS138. Calculate conduction loss with guaranteed RDS(on) at the available gate voltage, not from VGS(th).
4. PCB Layout & Routing Guidelines
  • Minimize the switched-current loop: place the BSS138 close to the load or translated bus segment, and keep source return and drain paths short to reduce inductive overshoot and ground bounce.
  • Protect gate integrity: route the gate away from fast drain nodes; keep its return reference close, and place any gate resistor or pull-down next to the MOSFET.
  • Provide realistic thermal copper: the 0.36 W and 350 °C/W figures are tied to a minimum-pad test condition. Estimate junction rise from actual dissipation and do not treat 220 mA as automatically safe on every layout.
  • Use the correct SOT-23 land pattern and pin mapping: verify pin 1 Gate, pin 2 Source, pin 3 Drain before release. The onsemi datasheet includes a millimeter-controlled recommended mounting footprint.
  • Place pull-ups at their voltage domains: keep each pull-up referenced to the correct rail and route SDA/SCL compactly. Decoupling belongs at the devices or regulators generating VLOW and VHIGH; the passive MOSFET has no supply pin requiring a local bypass capacitor.
5. Common Pitfalls / Things to Watch Out For
  1. Using VGS(th) as the turn-on voltage. The 0.8–1.5 V threshold is measured at only 1 mA, while guaranteed RDS(on) is specified at 4.5 V and 10 V gate drive. A 3.3 V GPIO may work for light loads, but its resistance is not guaranteed by this datasheet.
  2. Using the I2C translator with push-pull drivers or poorly sized pull-ups. Bidirectional operation relies on open-drain behavior; push-pull contention can overstress drivers, while pull-ups that are too large produce slow RC edges and pull-ups that are too small exceed sink-current or VOL limits.AN10145 application constraints
An equivalent must be qualified by pinout, package/land pattern, electrical limits, gate-drive conditions, thermal behavior, and ordering status. A common family name or “SOT-23” description alone does not prove drop-in compatibility.

Table


PartVerified comparisonCompatibility assessment
Diodes Incorporated BSS138-7-FSOT-23; pin 1 G, pin 2 S, pin 3 D; 50 V; 200 mA at TA = 25 °C; RDS(on) 3.5 Ω max at VGS = 10 V and ID = 0.22 A.Pin-compatible and nominally footprint-compatible. Electrically close, but current, power, and thermal conditions differ; re-check worst-case dissipation and the exact land pattern.
Infineon 2N7002H6327XTSA2PG-SOT23, 60 V, 0.3 A; RDS(on) 4 Ω max at VGS = 4.5 V/ID = 0.25 A and 3 Ω max at VGS = 10 V/ID = 0.5 A; H6327 is 3000 pieces/reel.Verified functional electrical alternative, not a verified PCB drop-in. The pinout drawing was not machine-verified in this review; compare the primary Infineon drawing before reusing the same footprint.
7. Sourcing & Purchasing Guide

Table


AttributeDetails
Primary DistributorsUse authorized channels such as Digi-Key, Mouser, Arrow, Newark/Farnell, or onsemi-authorized regional distributors. Verify manufacturer, exact MPN, lifecycle, and traceability at purchase time rather than relying on static stock claims.
Packaging OptionsThe onsemi Rev. 7 datasheet lists BSS138 and BSS138-G in SOT-23-3 (Pb-Free), shipped 3000 pieces per tape-and-reel; it does not publish a separate packaging-suffix mapping beyond those device labels.
Standard MOQFactory pack: 3000/reel for the listed onsemi ordering row. Distributor cut tape: often available from one piece, but that is a distributor service/MOQ, not the manufacturer’s factory MOQ; verify the live listing.
Sourcing AdviceMatch the complete orderable code and manufacturer, confirm SOT-23 pinout and top marking, prefer authorized supply for production, and retain lot/date-code traceability. Do not substitute another vendor’s BSS138 or a 2N7002 without rechecking guaranteed RDS(on), current and thermal test conditions, footprint geometry, and pin numbering.
Sources
Verification limitations
  • The NXP application notes were read from primary PDFs and linked inline; Flux citation indexing for those notes remained pending, so those application-note claims use direct primary-source links rather than flux:cite markers.
  • The onsemi recommended footprint drawing is present, but numeric pad dimensions were not reliably extracted; use the primary drawing or a validated JLCPCB-compatible SOT-23 footprint rather than estimated land dimensions.
  • The Infineon alternative’s electrical ratings and packaging were verified, but its graphical pinout was not machine-verified; no pin-compatible drop-in claim is made.
  • Distributor cut-tape MOQ, stock, price, and lead time are live commercial data and were intentionally not frozen into this guide.
  • 1. Quick Specifications

  • 2. Pinout & Connections

  • 3. Standard Application Circuit

  • Bidirectional open-drain I2C level translation

  • Optional low-side load switch

  • 4. PCB Layout & Routing Guidelines

  • 5. Common Pitfalls / Things to Watch Out For

  • 6. Popular Alternatives & Equivalents

  • 7. Sourcing & Purchasing Guide

  • Sources

  • Verification limitations