Sensors

High-Voltage SPI Digital Potentiometer – Single-channel 8-bit digital potentiometer for programmable gain control, industrial automation, instrumentation, audio equipment, sensor calibration, power supplies, and embedded analog signal conditioning. Features 50 kΩ nominal resistance with 256 wiper positions (8-bit resolution), a linear taper, and an SPI serial interface for precise digital control. Supports separate digital and analog supply rails, with a digital supply of 1.8 V to 5.5 V and an analog supply up to 36 V (10 V to 36 V single supply or ±5 V to ±18 V dual supply), making it suitable for high-voltage analog applications. Includes 145 Ω typical wiper resistance, 100 ppm/°C temperature coefficient, volatile memory, shutdown capability, and AEC-Q100 qualification for high-reliability environments. Operates over a −40°C to +125°C temperature range and is housed in a 14-pin TSSOP package. #Microchip #MCP41HV51503EST #MCP41HV51 #DigitalPotentiometer #SPIPotentiometer #ProgrammableResistor #HighVoltage #AnalogControl #SignalConditioning #IndustrialElectronics #AECQ100 #EmbeddedSystems

Temperature Sensor Digital, Local -40°C ~ 125°C 16 b 4-PICOSTAR (0.76x0.76) Digital Temperature Sensor — measures temperature using a high-accuracy digital sensing element with an I²C-compatible interface. The TMP114AIYMTR operates from a 1.7 V to 5.5 V supply, provides 16-bit temperature resolution, and supports a temperature range of −40°C to +125°C in a small 6-pin SOT-23 package. #TemperatureSensor #DigitalSensor #I2C #PCBComponent #TexasInstruments #TMP114AIYMTR

Battery Power Management IC Multi-Chemistry 14-TSSOP The bq34210-Q1 1-Series Cell System-Side CEDV Fuel Gauge provides fuel gauging and End-of-Service (EOS) Determination for 1-series cell batteries in applications that encounter infrequent discharge, such as eCall systems and uninterruptible power supplies (UPS) for backup during power failures, where batteries may stay connected to a charging power source most of their lifetime until needed. The bq34210-Q1 fuel gauge supports multiple battery chemistries, including Li-Ion, LiFePO4, and NiMH. The gas gauging function uses voltage, current, and temperature data along with Compensated End-ofDischarge (CEDV) technology to provide State-ofCharge (SOC) and State-of-Health (SOH) data. The device's EOS Determination function alerts when battery capability has degraded and is approaching the end of its usable service. Battery fuel gauging with the bq34210-Q1 fuel gauge requires connections only to PACK+ (P+) and PACK– (P–) for a removable battery pack or embedded battery management system. Features 1• Automotive-Qualified AEC-Q100, Grade 3 • 1-Series Cell Battery Fuel Gauge Supports Li-Ion, LiFePO4, and NiMH (3-Cell) Chemistries – Resides on System Board – Powers Directly from the Battery with Integrated LDO – Supports a Low-Value External Sense Resistor (10 mΩ) • Learning Load Enable (LEN) from Host • Ultra-Low Power Consumption in NORMAL (50 µA) and SLEEP (9 µA) Modes • Supports Replacement Batteries • Accurate End-of-Service (EOS) Determination for Batteries in Rarely Discharged Applications • CEDV Gas Gauge for 1-Series Cell Batteries, Providing: – State-of-Charge (SOC) – Time-to-Empty (TTE) – State-of-Health (SOH) • High-Side and Low-Side Current Sensing Options • Internal Temperature Sensor OR External Thermistor • Microcontroller Peripheral Interface Supports: – 400-kHz I 2C™ Serial Interface – Configurable Interrupt (ALERT) for SOC, Battery Levels, Temperature Faults, and Charge/Discharge Status 2 Applications • eCall Systems • Telematics Backup Systems • Uninterruptible Power Supply (UPS) Backup Systems • Emergency Battery Power Modules #BatteryFuelGauge #BatteryManagement #FuelGaugeIC #AutomotiveElectronics #TexasInstruments #LiIonBattery #LiFePO4 #I2C #PowerManagement #AECQ100 #BackupBattery #UPS #EmbeddedSystems