Inverter IC 6 Channel Schmitt Trigger 14-TSSOP #CommonPartsLibrary #IntegratedCircuit #Logic #Trigger #Inverter

5V Trigger Relay Module For Arduino And Raspberry Pi 5V Trigger Relay Module For Arduino And Raspberry Pi

Inverter IC 6 Channel Schmitt Trigger 14-SO

NAND Gate IC 4 Channel Schmitt Trigger 14-SOIC #CommonPartsLibrary #IntegratedCircuit #Logic #Gate #Inverter

The NE555 devices are precision timing circuits capable of producing accurate time delays or oscillation. In time-delay or monostable operating modes, the timed interval is controlled by a single external resistor and capacitor network. In the astable mode of operation, the frequency and duty cycle are controlled independently with two external resistors and a single external capacitor. Each timer has a trigger level equal to approximately one-third of the supply voltage and a threshold level equal to approximately two-thirds of the supply voltage. These levels can be altered by use of the control voltage pin (CONT). When the trigger input (TRIG) is less than the trigger level, the flip-flop is set and the output goes high. If TRIG is greater than the trigger level and the threshold input (THRES) is greater than the threshold level, the flip-flop is reset and the output is low. The reset input (RESET) overrides all other inputs and is used to initiate a new timing cycle. If RESET is low, the flip-flop is reset and the output is low. Whenever the output is low, a lowimpedance path is provided between the discharge pin (DISCH) and the ground pin (GND). Tie all unused inputs to an appropriate logic level to prevent false triggering. The output circuit is capable of sinking or sourcing current up to 200mA. Operation is specified for supplies of 5V to 15V. With a 5V supply, output levels are compatible with TTL inputs. Features - Timing from microseconds to hours - Astable or monostable operation - Adjustable duty cycle - TTL-compatible output can sink or source up to 200mA - On products compliant to MIL-PRF-38535, all parameters are tested unless otherwise noted. Applications - Pulse-shaping circuits - Missing-pulse detectors - Pulse-width modulators - Pulse-position modulators - Sequential timers - Pulse generators -F requency dividers - Industrial controls

USB-C (USB TYPE-C) USB 2.0 Receptacle Connector 24 (16+8 Dummy) Position Surface Mount, Right Angle; Through Hole USB Type-C receptacle 16 pin USB2.0 The USB4215-03-A is a USB Type-C receptacle connector designed for USB 2.0 applications. It features a 16-pin configuration supporting reversible plug orientation with standard USB 2.0 differential data lines and configuration channel (CC) pins. The connector is intended for surface-mount PCB assembly with through-hole shell stakes for enhanced mechanical strength. It is widely used in compact embedded systems for power delivery, charging interfaces, and basic data communication. Key Features USB Type-C receptacle (USB 2.0 compliant) 16 functional pins (no SuperSpeed support) Reversible plug orientation Surface-mount contacts with through-hole shell tabs Compact, low-profile design High insertion cycle durability Suitable for automated assembly Electrical Characteristics Rated Current: VBUS: up to 5.0 A (depending on PCB design and cable) Signal pins: 0.25 A max Rated Voltage: 20 V DC max Contact Resistance: ≤ 40 mΩ Insulation Resistance: ≥ 100 MΩ Dielectric Withstanding Voltage: 100 V AC Mechanical Characteristics Mounting Type: Surface Mount (SMT) with Through-Hole Shield Tabs Number of Positions: 16 Mating Cycles: 10,000 cycles (typical) Insertion Force: 5–20 N Extraction Force: 8–20 N Material Specifications Contacts: Copper Alloy Contact Plating: Gold over Nickel Housing: High-temperature thermoplastic (UL94V-0) Shell: Stainless Steel Environmental Characteristics Operating Temperature Range: -25°C to +85°C Storage Temperature Range: -40°C to +85°C RoHS Compliant: Yes Halogen Free: Yes Pin Configuration (USB 2.0 Type-C) VBUS (Power) GND (Ground) D+ / D− (USB 2.0 differential pair) CC1 / CC2 (Configuration channel) SBU pins (optional/unused in USB 2.0 designs) Applications USB power input (5 V / USB-C PD trigger designs) Embedded systems and development boards Consumer electronics Charging interfaces Low-speed USB communication devices Packaging Tape & Reel for automated pick-and-place assembly Compliance & Standards USB Type-C Specification (USB 2.0 interface) RoHS / REACH compliant UL recognized materials #CommonPartsLibrary #Connector #USB-C

20 Position Receptacle Connector 0.100" (2.54mm) Through Hole Tin The SSW-120-01-T-S is a single-row, 20-position female (receptacle) socket strip with a 2.54 mm (0.1") pitch, intended for through-hole PCB mounting. It uses Samtec’s Tiger Buy™ contact system, providing reliable electrical performance and durability for repeated mating cycles. It is commonly used in embedded systems, development boards, and general PCB interconnections, especially where standard 0.1" headers are required. Female header 1x20 2.54mm Key Features Standard 2.54 mm Pitch Industry-standard spacing compatible with most pin headers and prototyping systems 20 Positions, Single Row Ideal for compact signal connections and header interfaces Tiger Buy™ Contact System Provides low insertion force and reliable electrical contact Available in standard or low insertion force variants Through-Hole Mounting Ensures strong mechanical retention and durability on PCBs Tin-Plated Contacts (T option) Cost-effective plating suitable for general-purpose applications High-Speed Capability Supports signals up to ~8 Gbps, depending on application and layout Wide Operating Temperature Range Typically −55 °C to +105 °C, suitable for industrial environments Material Construction Contacts: Phosphor bronze Insulator: High-temperature plastic (e.g., LCP) Versatile Mating Compatibility Mates with common Samtec header series (TSW, MTSW, etc.) and standard 0.025" square posts #CommonPartsLibrary #Connector #SSW-120

555 Type, Timer/Oscillator (Single) IC 2.1MHz 8-SOIC The TLC555IDR is a low-power CMOS timer device designed as a functional replacement for the standard bipolar 555 timer while providing significantly reduced supply current and improved operating efficiency. The device supports both astable and monostable operating modes and is commonly used for timing generation, pulse shaping, oscillation, PWM generation, delay circuits, and frequency generation applications. The CMOS architecture enables low power consumption, rail-to-rail output capability, and stable timing performance over a wide operating voltage range. The device is suitable for battery-powered systems, portable electronics, industrial controls, instrumentation, consumer products, and embedded electronic designs. The TLC555IDR is supplied in a compact SOIC surface-mount package intended for automated PCB assembly and space-constrained applications. Electrical Characteristics CMOS low-power timer architecture Functional equivalent to standard 555 timer devices Wide operating supply voltage range Low quiescent supply current High input impedance Rail-to-rail output swing capability Stable threshold and trigger levels Compatible with TTL and CMOS logic levels Capable of astable and monostable operation Adjustable duty cycle and frequency operation High output drive capability for direct interfacing Low noise and improved switching performance compared to bipolar 555 timers Functional Features Precision timing generation Oscillator and clock generation Pulse-width modulation support One-shot pulse generation Delay timer implementation Missing pulse detection Frequency divider implementation Sequential timing control LED flashing and tone generation PWM motor and power control applications Package Information Surface-mount SOIC package Standard tape-and-reel packaging format Compact footprint for automated assembly RoHS compliant device construction Environmental and Operating Conditions Industrial operating temperature range ESD protection handling required Suitable for commercial and industrial embedded systems Designed for low-power electronic applications Typical Applications Timer circuits Pulse generators Oscillators PWM controllers LED flashers Alarm and tone generators Frequency generators Power management timing Embedded control systems Portable battery-powered electronics #commonpartslibrary #integratedcircuit #timer #oscillator

Inverter IC 6 Channel Schmitt Trigger 14-PDIP #commonpartslibrary #integratedcircuit #inverter

Inverter IC 1 Channel Schmitt Trigger SOT-353 #commonpartslibrary #integratedcircuit #inverter

EEPROM Memory IC 256Kbit I2C 1 MHz 450 ns 8-SO The M24256E-FMN6TP is a 256-Kbit (32 Kbyte) I²C-compatible serial EEPROM from STMicroelectronics. It is designed for reliable, non-volatile data storage in a wide range of electronic applications including consumer, industrial, and automotive systems. The device supports standard (100 kHz), fast (400 kHz), and fast-mode plus (1 MHz) I²C communication, enabling efficient data transfer. It features byte and page write operations, low power consumption, and a high endurance of write cycles, making it suitable for frequent data logging and configuration storage. Housed in a compact SO8 package, the device is optimized for space-constrained PCB designs while maintaining robust performance and data retention capabilities. Key Features Memory size: 256 Kbit (32 Kbyte) Interface: I²C (2-wire serial interface) Clock frequency: Standard mode: 100 kHz Fast mode: 400 kHz Fast-mode Plus: 1 MHz Supply voltage range: 1.7 V to 5.5 V Page write capability: up to 64 bytes Write cycle time: ~5 ms (typical) Data retention: > 200 years Endurance: > 4 million write cycles Hardware write protection available ESD protection and latch-up immunity Functional Description The device operates as a slave on the I²C bus and supports: Byte write and read Page write (up to 64 bytes) Random and sequential read operations Memory addressing is internally managed using a 16-bit address pointer, allowing access to the full 32 KB memory array. The device includes an internal write cycle controller, eliminating the need for external timing management. Pin Configuration (SO8 Package) A0, A1, A2: Device address inputs VSS: Ground SDA: Serial data line SCL: Serial clock line WC: Write control (hardware write protection) VCC: Supply voltage Absolute Maximum Ratings Supply voltage (VCC): -0.3 V to 6.5 V Input voltage: -0.3 V to VCC + 0.6 V Storage temperature: -65°C to +150°C Operating temperature (industrial grade): -40°C to +85°C Electrical Characteristics Low standby current: < 1 µA (typical) Operating current: < 1 mA Input/output compatible with CMOS logic levels Schmitt trigger inputs for noise immunity Timing Characteristics Write cycle time: 5 ms (typical) Fast-mode Plus support up to 1 MHz Sequential read supports continuous data streaming Package Information Package type: SO8 (8-lead Small Outline) Mounting: Surface-mount (SMD) Tape & reel packaging (TP suffix) Applications Configuration storage Calibration data storage Data logging systems Industrial control systems Consumer electronics Embedded systems requiring non-volatile memory Advantages High endurance and long data retention Wide voltage range (ideal for mixed-voltage systems) Compact footprint High-speed I²C compatibility (up to 1 MHz) #commonpartslibrary #integratedcircuit #memory

Inverter IC 6 Channel Schmitt Trigger 14-SOIC #CommonPartsLibrary #IntegratedCircuit #Logic #Gates #Inverters #CD40106

NAND Gate IC 4 Channel Schmitt Trigger 14-TSSOP #CommonPartsLibrary #IntegratedCircuit #Logic #Gate #Inverter #CD4093

Inverter IC 1 Channel Schmitt Trigger SC-88A (SC-70-5/SOT-353) #CommonPartsLibrary #IntegratedCircuit #Logic #Gate #Inverter #74HC1G14

Inverter IC 6 Channel Schmitt Trigger 14-SO #CommonPartsLibrary #IntegratedCircuit #Logic #Gate #Inverter #74LVC

Schmitt Trigger 2 4.9ns@5V,50pF 1uA 1.65V~5.5V UFDFN-6 Inverters ROHS #CommonPartsLibrary #IntegratedCircuit #Logic #Gate #Inverter