ARM® Cortex®-M4 series Microcontroller IC 32-Bit Single-Core 168MHz 1MB (1M x 8) FLASH 64-LQFP (10x10) Arm® Cortex®-M4 32b MCU+FPU, 210DMIPS, up to 1MB flash/192+4KB RAM, USB OTG HS/FS, Ethernet, 17 TIMs, 3 ADCs, 15 comm. interfaces, and camera Includes ST state-of-the-art patented technology • Core: Arm® 32-bit Cortex®-M4 CPU with FPU, Adaptive real-time accelerator (ART Accelerator) allowing 0-wait state execution from flash memory, frequency up to 168 MHz, memory protection unit, 210 DMIPS/ 1.25 DMIPS/MHz (Dhrystone 2.1), and DSP instructions • Memories – Up to 1 Mbyte of flash memory – Up to 192+4 Kbytes of SRAM including 64- Kbyte of CCM (core coupled memory) data RAM – 512 bytes of OTP memory – Flexible static memory controller supporting CompactFlash™, SRAM, PSRAM, NOR and NAND memories • LCD parallel interface, 8080/6800 modes • Clock, reset, and supply management – 1.8 V to 3.6 V application supply and I/Os – POR, PDR, PVD and BOR – 4-to-26 MHz crystal oscillator – Internal 16 MHz factory-trimmed RC (1% accuracy) – 32 kHz oscillator for RTC with calibration – Internal 32 kHz RC with calibration • Low-power operation – Sleep, Stop, and Standby modes –VBAT supply for RTC, 20×32-bit backup registers + optional 4 KB backup SRAM • 3×12-bit, 2.4 MSPS A/D converters: up to 24 channels and 7.2 MSPS in triple interleaved mode • 2×12-bit D/A converters • General-purpose DMA: 16-stream DMA controller with FIFOs and burst support • Up to 17 timers: up to twelve 16-bit and two 32- bit timers up to 168 MHz, each with up to 4 IC/OC/PWM or pulse counter and quadrature (incremental) encoder input • Debug mode – Serial wire debug (SWD) & JTAG interfaces – Cortex-M4 Embedded Trace Macrocell™ • Up to 140 I/O ports with interrupt capability – Up to 136 fast I/Os up to 84 MHz – Up to 138 5 V-tolerant I/Os • Up to 15 communication interfaces – Up to 3 × I2C interfaces (SMBus/PMBus) – Up to 4 USARTs/2 UARTs (10.5 Mbit/s, ISO 7816 interface, LIN, IrDA, modem control) – Up to 3 SPIs (42 Mbits/s), 2 with muxed full-duplex I2S to achieve audio class accuracy via internal audio PLL or external clock – 2 × CAN interfaces (2.0B Active) – SDIO interface • Advanced connectivity – USB 2.0 full-speed device/host/OTG controller with on-chip PHY – USB 2.0 high-speed/full-speed device/host/OTG controller with dedicated DMA, on-chip full-speed PHY and ULPI – 10/100 Ethernet MAC with dedicated DMA: supports IEEE 1588v2 hardware, MII/RMII #commonpartslibrary #integratedcircuit #microcontroller

Phase Lock Loop (PLL) IC 21MHz 1 16-SOIC (0.154", 3.90mm Width) #CommonPartsLibrary #IntegratedCircuit #Clock/Timing #PLLs #Frequency-Synthesizer #74HC4046

ARM Microcontrollers - MCU ARM M4 1024 FLASH 168 Mhz 192kB SRAM 100-LQFP (14x14) Arm® Cortex®-M4 32b MCU+FPU, 210DMIPS, up to 1MB Flash/192+4KB RAM, USB OTG HS/FS, Ethernet, 17 TIMs, 3 ADCs, 15 comm. interfaces & camera • Core: Arm® 32-bit Cortex®-M4 CPU with FPU, Adaptive real-time accelerator (ART Accelerator) allowing 0-wait state execution from Flash memory, frequency up to 168 MHz, memory protection unit, 210 DMIPS/ 1.25 DMIPS/MHz (Dhrystone 2.1), and DSP instructions • Memories – Up to 1 Mbyte of Flash memory – Up to 192+4 Kbytes of SRAM including 64- Kbyte of CCM (core coupled memory) data RAM – 512 bytes of OTP memory – Flexible static memory controller supporting Compact Flash, SRAM, PSRAM, NOR and NAND memories • LCD parallel interface, 8080/6800 modes • Clock, reset and supply management – 1.8 V to 3.6 V application supply and I/Os – POR, PDR, PVD and BOR – 4-to-26 MHz crystal oscillator – Internal 16 MHz factory-trimmed RC (1% accuracy) – 32 kHz oscillator for RTC with calibration – Internal 32 kHz RC with calibration • Low-power operation – Sleep, Stop and Standby modes –VBAT supply for RTC, 20×32 bit backup registers + optional 4 KB backup SRAM • 3×12-bit, 2.4 MSPS A/D converters: up to 24 channels and 7.2 MSPS in triple interleaved mode • 2×12-bit D/A converters • General-purpose DMA: 16-stream DMA controller with FIFOs and burst support • Up to 17 timers: up to twelve 16-bit and two 32- bit timers up to 168 MHz, each with up to 4 IC/OC/PWM or pulse counter and quadrature (incremental) encoder input • Debug mode – Serial wire debug (SWD) & JTAG interfaces – Cortex-M4 Embedded Trace Macrocell™ • Up to 140 I/O ports with interrupt capability – Up to 136 fast I/Os up to 84 MHz – Up to 138 5 V-tolerant I/Os • Up to 15 communication interfaces – Up to 3 × I2C interfaces (SMBus/PMBus) – Up to 4 USARTs/2 UARTs (10.5 Mbit/s, ISO 7816 interface, LIN, IrDA, modem control) – Up to 3 SPIs (42 Mbits/s), 2 with muxed full-duplex I2S to achieve audio class accuracy via internal audio PLL or external clock – 2 × CAN interfaces (2.0B Active) – SDIO interface • Advanced connectivity – USB 2.0 full-speed device/host/OTG controller with on-chip PHY – USB 2.0 high-speed/full-speed device/host/OTG controller with dedicated DMA, on-chip full-speed PHY and ULPI – 10/100 Ethernet MAC with dedicated DMA: supports IEEE 1588v2 hardware, MII/RMII #CommonPartsLibrary #IntegratedCircuit #Microcontroller #STM32F407

Fanout Distribution, Fractional N, Integer N, Clock/Frequency Synthesizer (RF) IC 4.4GHz 1 32-VFQFN Exposed Pad, CSP Timer #PLL #commonpartslibrary

ARM® Cortex® M3 STM32F1 Microcontroller IC 32-Bit Single-Core 72MHz 64KB (64K x 8) FLASH Medium-density performance line Arm®-based 32-bit MCU with 64 or 128 KB Flash, USB, CAN, 7 timers, 2 ADCs, 9 com. interfaces Arm® 32-bit Cortex®-M3 CPU core – 72 MHz maximum frequency, 1.25 DMIPS/MHz (Dhrystone 2.1) performance at 0 wait state memory access – Single-cycle multiplication and hardware division • Memories – 64 or 128 Kbytes of Flash memory – 20 Kbytes of SRAM • Clock, reset and supply management – 2.0 to 3.6 V application supply and I/Os – POR, PDR, and programmable voltage detector (PVD) – 4 to 16 MHz crystal oscillator – Internal 8 MHz factory-trimmed RC – Internal 40 kHz RC – PLL for CPU clock – 32 kHz oscillator for RTC with calibration • Low-power – Sleep, Stop and Standby modes – VBAT supply for RTC and backup registers • 2x 12-bit, 1 µs A/D converters (up to 16 channels) – Conversion range: 0 to 3.6 V – Dual-sample and hold capability – Temperature sensor • DMA – 7-channel DMA controller – Peripherals supported: timers, ADC, SPIs, I 2Cs and USARTs • Up to 80 fast I/O ports – 26/37/51/80 I/Os, all mappable on 16 external interrupt vectors and almost all 5 V-tolerant Debug mode: – Serial wire debug (SWD) and JTAG interfaces • Seven timers – Three 16-bit timers, each with up to 4 IC/OC/PWM or pulse counter and quadrature (incremental) encoder input – 16-bit, motor control PWM timer with dead-time generation and emergency stop – Two watchdog timers (independent and window) – SysTick timer 24-bit downcounter • Up to nine communication interfaces – Up to two I2C interfaces (SMBus/PMBus®) – Up to three USARTs (ISO 7816 interface, LIN, IrDA capability, modem control) – Up to two SPIs (18 Mbit/s) – CAN interface (2.0B Active) – USB 2.0 full-speed interface • CRC calculation unit, 96-bit unique ID • Packages are ECOPACK #commonpartslibrary #integratedcircuit #microcontroller #stm32f1

Audio D/A Converter ICs SABRE 8 Channel Smart DAC with Line Drivers, ASP2, 7mmx7mm, 48-QFN The ES9082Q is a high-performance stereo digital-to-analog converter (DAC) developed by ESS Technology for premium audio applications requiring exceptional sound quality, low power consumption, and compact integration. It utilizes the patented HyperStream® architecture and Time Domain Jitter Eliminator technology to deliver highly accurate audio reproduction with ultra-low distortion and noise characteristics. The device supports high-resolution PCM and DSD audio formats, making it suitable for portable audio devices, USB DACs, digital media players, automotive infotainment systems, wireless audio products, and professional audio equipment. The ES9082Q integrates advanced digital filtering, low-jitter clock management, and flexible audio interface support while maintaining efficient power operation for battery-powered applications. Designed for compact embedded audio systems, the ES9082Q provides excellent dynamic range and signal fidelity while minimizing external component requirements. Its architecture enables high-quality playback performance across a wide range of consumer and industrial audio applications. Electrical Characteristics Supply voltage supports low-voltage digital and analog power domains optimized for portable and embedded applications. The device operates with low power consumption while maintaining high audio performance. Integrated power management supports efficient system-level implementation. Audio Performance The converter supports high-resolution stereo audio output with advanced oversampling and noise shaping technology. It delivers ultra-low total harmonic distortion plus noise performance and high dynamic range suitable for high-fidelity audio playback systems. PCM audio data rates support standard and high-resolution formats up to 32-bit depth with sampling frequencies extending to high-definition audio ranges. Native DSD playback capability is also supported for audiophile-grade applications. Digital Audio Interface The ES9082Q supports industry-standard serial audio interfaces including I²S, left-justified, and related digital audio communication protocols. Flexible master and slave clocking configurations enable compatibility with a wide variety of host processors and audio controllers. Integrated jitter suppression circuitry improves clock stability and minimizes timing-induced audio artifacts. Integrated Features The device incorporates digital interpolation filters, volume control functions, soft mute capability, and programmable audio processing features. Internal PLL and clock management circuitry reduce external timing component requirements. Built-in low-noise analog output stages simplify audio signal chain design and reduce overall PCB footprint. Package Information The ES9082Q is provided in a compact surface-mount package optimized for space-constrained audio products. The package supports automated assembly and high-density PCB layouts commonly used in portable and embedded systems. Typical Applications Applications include portable audio players, USB DAC modules, wireless speakers, automotive audio systems, headphones, digital amplifiers, embedded multimedia devices, smart home audio equipment, and professional audio playback systems. #commonpartslibrary #integratedcircuit #audioic #dac #stereodac #esstechnology #es9082q #highresolutionaudio #audiophile #digitalaudio #analogaudio #i2s #dsd #pcm #embeddedaudio #consumerelectronics #portableaudio #usbdac #hifi #signalprocessing #lownoise #lowdistortion #electronicsdesign #pcbdesign #hardwareengineering #electroniccomponents #semiconductor #mixedsignal #audioelectronics #soundquality

Phase Lock Loop (PLL) IC 2.4MHz 1 16-DIP (0.300", 7.62mm) CD4046BE is a CMOS Micropower Phase-Locked Loop (PLL) integrated circuit that combines a linear Voltage-Controlled Oscillator (VCO), two phase comparators, a source follower, and a Zener diode in a single package. It is designed for frequency synthesis, frequency detection, FM demodulation, clock recovery, motor speed control, and other synchronization applications. The device operates over a wide supply voltage range and offers low power consumption, high noise immunity, and excellent VCO linearity. Key Features Wide operating supply voltage range: 3 V to 18 V Integrated Voltage-Controlled Oscillator (VCO) Two selectable phase comparators for flexible PLL design Operating frequency range up to approximately 1.4 MHz Very low power consumption High VCO linearity (typically <1%) Low frequency drift with temperature VCO inhibit control for ON/OFF keying applications Built-in source follower output for demodulation applications High noise immunity characteristic of CMOS technology Available in 16-pin PDIP (CD4046BE) package Typical Applications Frequency synthesis and multiplication FM modulation and demodulation Frequency discrimination Clock recovery and data synchronization Tone decoding Voltage-to-frequency conversion FSK modulation/demodulation Motor speed control systems Signal tracking and phase synchronization circuits Hashtags #CD4046BE #PLL #PhaseLockedLoop #VCO #ClockRecovery #FrequencySynthesizer #FMDemodulator #FSKModulation #CMOS #TexasInstruments #AnalogIC #TimingIC #SignalProcessing #EmbeddedSystems #ElectronicsDesign

ADC, Audio 32 b 8k ~ 192k I2S 20-WQFN (3x3) The PCM1822 is a high-performance, Burr-Brown™ audio analog-to-digital converter (ADC) that supports simultaneous sampling of up to two analog channels. The device supports single-ended and differential line and microphone inputs with a 1-VRMS full-scale signal. The device integrates a phase-locked loop (PLL), a DC removal high-pass filter (HPF), and supports sample rates up to 192 kHz. The device supports time-division multiplexing (TDM) or I2S audio formats, selectable with the hardware pin level. Additionally, the PCM1822 supports master and slave mode selection for the audio bus interface operation. These integrated high-performance features, along with the ability to be powered from a single supply of 3.3 V, make the device an excellent choice for costsensitive, space-constrained audio systems in far-field microphone recording applications. The PCM1822 is specified from –40°C to +125°C, and is offered in a 20-pin WQFN package. Features • Stereo high-performance ADC: – 2-channel analog microphones or line-in • ADC line and microphone differential and singleended input performance: – PCM1822 dynamic range: • 117-dB, dynamic range enhancer enabled • 111-dB, dynamic range enhancer disabled – THD+N: –95 dB • 1-VRMS full-scale input • ADC sample rate (fS) = 8 kHz to 192 kHz • Hardware pin control configurations • Linear-phase or low-latency filter selection • Flexible audio serial data interface: – Master or slave interface selection – 32-bits, 2-channel TDM – 32-bits, 2-channel I2S • Automatic power-down upon loss of audio clocks • Integrated high-performance audio PLL • Single-supply operation: 3.3 V • I/O-supply operation: 3.3 V or 1.8 V • Power consumption for 3.3-V AVDD supply: – 19.6 mW/channel at 16-kHz sample rate – 21.3 mW/channel at 48-kHz sample rate #CommonPartsLibrary #IntegratedCircuit #PCM1822IRTER #TexasInstruments #AudioADC #StereoADC #BurrBrown #I2S #TDM #AudioElectronics #EmbeddedAudio #SmartSpeaker #AVReceiver #HighResolutionAudio #PCBDesign #ElectronicsDesign #SignalProcessing

PLL Frequency Synthesizer IC 3.6GHz, 1.7GHz 1 20-UFLGA #commonpartslibrary #integratedcircuit #frequency #synthesizer

Fanout Distribution, Fractional N, Integer N, Clock/Frequency Synthesizer (RF) IC 4.4GHz 1 32-WFQFN Exposed Pad, CSP #Timer #PLL #commonpartslibrary

6.4-GHz low noise fractional-N PLL with ramp/chirp generation #CommonPartsLibrary #IntegratedCircuit #Clock/Timing #PLLs #Clock-Generator #LMX2491

Fractional N Synthesizer (RF) IC 6.1GHz 1 24-WFQFN Exposed Pad, CSP #Timer #PLL #commonpartslibrary

IC 1.028GHz 1 44-VFQFN Exposed Pad #Timer #PLL #commonpartslibrary

Clock/Frequency Synthesizer (RF), Phase Detector IC 400MHz 1 20-WFQFN Exposed Pad, CSP #Timer #PLL #commonpartslibrary

Clock/Frequency Synthesizer (RF), Phase Detector IC 400MHz 1 16-TSSOP (0.173", 4.40mm Width) #Timer #PLL #commonpartslibrary

IC 350MHz 1 64-VFQFN Exposed Pad #Timer #PLL #commonpartslibrary

IC 1.028GHz 1 44-VFQFN Exposed Pad #Timer #PLL #commonpartslibrary

IC 350MHz 1 44-VFQFN Exposed Pad #Timer #PLL #commonpartslibrary

IC 350MHz 1 44-VFQFN Exposed Pad #Timer #PLL #commonpartslibrary

IC 350MHz 1 44-VFQFN Exposed Pad Timer #PLL #commonpartslibrary

ADC, Audio 768k I²C, SPI 24-WQFN (4x4) The TLV320ADC3140 is a Burr-Brown™ highperformance, audio analog-to-digital converter (ADC) that supports simultaneous sampling of up to four analog channels or eight digital channels for the pulse density modulation (PDM) microphone input. The device supports line and microphone inputs, and allows for both single-ended and differential input configurations. The device integrates programable channel gain, digital volume control, a programmable microphone bias voltage, a phase-locked loop (PLL), a programmable high-pass filter (HPF), biquad filters, low-latency filter modes, and allows for sample rates up to 768 kHz. The device supports time-division multiplexing (TDM), I2S, or left-justified (LJ) audio formats, and can be controlled with either the I2C or SPI interface. These integrated high-performance features, along with the ability to be powered from a single-supply of 3.3 V or 1.8 V, make the device an excellent choice for space-constrained audio systems in far-field microphone recording applications. #commonpartslibrary #integratedcircuit #adc #audio

DIP-14 Clock Generators / Frequency Synthesizers / PLL ROHS #CommonPartsLibrary #IntegratedCircuit #Clock #PLL

Analog to Digital Converters - ADC Single-channel, 9-bit, 1.3-GSPS analog-to-digital converter (ADC) with JESD204C interface 144-FCBGA -40 to 85 ADC09xJ1300 is a family of quad, dual and single channel, 9-bit, 1.3GSPS analog-to-digital converters (ADC). Low power consumption, high sampling rate and 9-bit resolution makes the ADC09xJ1300 ideally suited for suited for a variety of multi-channel communications and test systems. Full-power input bandwidth (-3dB) of 6GHz enables direct RF sampling of L-band and S-band. A number of clocking features are included to relax system hardware requirements, such as an internal phase-locked loop (PLL) with integrated voltagecontrolled oscillator (VCO) to generate the sampling clock. Four clock outputs are provided to clock the logic and SerDes of the FPGA or ASIC. A timestamp input and output is provided for pulsed systems. JESD204C serialized interface decreases system size by reducing the amount of printed circuit board (PCB) routing. Interface modes support from 2 to 8 lanes (dual and quad channel devices) or 1 to 4 lanes (for the single channel device), with SerDes baud-rates up to 17.16Gbps, to allow the optimal configuration for each application. Features • ADC Core: – Resolution: 9 Bit – Maximum sampling rate: 1.3GSPS – Non-interleaved architecture – Internal dither reduces high-order harmonics • Performance specifications (–1dBFS): – SNR (100 MHz): 53.5dBFS – ENOB (100 MHz): 8.5 Bits – SFDR (100 MHz): 64dBc – Noise floor (–20dBFS): –143dBFS • Full-scale input voltage: 80 mVPP-DIFF • Full-power input bandwidth: 6GHz • JESD204C Serial data interface: – Support for 2 to 8 (Quad/Dual channel) or 1 to 4 (Single channel) total SerDes lanes – Maximum baud-rate: 17.16Gbps – 64B/66B and 8B/10B encoding modes – Subclass-1 support for deterministic latency – Compatible with JESD204B receivers • Optional internal sampling clock generation – Internal PLL and VCO (7.2–8.2GHz) • SYSREF Windowing eases synchronization • Four clock outputs simplify system clocking – Reference clocks for FPGA or adjacent ADC – Reference clock for SerDes transceivers • Timestamp input and output for pulsed systems • Power consumption (1GSPS): – Quad Channel: 450mW / channel – Dual channel: 625mW / channel – Single channel: 940mW • Power supplies: 1.1V, 1.9V #CommonPartsLibrary #IntegratedCircuit #ADC #HighSpeedADC #RFADC #JESD204C #13GSPS #9bitADC #DirectRFSampling #TexasInstruments #MixedSignal #DataAcquisition #JESD204

Audio 16 b, 20 b, 24 b, 32 b 768k I2C, I2S, TDM 20-WQFN (3x3) The TAA3020IRTER is a high-performance 2-channel audio analog-to-digital converter (ADC) from Texas Instruments, designed for professional and embedded audio applications. It supports up to two analog microphone/line inputs or four digital PDM microphone channels with simultaneous sampling. The device delivers excellent audio quality with a 104 dB dynamic range, supports sample rates up to 768 kHz, and integrates advanced audio processing features such as programmable gain, digital filters, automatic gain control (AGC), voice activity detection (VAD), and an integrated PLL. It communicates through an I²C control interface and supports I²S, TDM, and Left-Justified (LJ) digital audio formats, making it ideal for smart speakers, conferencing systems, IP cameras, and other high-performance audio acquisition systems. Key Features High-performance 2-channel audio ADC Supports 2 analog microphone/line inputs or 4 digital PDM microphone inputs 104 dB dynamic range (DR) and –95 dB THD+N Sampling rates from 8 kHz to 768 kHz Programmable microphone gain from 0 dB to 42 dB Digital volume control from –100 dB to +27 dB Integrated programmable HPF, biquad filters, and low-latency filter modes Built-in Automatic Gain Control (AGC) and Voice Activity Detection (VAD) Integrated audio PLL and programmable microphone bias supply Supports I²S, TDM, and Left-Justified (LJ) audio interfaces Configurable for 1.8 V or 3.3 V supply operation Available in a compact 20-pin WQFN (RTE) package Operating temperature range: –40°C to +105°C #AudioADC #TexasInstruments #TAA3020 #HighPerformanceADC #I2S #TDM #PDMMicrophone #AudioProcessing #AGC #VAD #EmbeddedAudio #ProfessionalAudio

IC RF TxRx + MCU Cellular CDMA, GSM, HSPA, LTE, TD-SCDMA, WCDMA 100kHz ~ 3.8GHz 261-SMD Module The LMS7002M is a Field Programmable RF (FPRF) transceiver that can both transmit and receive radio signals over a very wide frequency range. It integrates most of the RF front-end and baseband processing functions into a single chip, minimizing the need for external components. Frequency range: 100 kHz to 3.8 GHz Architecture: Dual transceiver (2 TX + 2 RX) supporting 2×2 MIMO Bandwidth: Up to ~120–160 MHz RF bandwidth depending on configuration Technology: CMOS-based for low cost and power consumption Integrated blocks: ADCs & DACs (12-bit) LNAs and PA drivers Mixers, PLL synthesizers Filters and gain control On-chip DSP and microcontroller Transmit path: Digital baseband → DAC → filtering → RF upconversion → output Receive path: RF input → LNA → downconversion → filtering → ADC → digital processing This zero-IF (direct conversion) architecture simplifies design and supports wideband operation. #CommonPartsLibrary #IntegratedCircuit #LMS7002