Raspberrypi Pico-based sampler, sequencer + drum machine w/ an embedded speaker, Adafruit I2S amplifier and momentary step switches, evoking the tr808 synthesizer ⁠

A buck boost converter that can be powered from a Li-Ion battery and output 3.3V @ 500mA. Powered by the TPS63051YFFR and in the same package as a standard Adafruit buck converter. Expect to squeeze around 5-10% SoC from a typical Li-Ion battery. Input Voltage Range: 2.5V to 5.5V Assembled at pcbway.com

Adafruit MAX31865 RTD PT100 or PT1000 Amplifier #MAX31865 #Adafruit #Amplifier #PT100 #PT1000 #referenceDesign #project

Display of Adafruit-based components

Raspberrypi Pico-based sampler, sequencer + drum machine w/ an embedded speaker, Adafruit I2S amplifier and momentary step switches, evoking the tr808 synthesizer ⁠

A tiny microcontroller board, built around the Atmel ATtiny85, a little chip with a lot of power. We wanted to design a microcontroller board that was small enough to fit into any project, and low cost enough to use without hesitation. Perfect for when you don't want to give up your expensive dev-board and you aren't willing to take apart the project you worked so hard to design. It's our lowest-cost arduino-IDE programmable board!

Vertical USB & I2C Interface Module – Organized Power/Data Terminal Block

El BNO055 es un sensor que incluye todos los sensores necesarios con compensación de temperatura así como un potente microcontrolador ARM Cortex-M0 que procesa y realiza todos los cálculos matemáticos, todo eso en un solo chip.

Featherwing template with pre-loaded nRF52 Bluefruit feather. #template #feather #wing #adafruit

The Micro is a microcontroller board based on the ATmega32U4 (datasheet), developed in conjunction with Adafruit. It has 20 digital input/output pins (of which 7 can be used as PWM outputs and 12 as analog inputs), a 16 MHz crystal oscillator, a micro USB connection, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a micro USB cable to get started. It has a form factor that enables it to be easily placed on a breadboard. The Micro board is similar to the Arduino Leonardo in that the ATmega32U4 has built-in USB communication, eliminating the need for a secondary processor. This allows the Micro to appear to a connected computer as a mouse and keyboard, in addition to a virtual (CDC) serial / COM port.

Adafruit MAX31865 RTD PT100 or PT1000 Amplifier #MAX31865 #smartHome #sensor #temperatureSensor #temperature #Amplifier #PT100 #PT1000 #referenceDesign #template

A buck boost converter that can be powered from a Li-Ion battery and output 3.3V @ 500mA. Powered by the TPS63051YFFR and in the same package as a standard adafruit buck converter . Input Voltage range : 2.5V to 5.5V

Raspberrypi Pico-based sampler, sequencer + drum machine w/ an embedded speaker, Adafruit I2S amplifier and momentary step switches, evoking the tr808 synthesizer ⁠

PowerBoost 500C is the perfect power supply for your portable project! With a built-in battery charger circuit, you'll be able to keep your project running even while recharging the battery! This little DC/DC boost converter module can be powered by any 3.7V LiIon/LiPoly battery, and convert the battery output to 5.2V DC for running your 5V projects.

Adafruit 2.8 Inch ILI9341 240x320 SPI TFT LCD Display Touch Panel SPI Serial Port Module #display #lcd

This project is a communication device designed with Adafruit's 3857 Microcontroller (U1) and Hoperf's RFM95W-915S2 RF module (U2). The microcontroller interfaces with the RF module via SPI protocol for wireless data transmission. The project also includes a capacitor (C1) and an SMA connector (J1). #LoRa #IoT #project #M4 #Adafruit

Welcome to your new project. Imagine what you can build here.

A sensor to sense the presence of different gasses in the air we breathe.

The DRV2605 from TI is a fancy little motor driver. Rather than controlling a stepper motor or DC motor, its designed specifically for controlling haptic motors - buzzers and vibration motors. Normally one would just turn those kinds of motors on and off, but this driver has the ability to have various effects when driving a vibe motor. For example, ramping the vibration level up and down, 'click' effects, different buzzer levels, or even having the vibration follow a musical/audio input.

TPS61090 - DC/DC, Step Up 1, Non-Isolated Outputs Evaluation Board #PowerBoost #Charger #EvaluationBoard #module

Welcome to your new project. Imagine what you can build here.

A buck boost converter that can be powered from a Li-ion battery and ouput 3.3V @500mA. Powered by the TPS63051YFFR and in the same package as a standard ADAFRUIT buck converter. Input Voltage Range: 2.5 to 5.5 Voltage.

This is an ESP8266-12E powered at-home weather station. It connects to an Adafruit anemometer (https://www.adafruit.com/product/1733), WiFi, and multiple sensors to give various bits of data.

A buck boost converter that can be powered from a Li-Ion battery and output 3.3V @ 500mA. Powered by the TPS63051YFFR and in the same package as a standard Adafruit buck converter. Expect to squeeze around 5-10% SoC from a typical Li-Ion battery. Input Voltage Range: 2.5V to 5.5V

Featherwing template with pre-loaded nRF52 Bluefruit feather. #template #feather #wing #adafruit