This project is a reference design based on the ISL6292, a single cell Li-Ion battery charger. It manages the power between an external power source (VIN), a Li-Ion battery (BAT), and a system power rail (SYS). Key features include power-path management, battery thermistor monitoring, and charge status indication. #Module #ISL6292 #ReferenceDesign #charger #BatteryManagement #reusable #module #bms #renesas #sublayout

This is a module boost DC-DC Regulator with 12V 0.3A(1.2A) output and 5V input voltage #ti #ledpower #led #boost #reusable #module #powermanagement #texas-instruments #sublayout

This is an ESP32-C3 module based on the manufacturer's recommendations with a uFL SMD antenna and USB C on board #WiFi #ESP32-C3 #IoT #reusable #module #simple-embedded #espressif #sublayout

This is a QRE1113 opto-reflective sensor module, using a 47K pull-up resistor (R2) and a 100 Ohm resistor (R1). It includes a 1µF capacitor (C1) for stability and attaches to a JST connector (J1) for easy interfacing. Power is provided via VCC, with the output signal (OPTO_OUT) fed back. #OpticalSensor #industrialSensing #reusable #module #industrialsensing #onsemi #sublayout

This project is a plant care system that uses an ESP32-S3-MINI-1U-N8 microcontroller to automate plant care tasks. This system includes three Songle relays, multiple resistors, capacitors, and transistors, all powered at 3.3V, 5V, or 12V. It also incorporates a USB Type-C connector. #referenceDesign #edge-computing #reusable #module #edge-computing #edgeComputing #espressif #sublayout #iot #iot #ESP32 #relay

This is a boost module based on ADP1613 step-up dc-to-dc switching converter with a 15V output #dcdc #power #boost #15V #reusable #module #powermanagement #analogdevices #sublayout

This is a module of buck converter based on LT3991 with output voltage 3.3V #dcdc #power #ad #3V3 #reusable #module #powermanagement #analogdevices #sublayout

This is a module of ESP32-S3-WROOM-1U. The board has 3 LEDs, USB C for firmware, EN and BOOT buttons, and 2 IO connectors for development #IoT #WiFi #MCU #RF #ESP32 #part #reusable #module #simple-embedded #espressif #sublayout

Your microcontroller probably has an ADC (analog -> digital converter) but does it have a DAC (digital -> analog converter)??? Now it can! This breakout board features the easy-to-use MCP4725 12-bit DAC. Control it via I2C and send it the value you want it to output, and the VOUT pin will have it. Great for audio/analog projects, such as when you can't use PWM but need a sine wave or adjustable bias point. #Sublayout #DAC #ADC #MCP4725

This is a module of high efficiency synchronous step-down dc-dc converters optimized for battery powered portable applications. #power #dcdc #ti #buck #reusable #module #powermanagement #texas-instruments #sublayout

This is a module of a buck converter based on LTC3406 with 1.2V 0.6A output #dcdc #ad #power #1V2 #reusable #module #powermanagement #analogdevices #sublayout

This is a smart blind control system module designed to automate the operation of window blinds. It utilizes an ESP32 microcontroller for managing control signals and an A4988 stepper motor driver to control blinds' movement. It also includes USB interfacing and LED feedback. #reusable #module #edge-computing #edgeComputing #espressif #sublayout #blind #DC #motor #servo #esp32

This is a module of ESP32-C3-MINI-1U based on the manufacturer's recommendations. On board we have an ESP module, USB C for firmware, 2 connectors with IOs and RGB LED #ESP32 #WiFi #LED #IoT #BLE #ARM #reusable #module #simple-embedded #espressif #sublayout

Life has its ups and downs, so why not measure them? The MPL3115A2 is a MEMS pressure sensor that provides Altitude data to within 30cm (with oversampling enabled). The sensor outputs are digitized by a high resolution 24-bit ADC and transmitted over I2C, meaning it's easy to interface with most controllers. Pressure output can be resolved with output in fractions of a Pascal, and Altitude can be resolved in fractions of a meter. The device also provides 12-bit temperature measurements in degrees Celsius. #Sublayout #Submodule #Altitude #PressureSensor #MPL3115A2

This is a ESP32-C6-WROOM-1 module built on manufacture recommendations. Here is on board an ESP32-H2-MINI-1 module, RESET and BOOT buttons, RGB LED, and 2 connectors for IOs #ESP32 #WiFi #IoT #ARM #reusable #module #simple-embedded #espressif #sublayout

This project is a LoRa temperature sensor module. It uses the RP2040 microcontroller and a SHT31 temperature sensor and also RFM95 for LoRa communication #LoRa #module #reusable #simple-embedded #raspberrypi #sublayout

This is the LSM9DS1TR IMU Module. This reference design has a basic I2C circuit for communication built according to the manufacturer's recommendations #IMU #LSM9DS1TR #I2C #reusable #module #imu #stm #sublayout

This is a light-sensitive LED reference design featuring an STM32L031F4P6 microcontroller. It interfaces with a TEMT6000X01 light sensor and controls a multi-colored LED. The system also has a user button and UART for communication, and regulators to manage power supply. #referenceDesign #reusable #module #simple-embedded #light-sensitive #module #sublayout

This is a BQ24070 li ion charging module created according to the manufacturer's recommendations. The board has a connector with pins for setting modes and 3 power connectors #reusable #module #bms #texas-instruments #sublayout