General Purpose Amplifier 2 Circuit 8-PDIP #CommonPartsLibrary #IntegratedCircuit #Op-Amp #Amplifier

An xtal electronic oscillator circuit that uses the mechanical resonance of a vibrating crystal of piezoelectric material to create an electrical signal with a precise frequency.

270V 4.5kA Varistor 1 Circuit Through Hole Disc 14mm #commonpartslibrary #circuitprotection #varistor #TVS #tht #MOVs

Digital Potentiometer 100k Ohm 4 Circuit 129 Taps SPI Interface 20-TSSOP #CommonPartsLibrary #IntegratedCircuit #Data-Acquisition #Digital-Potentiometer #WiperLock™

Circuit Board Hardware - PCB TEST POINT, PC Test Point, Miniature Phosphor Bronze Silver Plating Surface Mount Mounting Type #CommonPartsLibrary #Test-point

Voltage Level Translator Bidirectional 1 Circuit 8 Channel 100Mbps 20-TSSOP #CommonPartsLibrary #IntegratedCircuit #Logic #Translator #Level-Shifter #TXB0108

J-FET Amplifier 1 Circuit 8-PDIP #CommonPartsLibrary #IntegratedCircuit #Linear #Amplifier #OP-Amp #TL081

General Purpose Amplifier 1 Circuit 8-PDIP #CommonPartsLibrary #IntegratedCircuit #OP-AMP #Amplifier #UA741

Digital Potentiometer 10k Ohm 1 Circuit 256 Taps SPI Interface 8-SOIC #CommonPartsLibrary #IntegratedCircuit #DataAcquisition #DigitalPotentiometer #MCP41010

General Purpose Amplifier 4 Circuit 14-SOIC #CommonPartsLibrary #IntegratedCircuit #Linear #Amplifier #OP-Amp #Instrumentation #Buffer-Amp #LM324

Instrumentation Amplifier 1 Circuit Rail-to-Rail 8-VSSOP #commonpartsLibrary #integratedcircuit #opamp

Instrumentation Amplifier 1 Circuit 8-PDIP #CommonPartsLibrary #IntegratedCircuit #Linear #Amplifier #Op-Amp #INA128

General Purpose Amplifier 2 Circuit 8-SOIC #commonpartslibrary #integratedcircuit #linearamplifier #opamp

The NE555 devices are precision timing circuits capable of producing accurate time delays or oscillation. In time-delay or monostable operating modes, the timed interval is controlled by a single external resistor and capacitor network. In the astable mode of operation, the frequency and duty cycle are controlled independently with two external resistors and a single external capacitor. Each timer has a trigger level equal to approximately one-third of the supply voltage and a threshold level equal to approximately two-thirds of the supply voltage. These levels can be altered by use of the control voltage pin (CONT). When the trigger input (TRIG) is less than the trigger level, the flip-flop is set and the output goes high. If TRIG is greater than the trigger level and the threshold input (THRES) is greater than the threshold level, the flip-flop is reset and the output is low. The reset input (RESET) overrides all other inputs and is used to initiate a new timing cycle. If RESET is low, the flip-flop is reset and the output is low. Whenever the output is low, a lowimpedance path is provided between the discharge pin (DISCH) and the ground pin (GND). Tie all unused inputs to an appropriate logic level to prevent false triggering. The output circuit is capable of sinking or sourcing current up to 200mA. Operation is specified for supplies of 5V to 15V. With a 5V supply, output levels are compatible with TTL inputs. Features - Timing from microseconds to hours - Astable or monostable operation - Adjustable duty cycle - TTL-compatible output can sink or source up to 200mA - On products compliant to MIL-PRF-38535, all parameters are tested unless otherwise noted. Applications - Pulse-shaping circuits - Missing-pulse detectors - Pulse-width modulators - Pulse-position modulators - Sequential timers - Pulse generators -F requency dividers - Industrial controls

Current Sense Amplifier 1 Circuit Rail-to-Rail SOT-23-5 #commonpartslibrary #integratedcircuit #linearamplifier #opamp

3 Circuit 0.325" (8.26mm) Barrier Block Connector Screws with Captive Plate

General Purpose Amplifier 4 Circuit Rail-to-Rail 14-TSSOP #CommonPartsLibrary #IntegratedCircuit #Amplifier #OpAmp #LMV324

USB-C (USB TYPE-C) USB 3.2 Gen 2 (USB 3.1 Gen 2, Superspeed + (USB 3.1)) Receptacle Connector 24 Position Board Edge, Cutout; Surface Mount; Through Hole, Right Angle This component is a precision electronic device designed for integration into a wide range of circuit applications. It provides reliable electrical and mechanical performance while maintaining compatibility with standard PCB assembly processes. The device is intended for use in systems requiring stability, durability, and consistent operation across varying environmental conditions. Key Features High reliability and stable operation Compact, industry-standard footprint Compatible with automated assembly processes Lead-free and environmentally compliant Designed for long-term use Applications Consumer electronic devices Industrial control equipment Embedded systems and controllers Power and signal management circuits General-purpose electronic assemblies Electrical Characteristics (Typical – verify with manufacturer datasheet) Voltage rating: To be specified Current rating: To be specified Power rating: To be specified Tolerance or accuracy: To be specified Relevant electrical parameter (resistance, impedance, gain, etc.): To be specified Mechanical Characteristics Package type: To be specified Mounting method: Surface mount or through-hole Dimensions: To be specified Terminal style: To be specified Environmental Specifications Operating temperature range: Typically suitable for standard industrial conditions Storage temperature range: Extended range for safe storage Humidity tolerance: Suitable for non-condensing environments Compliance and Standards Compliant with environmental regulations Compatible with industry manufacturing standards #commonpartslibrary #connector #usb #typec