Bipolar (BJT) Transistor NPN 40V 200 mA 300MHz 300 mW Surface Mount SOT-23-3 (TO-236) The MMBT3904LT1G is a general-purpose NPN bipolar junction transistor designed for switching and amplification applications. It is housed in a compact SOT-23 surface-mount package, making it suitable for high-density PCB designs. This transistor is widely used in low-power signal processing, digital switching, and analog amplification circuits due to its reliable performance and fast switching characteristics. Key Features General-purpose NPN transistor Compact SOT-23 surface-mount package Fast switching speed Low saturation voltage Suitable for low-current and low-power applications High reliability and stability Pb-free, Halogen-free, and RoHS compliant Electrical Characteristics (Typical @ 25°C unless otherwise specified) Collector-Emitter Voltage (VCEO): 40 V Collector-Base Voltage (VCBO): 60 V Emitter-Base Voltage (VEBO): 6 V Collector Current (IC): 200 mA (max) DC Current Gain (hFE): 100 – 300 Collector-Emitter Saturation Voltage (VCE(sat)): 0.2 V (typ) Transition Frequency (fT): ~300 MHz Absolute Maximum Ratings Collector Current (Continuous): 200 mA Power Dissipation: ~225 mW Junction Temperature: +150°C (max) Operating Temperature Range: -55°C to +150°C Storage Temperature Range: -55°C to +150°C Mechanical Characteristics Package Type: SOT-23 (TO-236AB) Mounting Type: Surface Mount Number of Pins: 3 Marking Code: Dependent on lot/manufacturer marking Applications General-purpose switching circuits Signal amplification Digital logic interfacing LED drivers and small load switching Audio and RF signal processing #CommonPartsLibrary #TransistorBJT #MMBT2222

Magnitude Comparator Bit Active High Output A<B, A=B, A>B 16-PDIP #CommonPartsLibrary #IntegratedCircuit #Logic #Comparator #74LS85

The NE555 devices are precision timing circuits capable of producing accurate time delays or oscillation. In time-delay or monostable operating modes, the timed interval is controlled by a single external resistor and capacitor network. In the astable mode of operation, the frequency and duty cycle are controlled independently with two external resistors and a single external capacitor. Each timer has a trigger level equal to approximately one-third of the supply voltage and a threshold level equal to approximately two-thirds of the supply voltage. These levels can be altered by use of the control voltage pin (CONT). When the trigger input (TRIG) is less than the trigger level, the flip-flop is set and the output goes high. If TRIG is greater than the trigger level and the threshold input (THRES) is greater than the threshold level, the flip-flop is reset and the output is low. The reset input (RESET) overrides all other inputs and is used to initiate a new timing cycle. If RESET is low, the flip-flop is reset and the output is low. Whenever the output is low, a lowimpedance path is provided between the discharge pin (DISCH) and the ground pin (GND). Tie all unused inputs to an appropriate logic level to prevent false triggering. The output circuit is capable of sinking or sourcing current up to 200mA. Operation is specified for supplies of 5V to 15V. With a 5V supply, output levels are compatible with TTL inputs. Features - Timing from microseconds to hours - Astable or monostable operation - Adjustable duty cycle - TTL-compatible output can sink or source up to 200mA - On products compliant to MIL-PRF-38535, all parameters are tested unless otherwise noted. Applications - Pulse-shaping circuits - Missing-pulse detectors - Pulse-width modulators - Pulse-position modulators - Sequential timers - Pulse generators -F requency dividers - Industrial controls

Flip Flop 2 Element D-Type 1 Bit Positive Edge 14-SOIC (0.154", 3.90mm Width) #CommonPartsLibrary #IntegratedCircuit #Logic #Flip-Flop #74HC74

Flip Flop 1 Element D-Type 1 Bit Positive Edge 8-XFDFN #CommonPartsLibrary #IntegratedCircuit #Logic #FLIP-FLOP #74LVC

Automotive, 60-V, 6-A, 30-mΩ, one-channel smart high-side switch with adjustable current limit TPS1HTC30-Q1 is a single-channel, smart high-side switch, with integrated NMOS power FET and charge pump, designed to meet the requirements of 24-V automotive battery systems. The low RON(30 mΩ) minimizes device power dissipation driving a wide range of output load current up to 6-A DC, and the 60- V DC operating range improves system robustness. The device integrates protection features such as thermal shutdown, output clamp, and current limit. These features improve system robustness during fault events such as short circuit. TPS1HTC30-Q1 implements an adjustable current limiting circuit that improves the reliability of the system by reducing inrush current when driving large capacitive loads and minimizing overload current. The device also provides an accurate load current sense that allows for improved load diagnostics such as overload and open-load detection enabling better predictive maintenance. TPS1HTC30-Q1 is available in a small 14-pin, 4.40- mm × 5.0-mm HTSSOP leaded package with 0.65- mm pin pitch minimizing the PCB footprint. • Single-channel smart high-side power switch for 24-V automotive systems with full diagnostics • Wide operating voltage range: 6 V to 60 V – OVP protection: 66 V • Low RON: 30-mΩ typical, 55-mΩ maximum • Low standby current: < 0.5 µA • Low quiescent current (Iq): < 2 mA • Improve system level reliability through adjustable current limiting – Current limit: 2 A –16 A • Accurate current sensing: ±4% at 1 A • Protection – Overload and short-circuit protection – Integrated inductive discharge clamp – Undervoltage lockout (UVLO) protection – Loss of GND, loss of supply protection – Reverse battery protection with external components • Diagnostics – On and off state output open-load and short-tobattery detection – Overload and short to ground detection – Absolute and relative thermal shutdown detection • Functional Safety-Capable – Documentation available to aid functional safety system design • Operating junction temperature: –40 to 125°C • Input control: 1.8-V, 3.3-V and 5-V logic compatible • Integrated fault sense voltage scaling for ADC protection • Qualifications – AEC-Q100 qualified for automotive applications • Temperature grade 1: –40°C to +125°C, TA • 14-pin thermally-enhanced TSSOP package TPS1HTC30AQPWPRQ1 #CommonPartsLibrary #IntegratedCircuit

OR Gate IC 4 Channel 14-PDIP #CommonPartsLibrary #IntegratedCircuit #Logic #74HC32

NAND Gate IC 4 Channel 14-SO #CommonPartLibrary #IntegratedCircuits #Logic #Gate #Inverter

Decoder/Demultiplexer 1 x 3:8 16-PDIP #commonpartslibrary #integratedcircuit #logic #decoder #demultiplexer

Buffer, Non-Inverting 1 Element 1 Bit per Element Push-Pull Output SC-70-5 #logic #74AUC1G17 #74AUC

Flip Flop 2 Element JK Type 1 Bit Negative Edge 16-DIP (0.300", 7.62mm) #CommonPartsLibrary #IntegratedCircuit #Logic #Flip-Flop #74LS112

Logic Output Optoisolator 10MBd Open Drain 5300Vrms 2 Channel 15kV/µs CMTI 8-SMD #commonpartsLibrary #isolator

Flip Flop 2 Element D-Type 1 Bit Positive Edge 14-SOIC (0.154", 3.90mm Width) #CommonPartsLibrary #IntegratedCircuit #Logic #Flip-Flop # 74AC74

Decoder/Demultiplexer 1 x 2:4 16-PDIP #CommonPartsLibrary #IntegratedCircuit #Logic #Signal-Switch #Multiplexer #Decoder #74LS139

Flip Flop 2 Element D-Type 1 Bit Positive Edge 14-DIP (0.300", 7.62mm) #CommonPartsLibrary #IntegratedCircuit #Logic #Flip-Flop

Inverter IC 6 Channel 14-TSSOP #CommonPartsLibrary #IntegratedCircuit #Logic #Inverter #74AC04

555 Type, Timer/Oscillator (Single) IC 2.1MHz 8-SOIC The TLC555IDR is a low-power CMOS timer device designed as a functional replacement for the standard bipolar 555 timer while providing significantly reduced supply current and improved operating efficiency. The device supports both astable and monostable operating modes and is commonly used for timing generation, pulse shaping, oscillation, PWM generation, delay circuits, and frequency generation applications. The CMOS architecture enables low power consumption, rail-to-rail output capability, and stable timing performance over a wide operating voltage range. The device is suitable for battery-powered systems, portable electronics, industrial controls, instrumentation, consumer products, and embedded electronic designs. The TLC555IDR is supplied in a compact SOIC surface-mount package intended for automated PCB assembly and space-constrained applications. Electrical Characteristics CMOS low-power timer architecture Functional equivalent to standard 555 timer devices Wide operating supply voltage range Low quiescent supply current High input impedance Rail-to-rail output swing capability Stable threshold and trigger levels Compatible with TTL and CMOS logic levels Capable of astable and monostable operation Adjustable duty cycle and frequency operation High output drive capability for direct interfacing Low noise and improved switching performance compared to bipolar 555 timers Functional Features Precision timing generation Oscillator and clock generation Pulse-width modulation support One-shot pulse generation Delay timer implementation Missing pulse detection Frequency divider implementation Sequential timing control LED flashing and tone generation PWM motor and power control applications Package Information Surface-mount SOIC package Standard tape-and-reel packaging format Compact footprint for automated assembly RoHS compliant device construction Environmental and Operating Conditions Industrial operating temperature range ESD protection handling required Suitable for commercial and industrial embedded systems Designed for low-power electronic applications Typical Applications Timer circuits Pulse generators Oscillators PWM controllers LED flashers Alarm and tone generators Frequency generators Power management timing Embedded control systems Portable battery-powered electronics #commonpartslibrary #integratedcircuit #timer #oscillator