Composed of two simulated separate circuits that demonstrate how step up and step down transformers work.

Composed of two simulated separate circuits that demonstrate how step up and step down transformers work.

Welcome to your new project. Imagine what you can build here.

The main board for UbiHouse Mini. Controlling 2 DC motors, 1 LED, 2 RGB LED, 1 humidity and temperature sensor (DHT22), 1 water level sensor with a ESP32 S3 Mini

This project is a reference design for the VL53L0X time-of-flight ranging sensor from STMicroelectronics. The circuit includes a voltage regulator, level shifting for I2C communication, and connections for various GPIOs, all catering to proper operation of the sensor. #industrialSensing #ReferenceDesign

This project is a Sample and Hold Circuit. It utilizes an operational amplifier (UA741CDT), a capacitor, resistors, a Q2 junction transistor, and connectors. The circuit captures a voltage level at a specific moment and sustains this level until instructed otherwise. #project

This project combines one soil sensor (resistive or capacetive), one 5V pump in a water tank and a floating switch to detect the water level. Depending on the soil measurment and the configured nominal value the pump can be controlled while the floating switch prevents the pump from running dry. All configurations can be controlled via MQTT.

This board measure battery voltage and shows a current battery level. Based on ATTINY13 MCU and compatible with Arduino IDE. J1 is 6-Pin AVR ISP Connector

A simple WLED controller utilizing an ESP32 and configured for 4 channels of output. Utilizes a level shifter.

Light Detection: The LDR detects the ambient light level. When it is dark, the resistance of the LDR is high, resulting in a higher voltage at the inverting input (pin 2) of the op-amp. Comparison: The op-amp compares the voltage at pin 2 with the reference voltage set at pin 3 by the potentiometer (R3). If the voltage at pin 2 is higher than the reference voltage at pin 3 (indicating darkness), the op-amp output goes high. Transistor Activation: The high output from the op-amp turns on the transistor (Q1) by providing base current through R4. Relay Activation: When Q1 is turned on, current flows through the relay coil, energizing it and closing the relay contacts. Lamp Operation: The closed relay contacts complete the AC circuit, allowing current to flow and turning on the lamp (LA1). Light Detection (Daytime): When it is light, the resistance of the LDR decreases, resulting in a lower voltage at pin 2 of the op-amp. If this voltage is lower than the reference voltage at pin 3, the op-amp output goes low, turning off Q1, de-energizing the relay, and turning off the lampWelcome to your new project. Imagine what you can build here.

Low-voltage logic-only CERILUME Phase 1 LED controller using an Arduino Nano ESP32 plug-in module, 5V logic level shifting for WS2812/SK6812 data, microphone input header, and labeled test pads. LED power distribution and high-current switching are intentionally out of scope.

This project is a reference design for a TSL25911FN-based sensor module, with level-shifted I2C communication. It includes a 3.3V regulator, I2C level shifter, filter capacitors, pull-up resistors, and JST connectors for interfacing. #project #Template #projectTemplate #sensor #light #industrialSensing #referenceDesign #template #reference-design #polygon

The HOTCHIP HT4936S is a sophisticated mobile power management integrated circuit designed by Hotchip, optimized for portable power solutions that require efficient charging and power management capabilities. This advanced component integrates features for charging and discharging through a common port, automatic load detection for boost startup and shutdown, four-light battery level indication, and a low battery alert functionality. The HT4936S stands out for its ability to manage 1A input/output with minimal external components, leveraging synchronous rectification to enhance efficiency and reduce thermal footprint. Additionally, it supports a versatile charging protocol accommodating both 4.20V and 4.35V batteries, and is packaged in a compact SOP16 form factor, ensuring a low-cost, space-efficient solution for a wide range of mobile power applications including power banks, backup power supplies, and lithium battery chargers. It incorporates protection features against battery overcharge, over-discharge, and thermal overload, thereby ensuring reliable operation across a range of conditions. Furthermore, the HT4936S facilitates direct LED drive and includes an NTC thermistor input for temperature monitoring, making it an all-encompassing solution for power management in consumer electronics.

Coolant level sensor

Glucose meter is a medical device that determines the approximate concentration of glucose in the blood. A strip containing chemicals that react with glucose in the drop of blood is used for each measurement. Op Amp Circuit description: LMC6484 IC_D is an integrator circuit. LMC6484 IC_A and IC_C are configured as unity gain buffer amplifiers. LMC6484 IC1B is configured as a trans impedance amplifier. Arduino is used for processing of the measured glucose level. The Arduino use the built in ADC module for analog to digital conversion. Further, the Arduino helps to detect the strip also.

Glucose meter is a medical device that determines the approximate concentration of glucose in the blood. A strip containing chemicals that react with glucose in the drop of blood is used for each measurement. Op Amp Circuit description: LMC6484 IC_D is an integrator circuit. LMC6484 IC_A and IC_C are configured as unity gain buffer amplifiers. LMC6484 IC1B is configured as a trans impedance amplifier. Arduino is used for processing of the measured glucose level. The Arduino use the built in ADC module for analog to digital conversion. Further, the Arduino helps to detect the strip also.

This project is a reference design for the VCNL3040 sensor interfaced via I2C. It includes a VCNL3040 ambient light sensor, a voltage regulator (AP2112K-3.3TRG1), an I2C level shifter using BSS138 MOSFETs, and necessary support components. Circuit interfaces through a JST connector. All components are powered by a 3.3V power source. #referenceDesign #industrialsensing #vishay #template #reference-design

The PAM8610, manufactured by Power Analog Microelectronics, is a high-performance, 10W (per channel) stereo class-D audio amplifier featuring DC volume control. This component is designed to deliver low THD+N (0.1%), low EMI, and high efficiency (>90%), making it ideal for high-quality sound reproduction in a variety of applications such as flat monitor/LCD TVs, multi-media speaker systems, DVD players, game machines, boomboxes, and musical instruments. Operating off a 7V to 15V supply, the PAM8610 distinguishes itself with its 32-step DC volume control ranging from -75dB to 32dB, shutdown/mute/fade functions, and comprehensive protection against overcurrent, thermal, and short-circuit conditions. Its low quiescent current, pop noise suppression, and minimal external component requirement further enhance its appeal for compact and efficient audio solutions. The PAM8610 is available in a compact 40-pin QFN 6mm*6mm package, ensuring a small footprint for space-constrained applications. Compliance with RoHS standards underscores its environmental consideration. With its advanced features and high integration level, the PAM8610 offers a compelling option for designers seeking to incorporate robust audio amplification with fine-grained volume control in their electronic projects.

Glucose meter is a medical device that determines the approximate concentration of glucose in the blood. A strip containing chemicals that react with glucose in the drop of blood is used for each measurement. Op Amp Circuit description: LMC6484 IC_D is an integrator circuit. LMC6484 IC_A and IC_C are configured as unity gain buffer amplifiers. LMC6484 IC1B is configured as a trans impedance amplifier. Arduino is used for processing of the measured glucose level. The Arduino use the built in ADC module for analog to digital conversion. Further, the Arduino helps to detect the strip also.

Production-intent ESP32-C6 controller for WS2812B/WS2815 addressable LED strips with 5V/10A input protection, strip high-side switching, 5V data level shifting, user buttons, and antenna keepout requirements.

Compact USB dongle PCB for Midea air conditioners based on the mideahvac-dongle architecture, using an ESP32-C6 module, 5V UART level shifting, WS2812B status LED, USB-A appliance connector, and USB-C programming/power.

Low-voltage logic-only CERILUME Phase 1 LED controller using an Arduino Nano ESP32 plug-in module, 5V logic level shifting for WS2812/SK6812 data, microphone input header, and labeled test pads. LED power distribution and high-current switching are intentionally out of scope.

Premium dual-PCB ESP32 smart water level controller with isolated high-voltage power/motor board, low-voltage IoT logic board, level sensing, dry-run/voltage/current protection, TFT UI, MQTT connectivity, RTC logging, and industrial surge protection.

Production-ready ESP32-DEVKITC-32UE festival carousel horse LED controller schematic with organized Power, ESP32 + Level Shifter + LEDs, Inputs, and DMX + OLED blocks.

4-layer dual PCA9685 servo controller with Raspberry Pi 5, STM32 Nucleo, TXS0102 I2C level shifting, 6.0V/20A servo rail, and 5.1V logic rail.