RJ45 Footprint Audit


Exported 2 file exports
2250506-1.kicad_pcb
KICAD export
2250506-1-gerbers.zip
GERBER export
Result: conditionally qualified — drilling remains a hard blocker
The active source part is read-only, so I made no mutations and published no new version. Current source version remains HEAD, latest project commit #c6f09816.
Drawing-to-footprint comparison
Authoritative drawing: Bel 0826-1X1T-HS-F, recommended footprint shown from the component side, units inch [mm], .XXX footprint tolerance ±0.004 in.

Table


FeatureBel drawingActual read-backAssessment
Pins 1–62.032 mm pitch, Y=15.24ExactPass
Pins 7–122.032 mm pitch, Y=17.78ExactPass
Row separation2.54 mmExactPass
Pins 13–16X=±5.59; Y=6.59/8.13ExactPass
Pins 17–20Y=20.32; X=±6.096/±3.556ExactPass
Shield S1/S2X=±8.065, Y=−3.18ExactPass
Locating postsX=±6.35, Y=0ExactPass
Electrical pads2020Pass
Shield pads22Pass
Locating holes22Pass
Pin-1 markingRectangular pin 1PresentPass
Copper layersTop and Bottom annular layersPresentPass
Body outline16.38 × 33.02 mm nominalFootprint outline matchesPass
Jack/front face−Y end, approximately Y=−22.1 mmMatches outline/model orientationPass
Maximum height13.61 mm nominalModel exists, but package-height read-back unavailableConditional
LED polarity17−/18+ yellow; 19+/20− orange and 19−/20+ greenTerminal mapping preservedPass
The footprint also correctly preserves all 22 schematic-terminal mappings.
Hard blocker for carrier J3/J4
Flux read-back exposes pad copper sizes but not the baked drill diameters or plated/NPTH classification. Therefore J3/J4 are not fabrication-qualified yet. Required drawing hole classes are:
  • Pins 1–16: Ø0.89 mm, +0.13/−0.00 mm
  • Pins 17–20: Ø1.02 mm, +0.13/−0.00 mm
  • S1/S2: Ø1.57 mm
  • Two locating posts: Ø3.25 mm, NPTH
I did not apply or recommend blind overrides because the existing drill values cannot be read back, and overwriting potentially correct drills would not be a proven repair.
Exact local-override procedure
For each placed J3 and J4, inspect its descendant pad UIDs, then create selector-based rulesets with !important:
  • Pins 1–16: holeSize=0.89mm, padHoleType=STD
  • Pins 17–20: holeSize=1.02mm, padHoleType=STD
  • S1/S2: holeSize=1.57mm, padHoleType=STD
  • Two unnumbered locating holes: holeSize=3.25mm, padHoleType=HOLE
Do not alter positions, pad copper sizes, orientation, or terminal mapping. The exact executable selectors cannot be safely supplied until J3/J4’s actual descendant node UIDs are available.
No proven coordinate, pitch, count, layer, polarity, or orientation defect was found. No source repair was justified, and no version was published.

~
Pin Number
18
~
Pin Number
17
~
Pin Number
19
SHIELD_S1
Pin Number
S1
~
Pin Number
20
VC4
Pin Number
16
Pin #
Name
Type
Section
Pin Group
Orientation
Order
Sub-symbol
Pin Description
1
TRCT3
Passive
PHY-side transformer center tap, data pair 3
2
TRD3-
Passive
PHY-side transformer data pair 3 negative
3
TRD3+
Passive
PHY-side transformer data pair 3 positive
4
TRD2+
Passive
PHY-side transformer data pair 2 positive
5
TRD2-
Passive
PHY-side transformer data pair 2 negative
6
TRCT2
Passive
PHY-side transformer center tap, data pair 2
7
TRCT4
Passive
PHY-side transformer center tap, data pair 4
8
TRD4+
Passive
PHY-side transformer data pair 4 positive
9
TRD4-
Passive
PHY-side transformer data pair 4 negative
10
TRD1-
Passive
PHY-side transformer data pair 1 negative
11
TRD1+
Passive
PHY-side transformer data pair 1 positive
12
TRCT1
Passive
PHY-side transformer center tap, data pair 1
13
VC1
Passive
Cable-side pair 1 center-tap / PoE common-mode terminal
14
VC2
Passive
Cable-side pair 2 center-tap / PoE common-mode terminal
15
VC3
Passive
Cable-side pair 3 center-tap / PoE common-mode terminal
16
VC4
Passive
Cable-side pair 4 center-tap / PoE common-mode terminal
17
~
Passive
LED 1 yellow cathode (−)
18
~
Passive
LED 1 yellow anode (+)
19
~
Passive
LED 2 orange anode (+) / green cathode (−)
20
~
Passive
LED 2 orange cathode (−) / green anode (+)
S1
SHIELD_S1
Passive
Metal shield / EMI chassis tab S1
S2
SHIELD_S2
Passive
Metal shield / EMI chassis tab S2

2250506-1