I started two separate projects and recorded the original unequal-size requirements.
FC project: latest saved state has 36 components and 27 nets, including STM32F405, ICM-42688-P gyro, 16MB flash, USB-C, USB protection, clock oscillator and 3.3V regulator parts. Electrical capture progressed, but I haven’t completed the final connectivity, power and firmware-compatibility review. The 39 × 39mm size is recorded—not yet implemented as a finished PCB layout.
ESC project:4 components and 3 nets form a provisional battery-voltage divider/filter and TVS branch. The unloaded divider was simulated; inspection found 0 ERC errors and 1 warning. This is not yet a working motor ESC.
Still unresolved: actual ESC bare-board geometry within the published 40.9 × 44.9mm heatsink-inclusive envelope, exact ten-pin cable mapping, and verified OX32 controller/firmware access. Motor power stages, matching pad positions/silkscreen, PCB routing and 55A load/thermal validation remain unfinished; neither board is manufacturing-ready or an exact verified copy.
Two physically separate projects with approved ORIGINAL UNEQUAL sizes: this project holds the 39x39mm FC; /setej72878/four-channel-55a-esc-prototype holds the ESC. Equal-board sizing is rejected. Reference FC height is 4.9mm; ESC 40.9x44.9x8mm envelope includes heatsink, not verified bare-board geometry. Original absolute pad coordinates and notch geometry remain unverified.
Uploaded source inspected
Uploaded five-page PDF.
Downloaded and inspected all five rendered pages. The PDF is image-only: text extraction returned no text. Pages show ESC component locations, FC top/bottom locations, FC–ESC wiring and stack orientations, motor/power wiring, and FC external-device wiring. It does not contain an internal schematic, BOM, Gerbers, dimensioned fabrication drawing or firmware source.
Visible interface information
Four motors; twelve motor-phase pads, battery positive/negative pads, TVS protection and external 1000uF capacitor.
Solder interconnect diagram identifies M4, M3, M2, M1, telemetry, current, GND and VBAT. Do not equate these eight functions with a verified ten-position connector pin order: duplicated contacts and numbering/orientation need separate confirmation.
Ten-position FC–ESC connector is shown. Original mating connector pitch and pin numbering must be sourced before placement/wiring.
FC shows USB Type-C, STM32 F405, gyro, Bluetooth chip/antenna, barometer, OSD, BOOT, LED indicators, GPS/compass connection, receiver connections and HD/analog VTX interfaces.
External pad labels include camera, buzzer, LED, UART, servo, power, RSSI and I2C functions. Exact coordinates are not dimensioned, so images alone do not establish exact manufacturing positions.
ESC illustration is inconsistent: page 1 title says BLS 55A, while page 4 heatsink text says 32-Bit. Do not infer the actual controller silicon or firmware from this mixed reference.
The ESC figures include its heatsink: bare PCB edge geometry is not established by these bounding dimensions. Equal mounting spacing does not mean equal board size.
Official electrical targets, not reproduced-design verification
The manufacturer's listing identifies STM32F405, ICM42688P, SPA06-003, AT7456E, 16MB blackbox, 3–6S input, 5V/9V BEC outputs and Betaflight SPEEDYBEEF405V5. ESC listing identifies OX32, DSHOT300/600, telemetry/current sense, 55A/channel continuous and 70A/channel peak. These describe the commercial reference; they do not validate this empty project's performance or firmware compatibility. Public manual search has a different barometer suffix; resolve against actual chosen component and firmware source before wiring.
Build status and gates
Project renamed F405 Flight Controller Prototype. Added STM32F405RGT6 U1, ICM-42688-P U2 and 16MB W25Q128JVSIM TR U3 as sourced primary candidates. No nets, support circuits, PCB geometry or routing created at this source checkpoint. Separate ESC project exists and is not mutated by this FC pass.
RESOLVED: user selected original unequal sizes; FC39x39mm. Bare ESC outline and FC notch geometry still need authoritative mechanical data.
Exact-copy claim requires original PCB/CAD/Gerber data and circuit/BOM evidence, unavailable in supplied manual. Otherwise build an explicitly new compatible prototype with matching verified interfaces, not a verified clone.
ESC silicon, gate drive, protection and firmware availability must be verified before designing a working power stage. OX32 and proprietary Bluetooth/app behavior cannot be promised from photographs.
55A continuous capability requires copper/busbar, MOSFET, cooling and assembled-board load/thermal validation; never label an untested design as verified 55A.
Next pass after mechanical choice: dimensioned two-board brief/specification; current project holds FC, separate project holds ESC; schematic capture and review before placement, then placement approval before routing.
Requested target
Uploaded source inspected
Visible interface information
Official reference dimensions
Official electrical targets, not reproduced-design verification