Carrier Board Design Inquiry
0:57
Planning battery replacement.
Thinking deeply about your request.
Considering project suggestions.
Defining project requirements.
Working on your request.
You want the carrier board updated to use a CR2350 battery holder instead of a CR2050 battery holder.
- I updated the plan to swap the battery requirement to CR2350
- The rest stays the same: DRV5032 on GPIO1.11, SWD test pads, and battery-net wiring
- Since this source project is read-only, run it in a new editable project
Click Start on the plan bar to proceed.
Plan
- Build a carrier board for the XIAO nRF54L module that integrates a DRV5032 digital hall sensor input on GPIO1.11, places a CR2450 battery holder on the board's bottom side, and includes SWD test pads (SWDCK and SWDIO). The design updates the battery specification from CR2050/CR2350 to CR2450 and is implemented in a new editable project.
#Implementation plan
- Create a new editable project based on the existing 'Seeed Studio XIAO nRF54L15 Sense' but update the design context to allow modifications.
- Add the core XIAO nRF54L module to the schematic and configure it for carrier-board use.
- Connect GPIO1.11 to the input of the DRV5032 digital hall sensor:
- Place the DRV5032 sensor symbol and route its digital output to the XIAO nRF54L's GPIO1.11 pin.
- Update the battery subsystem:
- Remove previous battery requirements and add a CR2450 battery holder to the schematic.
- Position the battery holder on the bottom side of the PCB.
- Wire the battery holder pads to the battery net.
- Add SWD test pads:
- Place separate test pads for SWDCK and SWDIO.
- Connect these pads to the corresponding SWD pins on the XIAO nRF54L module to ensure debugging accessibility.
- Review the placement and routing of all components ensuring minimal board size while maintaining functional integrity.
#Success criteria
- A new editable project is created reflecting the revised requirements.
- The schematic includes the XIAO nRF54L module with the DRV5032 sensor feeding into GPIO1.11, a CR2450 battery holder correctly wired to the battery net, and SWD test pads for both SWDCK and SWDIO.
- The PCB layout features a compact design with the battery holder placed on the bottom side, meeting updated battery requirements and overall system functionality.
7 days
0:52
Thinking deeply about your request.
Creating a project proposal.
Planning project steps.
Working on your request.
Creating a project plan.
Planning response content.
You want the carrier board updated to use a CR2450 battery holder instead of the earlier battery size.
- I updated the plan to use a bottom-side CR2450 battery holder
- The rest remains: XIAO nRF54L module, DRV5032 on GPIO1.11, and test pads for SWDCK/SWDIO
Click Start on the plan bar to proceed.
Plan
- Build a carrier board for the XIAO nRF54L module that integrates a DRV5032 digital hall sensor input on GPIO1.11, places a CR2450 battery holder on the board's bottom side, and includes SWD test pads (SWDCK and SWDIO). The design updates the battery specification from CR2050/CR2350 to CR2450 and is implemented in a new editable project.
#Implementation plan
- Create a new editable project based on the existing 'Seeed Studio XIAO nRF54L15 Sense' but update the design context to allow modifications.
- Add the core XIAO nRF54L module to the schematic and configure it for carrier-board use.
- Connect GPIO1.11 to the input of the DRV5032 digital hall sensor:
- Place the DRV5032 sensor symbol and route its digital output to the XIAO nRF54L's GPIO1.11 pin.
- Update the battery subsystem:
- Remove previous battery requirements and add a CR2450 battery holder to the schematic.
- Position the battery holder on the bottom side of the PCB.
- Wire the battery holder pads to the battery net.
- Add SWD test pads:
- Place separate test pads for SWDCK and SWDIO.
- Connect these pads to the corresponding SWD pins on the XIAO nRF54L module to ensure debugging accessibility.
- Review the placement and routing of all components ensuring minimal board size while maintaining functional integrity.
#Success criteria
- A new editable project is created reflecting the revised requirements.
- The schematic includes the XIAO nRF54L module with the DRV5032 sensor feeding into GPIO1.11, a CR2450 battery holder correctly wired to the battery net, and SWD test pads for both SWDCK and SWDIO.
- The PCB layout features a compact design with the battery holder placed on the bottom side, meeting updated battery requirements and overall system functionality.
Find CR2450 holders
Check holder footprint
Review voltage impact
7 days
To get started, talk to Flux or create a New Document.
Welcome 👋
Flux accelerates your PCB design with AI.
Create your account to start using this component and bring your ideas to life.