Welcome to your new project. Imagine what you can build here.

quiero que de las siguientes instrucciones lo plasmes en un protoboard: Transformador: Convierte la tensión de CA de la red eléctrica (120 V) en una tensión de CA de menor voltaje (por ejemplo, 12 V). Puente rectificador: Convierte la tensión de CA de bajo voltaje en una tensión de CC pulsante. Filtro: Compuesto por condensadores y resistencias, elimina la ondulación de la tensión de CC pulsante y produce una tensión de CC más estable. Circuito regulador: Mantiene la tensión de CC a un nivel constante, incluso si la tensión de entrada o la carga varían. Este circuito puede ser un circuito integrado (CI) regulador de voltaje o un circuito discreto con transistores. Carga: Dispositivo que consume la energía eléctrica proporcionada por la fuente de alimentación, como una bombilla, un motor o un circuito electrónico. Conexiones: La entrada de CA se conecta al transformador. La salida de CA del transformador se conecta al puente rectificador. La salida de CC del puente rectificador se conecta al filtro. La salida de CC del filtro se conecta al circuito regulador. La salida de CC del circuito regulador se conecta a la carga.

Welcome to your new project. Imagine what you can build here.

This project is a Switched-Mode Power Supply (SMPS) design. The design incorporates an AC DC Converter (NCP1203D100R2), polarized capacitors, resistors, diodes, connectors, a transistor, a transformer and an integrated circuit. #AC #DC #POWER #NCP1203 #project

A discrete 555 timer plug-in replacement composed of 26 transistors and 16 resistors. #N555 #transistor #resistor

This circuit drives 10 LEDs making them flash to the rhythm of the music (using a TIP31C transistor to act as a voltage-controlled switch) Credit: https://www.youtube.com/watch?v=3qZ3uA8hDmE

This project is a doorbell system reference design with an integrated camera. It leverages an ESP32 microcontroller for processing, along with various components including resistors, buzzers, and transistors. The system also features a charging circuitry with a USB-C connection for power supply. #referenceDesign #edge-computing #edgeComputing #SeeedStudio #template #iot #esp32#camera #reference-design

A transistor in which one p-type material is placed between two n-type materials.

This is a typical transistor key controlled by a button that turns on an LED. The project is with a schematic and 3D simulation

This is a typical transistor key controlled by a button that turns on an LED. The project is with a schematic and 3D simulation

Demo Transistor Switch Relay | Forked Design

Welcome to your new project. Imagine what you can build here.

Welcome to your new project. Imagine what you can build here.

The Ariel AI Chip, a state-of-the-art integrated circuit designed for high-performance computing applications, incorporates an innovative architecture that leverages radical transistor technology to optimize AI and machine learning tasks. At the heart of this chip lies a quad-core CPU operating at a clock speed of 2GHz, distinguished by its part number CPU-RT-4C-2G. The chip's power management is efficiently handled by a DC power supply, specified as DCPS-5V, ensuring a stable 5V input. Key to its operation are two NPN transistors, identified by part numbers NPN-TRANS-001 and NPN-TRANS-002, which, along with a pair of 1kΩ resistors (RES-1K and RES-1K-002) and a 10µF capacitor (CAP-10UF), form the critical signal processing and conditioning circuitry. This assembly is designed for seamless integration into advanced computing systems, particularly those focused on Flux AI environments, where its performance and efficiency can be fully leveraged. The Ariel AI Chip sets a new benchmark in AI computing, offering unparalleled processing power and efficiency for cutting-edge applications.

This project is a reference design utilizing Texas Instruments' PGA300ARHHR, a precision analog and digital IC, for signal processing. The circuit also includes a Diodes Incorporated's FZT603QTA Transistor, passive components like resistors and capacitors, and connectors from JST Sales America Inc. #project #referenceDesign #industrialsensing #texas-instruments #template #reference-design

The Ariel AI Chip, a pioneering component in the realm of artificial intelligence hardware, integrates a suite of electronic elements tailored for high-performance computing applications. At the heart of this assembly lies a CPU with a Radical Transistor architecture, featuring a quad-core setup clocked at 2GHz, identified by the part number CPU-RT-4C-2G. Power management is facilitated through a DC Power Supply, marked DCPS-5V, ensuring a stable 5V supply to the intricate circuitry. The chip's switching capabilities are bolstered by two NPN transistors, NPN-TRANS-001 and NPN-TRANS-002, which play a crucial role in signal modulation. Essential to the chip's operation are the passive components: two 1kΩ resistors (RES-1K and RES-1K-002) and a 10µF capacitor (CAP-10UF), which together with the transistors, form a robust network ensuring reliable performance under varying load conditions. Designed for integration into advanced AI systems, this chip stands out for its innovative use of standard components in a configuration that emphasizes efficiency, reliability, and high-speed data processing capabilities.

The Ariel AI chip prototype, designed for integration with Flux AI for advanced simulation and testing, incorporates a suite of electronic components optimized for high-performance computing applications. At the heart of this system lies a CPU with a radical transistor architecture, featuring a 4-core configuration and a clock speed of 2GHz, identified by part number CPU-RT-4C-2G. Power management is facilitated through a DC Power Supply, specified as DCPS-5V, ensuring a stable 5V supply to the system. The circuit's dynamic performance is modulated by two NPN transistors, NPN-TRANS-001 and NPN-TRANS-002, which, along with precision resistors RES-1K and RES-1K-002 (both 1kΩ), and a 10μF capacitor (CAP-10UF), form the critical signal processing path leading to the CPU. This configuration is designed to provide an efficient, reliable processing environment for AI computations, with an emphasis on minimizing latency and maximizing throughput. The Ariel AI chip's architecture, combining traditional components with an innovative CPU design, offers a versatile platform for developing advanced AI applications, reflecting a significant step forward in computational technology.

The Ariel AI Chip, a pioneering component in the field of artificial intelligence hardware, integrates advanced features designed to enhance computational efficiency and AI processing capabilities. This chip is distinguished by its utilization of a quad-core CPU with a clock speed of 2GHz, operating on a radical transistor architecture that promises significant improvements in speed and power efficiency. Key components that constitute the Ariel AI Chip include a DC power supply with a 5V output (DCPS-5V), NPN transistors (NPN-TRANS-001 and NPN-TRANS-002) that serve as the fundamental switching elements, precision resistors (RES-1K and RES-1K-002) each with a resistance of 1kΩ, and a capacitor (CAP-10UF) rated at 10μF to stabilize voltage and filter noise. This chip is designed for integration into systems requiring advanced AI capabilities, offering a comprehensive solution for developers looking to leverage machine learning and artificial intelligence in their applications. With its innovative architecture and component selection, the Ariel AI Chip stands out as a versatile and powerful tool for a wide range of AI applications, from embedded systems to more complex computational platforms.

This circuit drives 10 LEDs making them flash to the rhythm of the music (using a TIP31C transistor to act as a voltage-controlled switch) Credit: https://www.youtube.com/watch?v=3qZ3uA8hDmE

The Ariel AI Chip, an innovative component designed for high-performance computing applications, integrates a sophisticated array of electronic parts to deliver unparalleled processing capabilities. At the heart of this system is a CPU with a radical transistor architecture, featuring a core count of 4 and a clock speed of 2GHz, identified by its part number CPU-RT-4C-2G. Power management within the chip is efficiently handled by a DC Power Supply, rated at 5V, with the part number DCPS-5V, ensuring stable and reliable operation. The chip's signal processing and amplification needs are addressed through the inclusion of two NPN transistors, with part numbers NPN-TRANS-001 and a similar variant, providing the necessary gain and switching capabilities for complex computational tasks. Signal conditioning is further enhanced by a pair of 1kΩ resistors, RES-1K and RES-1K-002, and a 10µF capacitor, CAP-10UF, which work together to filter and stabilize the power supply and signal pathways, ensuring clean and noise-free operation. This integration of components within the Ariel AI Chip offers electrical engineers a robust platform for developing advanced AI systems, combining high processing power with efficient power management and signal integrity, suitable for a wide range of applications in the field of artificial intelligence.

This circuit drives 10 LEDs making them flash to the rhythm of the music (using a TIP31C transistor to act as a voltage-controlled switch) Credit: https://www.youtube.com/watch?v=3qZ3uA8hDmE

Nice — you can do a clean pulse + latch using a single quad Schmitt-NAND chip: 74HC132 (or 74LVC132 for 3.3 V systems). The HC132 contains four 2-input NAND gates with Schmitt inputs so you can both clean a noisy SYN480R DATA line and build an SR latch (NAND SR is active-LOW) inside one package. Only a few passives and a driver transistor are needed. Below is a ready-to-build recipe (parts, wiring, explanation, tuning tips, and an ASCII schematic) — no extra logic ICs required. Parts (per latch) 1 × 74HC132 (quad 2-input NAND with Schmitt inputs). If your system is 3.3 V use 74LVC132 / 74HC132 rated for 3.3 V. Rin = 47 kΩ (input series) Cfilter = 10 nF (input RC to ground) — tweak for debounce/clean time Rpulldown = 100 kΩ (pull-down at input node, optional) Rpullup = 100 kΩ (pull-up for active-LOW R input so reset is idle HIGH) Rbase = 10 kΩ, Q = 2N2222 (NPN) or small N-MOSFET (2N7002) to drive your load Diode for relay flyback (1N4001) if you drive a coil Optional small cap 0.1 µF decoupling at VCC of IC Concept / how it works (short) Use Gate1 (G1) of 74HC132 as a Schmitt inverter by tying its two inputs together and feeding a small RC filter from SYN480R.DATA. This removes HF noise and provides a clean logic transition. Because it's a NAND with tied inputs its function becomes an inverter with Schmitt behavior. Use G2 & G3 as the cross-coupled NAND pair forming an SR latch (active-LOW inputs S̄ and R̄). A low on S̄ sets Q = HIGH. A low on R̄ resets Q = LOW. Wire the cleaned/inverted output of G1 to S̄. A valid received pulse (DATA high) produces a clean LOW on S̄ (because G1 inverts), setting the latch reliably even if the pulse is brief. R̄ is your reset input (pushbutton, HT12D VT, MCU line, etc.) — idle pulled HIGH. Q drives an NPN/MOSFET to switch your load (relay, LED, etc.). Recommended wiring (pin mapping, assume one chip; use datasheet pin numbers) I’ll refer to the 4 gates as G1, G2, G3, G4. Use G4 optionally for additional conditioning or to build a toggler later. SYN480R.DATA --- Rin (47k) ---+--- Node A ---||--- Cfilter (10nF) --- GND | Rpulldown (100k) --- GND (optional, keeps node low) Node A -> both inputs of G1 (tie inputs A and B of Gate1 together) G1 output -> S̄ (S_bar) (input1 of Gate2) Gate2 (G2): inputs = S̄ and Q̄ -> output = Q Gate3 (G3): inputs = R̄ and Q -> output = Q̄ R̄ --- Rpullup (100k) --- VCC (reset is idle HIGH; pull low to reset) (optional) R̄ can be wired to a reset pushbutton to GND or to an MCU pin Q -> Rbase (10k) -> base of 2N2222 (emitter GND; collector to one side of relay coil) Other side of relay coil -> +V (appropriate coil voltage) Diode across coil If you prefer MOSFET low side switching: Q -> gate resistor 100Ω -> gate of 2N7002 2N7002 source -> GND ; drain -> relay coil low side

The Ariel AI chip prototype is an advanced electronic component designed for integration into the Flux AI environment, facilitating simulation and testing of AI applications. This component features a collection of carefully selected parts including a DC power supply (DCPS-5V), NPN transistors (NPN-TRANS-001 and NPN-TRANS-002), resistors (RES-1K and RES-1K-002), a capacitor (CAP-10UF), and a cutting-edge CPU (CPU-RT-4C-2G) with a 4-core architecture, operating at a clock speed of 2GHz. The CPU's innovative radical transistor architecture is specifically tailored for high-performance computing tasks associated with AI and machine learning applications. This configuration ensures efficient power management, signal processing, and data flow within the chip, making it an ideal choice for developers and engineers looking to push the boundaries of AI technology. The inclusion of standard components like NPN transistors, resistors, and capacitors, alongside the specialized CPU, allows for a versatile and robust design, suitable for a wide range of AI applications.

The NIKO-SEM PB600BA is an N-Channel Enhancement Mode Field Effect Transistor, presented in a compact PDFN 2x2S package. This semiconductor component operates with a maximum Drain-Source Voltage (VDS) of 30V and boasts a low On-Resistance (RDS(ON)) of 12mΩ, which enables efficient current handling of up to 9A at 25°C. The device is designed for high-performance applications, featuring a Gate-Source Voltage (VGS) range up to ±20V and capable of pulsed drain currents reaching 27A. Additionally, the PB600BA is Halogen-Free and Lead-Free, making it compliant with RoHS standards. It also supports an Avalanche Current (IAS) of 12.6A and an Avalanche Energy (EAS) of 7.9mJ. With thermal resistance parameters optimized for reliable operation, this transistor is ideal for power management and switching applications in various electronic designs.

The Ariel AI chip prototype is an advanced electronic component designed to enhance the capabilities of Flux AI systems through a sophisticated arrangement of transistors, resistors, capacitors, and a cutting-edge CPU. Key components include two NPN transistors (part numbers NPN-TRANS-001 and NPN-TRANS-002), which are essential for signal amplification, alongside precision resistors (RES-1K and RES-1K-002) each with a resistance of 1kΩ, and a capacitor (CAP-10UF) with a capacitance of 10μF, crucial for filtering and stabilizing the voltage supply. At the heart of the design is a revolutionary CPU (part number CPU-RT-4C-2G) featuring a quad-core setup with a clock speed of 2GHz, based on a radical transistor architecture, designed to deliver unparalleled computational performance for AI tasks. This component set is powered by a 5V DC power supply (DCPS-5V), ensuring a stable and efficient operation. The Ariel AI chip is engineered for high-speed, reliable performance in demanding AI applications, representing a significant advancement in electronic component design for artificial intelligence systems.

The 2N7002DW from iSion is a high-speed N-channel enhancement mode field-effect transistor (FET) designed for pulse amplifier and drive applications. Manufactured using the N-Channel DMOS process, this component offers robust performance with a maximum drain-source voltage (VDSS) of 60V and a gate-source voltage (VGSS) of +20V. It features a continuous drain current (ID) of 300mA and a pulsed drain current (IDM) of 800mA, making it suitable for demanding switching tasks. The 2N7002DW is compliant with ESD MIL-STD 833, providing +2.5KV contact discharge protection. Available in a compact SOT-363 package, the device also adheres to full RoHS standards, ensuring environmentally friendly compliance. Key electrical characteristics include a gate threshold voltage (VGS(th)) range of 1.0V to 2.5V, a static drain-source on-resistance (RDS(ON)) of up to 3.0Ω at VGS of 10V, and dynamic switching times with a turn-on delay (td(on)) of 6ns and a turn-off delay (td(off)) of 25ns. This transistor is ideal for engineers seeking reliable performance in high-speed pulse applications.

This circuit drives 10 LEDs making them flash to the rhythm of the music (using a TIP31C transistor to act as a voltage-controlled switch) Credit: https://www.youtube.com/watch?v=3qZ3uA8hDmE

This project is a H-Bridge Circuit used to control the rotation direction of a DC motor. It uses resistors, diodes, and transistors to alternately forward and reverse the current flow. #HBridge #project #Template #projectTemplate

This project is a plant care system that uses an ESP32-S3-MINI-1U-N8 microcontroller to automate plant care tasks. This system includes three Songle relays, multiple resistors, capacitors, and transistors, all powered at 3.3V, 5V, or 12V. It also incorporates a USB Type-C connector. #referenceDesign #edge-computing #edgeComputing #espressif #template #iot #ESP32 #relay #reference-design

Design a circuit that detects the presence of the infrared signal. The circuit should light a red LED when infrared signal is detected otherwise it should light a green LED. You may use NPN transistors, IR LED, Photodiode, Red LED, Green LED and a rectifier diode.

This project is a doorbell system reference design with an integrated camera. It leverages an ESP32 microcontroller for processing, along with various components including resistors, buzzers, and transistors. The system also features a charging circuitry with a USB-C connection for power supply. #referenceDesign #edge-computing #edgeComputing #SeeedStudio #template #iot #esp32#camera #reference-design

quiero que de las siguientes instrucciones lo plasmes en un protoboard: Transformador: Convierte la tensión de CA de la red eléctrica (120 V) en una tensión de CA de menor voltaje (por ejemplo, 12 V). Puente rectificador: Convierte la tensión de CA de bajo voltaje en una tensión de CC pulsante. Filtro: Compuesto por condensadores y resistencias, elimina la ondulación de la tensión de CC pulsante y produce una tensión de CC más estable. Circuito regulador: Mantiene la tensión de CC a un nivel constante, incluso si la tensión de entrada o la carga varían. Este circuito puede ser un circuito integrado (CI) regulador de voltaje o un circuito discreto con transistores. Carga: Dispositivo que consume la energía eléctrica proporcionada por la fuente de alimentación, como una bombilla, un motor o un circuito electrónico. Conexiones: La entrada de CA se conecta al transformador. La salida de CA del transformador se conecta al puente rectificador. La salida de CC del puente rectificador se conecta al filtro. La salida de CC del filtro se conecta al circuito regulador. La salida de CC del circuito regulador se conecta a la carga.

A simple pre-amplifier circuit based on two transistors

This project is a plant care system that uses an ESP32-S3-MINI-1U-N8 microcontroller to automate plant care tasks. This system includes three Songle relays, multiple resistors, capacitors, and transistors, all powered at 3.3V, 5V, or 12V. It also incorporates a USB Type-C connector. #referenceDesign #edge-computing #edgeComputing #espressif #template #iot #ESP32 #relay #reference-design

SOT-23-5 is a small 5-pin Surface Mount Device (SMD) package with a body size of 3mm x 1.4mm and a lead pitch of 0.95mm. The package has a low profile and is commonly used for small signal transistors and diodes. #part #template

Onboarding example document for new users.

A transistor in which one p-type material is placed between two n-type materials.

A transistor in which one p-type material is placed between two n-type materials.

A transistor in which one p-type material is placed between two n-type materials.

A transistor in which one p-type material is placed between two n-type materials.

Humidity Contoller using 2n2222 transistor

This is a typical transistor key controlled by a button that turns on an LED. The project is with a schematic and 3D simulation

A transistor in which one p-type material is placed between two n-type materials.

Transistor based tremolo circuit using the LFO from the Vox AC15C1. Based on an idea by Leyland Pedals. https://www.reddit.com/r/diypedals/comments/kgs9ki/ultra_simple_tremolo_schematic_and_video/

Welcome to your new project. Imagine what you can build here.