LED Driver IC 1 Output DC DC Controller SEPIC, Step-Down (Buck), Step-Up (Boost) Analog, PWM Dimming 8-SO-EP # AL8866QSP-13 Engineering Specifications **General Description** The AL8866QSP-13 is an automotive-qualified, multi-topology DC-switching LED controller manufactured by Diodes Incorporated. It is designed to control an external power MOSFET for high-power automotive LED lighting systems. The device supports buck, boost, buck-boost and single-ended primary-inductance converter configurations. Its wide input-voltage range makes it suitable for automotive power systems and various high-voltage LED applications. The controller uses fixed-frequency peak current-mode regulation with spread-spectrum frequency modulation to reduce electromagnetic interference. It supports both analog and pulse-width-modulation dimming through the DIM input. An integrated programmable soft-start function gradually increases the inductor and switching currents during startup to reduce output-voltage and current stress. The open-drain fault output provides system-level fault reporting for abnormal operating conditions. **Engineering Specifications** **Manufacturer:** Diodes Incorporated **Manufacturer Part Number:** AL8866QSP-13 **Component Type:** Automotive LED driver controller **Converter Topologies:** Buck, boost, buck-boost and SEPIC **Control Architecture:** Fixed-frequency peak current-mode control **External Switching Device:** External power MOSFET **Minimum Input Voltage:** Four point seven volts **Maximum Input Voltage:** Eighty-five volts **Maximum Output Voltage:** Eighty-five volts **Switching Frequency:** Four hundred kilohertz **Frequency Modulation:** Spread-spectrum modulation for reduced electromagnetic interference **LED Current Control:** External current-sense resistor and external MOSFET configuration **Feedback Voltage:** Two hundred millivolts **Typical Quiescent Current:** One point eight milliamperes **Typical Efficiency:** Up to approximately ninety-three percent, depending on the application circuit and external components **Dimming Methods:** Analog dimming and pulse-width-modulation dimming **Analog Dimming Range:** One percent to one hundred percent **Analog Dimming Dynamic Range:** Greater than one hundred to one **Pulse-Width-Modulation Dimming Ratio:** One hundred to one at a two-hundred-hertz dimming frequency **Pulse-Width-Modulation Frequency Range:** Approximately one hundred hertz to one kilohertz **Full-Brightness Current Accuracy:** Approximately plus or minus three percent **Low-Level Dimming Current Accuracy:** Approximately plus or minus twelve percent at twenty-percent dimming **Soft-Start Function:** Externally programmable **Fault Output:** Active-low open-drain fault indicator **Protection Features:** Output overvoltage protection, LED open-circuit protection, output undervoltage protection, LED short-circuit protection, cycle-by-cycle overcurrent limitation, current-sense resistor short-circuit protection, inductor and diode short-circuit detection, diode open-circuit protection and thermal shutdown **Automotive Qualification:** AEC-Q100 Grade One qualified **Automotive Documentation:** PPAP capable **Manufacturing Standard:** Manufactured in IATF-certified automotive facilities **Operating Temperature Range:** Minus forty degrees Celsius to positive one hundred twenty-five degrees Celsius **Package Type:** Thermally enhanced SO-8 exposed-pad package **Pin Count:** Eight leads with exposed thermal ground pad **Mounting Style:** Surface mount **Packing Method:** Thirteen-inch tape and reel **Standard Packing Quantity:** Two thousand five hundred components per reel **Moisture Sensitivity:** Level One **Terminal Finish:** Matte-tin-plated leads **Environmental Compliance:** Lead-free, RoHS compliant, halogen-free and antimony-free **Typical Applications** Automotive high-beam and low-beam lighting Automotive daytime running lights Automotive fog lights Automotive turn-signal lights Automotive position lights Automotive brake and stop lights High-power exterior LED lighting Multi-topology automotive LED driver modules #AL8866QSP13 #AL8866Q #DiodesIncorporated #LEDDriver #AutomotiveLED #AutomotiveElectronics #BuckConverter #BoostConverter #BuckBoostConverter #SEPICConverter #PowerElectronics #LEDLighting #ElectronicComponents #EngineeringSpecifications

0.5 mOhms ±1% 5W Chip Resistor Nonstandard Automotive AEC-Q200, Current Sense Metal Element # Engineering Specification ## Product Name CSS4J-4026R-L500F ## General Description CSS4J-4026R-L500F is a precision four-terminal Kelvin current sense shunt resistor designed for accurate current measurement in high-performance electronic and power management systems. The device is intended for use in applications requiring low resistance sensing, high measurement accuracy, and stable thermal performance under varying electrical loads. The component utilizes a metal element resistive structure optimized for minimal resistance drift, reduced temperature effects, and consistent long-term stability. Its four-terminal Kelvin configuration separates current flow and voltage sensing paths, enabling improved measurement accuracy by eliminating errors caused by PCB trace and connection resistance. The device is widely used in power conversion systems, battery monitoring systems, motor control circuits, and industrial power electronics where precise current feedback is essential for control, protection, and monitoring functions. Its surface-mount construction supports compact PCB layouts and automated assembly processes while maintaining robust mechanical and electrical reliability. The design emphasizes efficient heat dissipation, stable electrical characteristics, and compatibility with demanding industrial and automotive environments. It is suitable for integration into systems requiring continuous current monitoring and high measurement fidelity. ## Functional Requirements ### Current Measurement The device shall provide accurate current sensing through a low-resistance conductive path designed for minimal measurement error. ### Kelvin Sensing Operation The device shall support four-terminal Kelvin sensing to improve measurement accuracy by separating current and voltage sensing paths. ### Signal Stability The device shall maintain stable sensing characteristics under varying load and thermal conditions. ### System Integration The component shall support integration into power electronics and embedded control systems requiring precise current feedback. ## Electrical Requirements ### Low Resistance Operation The device shall exhibit very low resistance to minimize power loss and maintain measurement accuracy. ### Thermal Stability The resistor shall maintain consistent electrical behavior under elevated operating temperatures and thermal cycling conditions. ### Power Handling The device shall support operation in high-current environments typical of power conversion and motor control systems. ### Measurement Accuracy The design shall support precise voltage drop measurement proportional to current flow for control and monitoring applications. ## Mechanical Requirements ### Surface Mount Construction The device shall be provided in a surface mount package suitable for automated PCB assembly. ### Structural Integrity The component shall maintain mechanical stability during assembly, operation, and thermal cycling. ### PCB Integration The device shall support direct integration into multilayer printed circuit board designs with optimized current path layout. ## Environmental Requirements ### Operating Conditions The device shall operate reliably under industrial and automotive environmental conditions. ### Thermal Performance The component shall maintain performance stability under continuous electrical loading and heat generation. ### Storage and Handling The device shall maintain physical and electrical integrity during storage, transport, and handling procedures. ## Quality Requirements ### Reliability The device shall provide long-term stability in resistance value and sensing accuracy under continuous operation. ### Verification Electrical, thermal, and mechanical characteristics shall be validated through appropriate testing and qualification procedures. ### Compliance The product shall conform to applicable standards for current sensing resistors used in industrial and automotive electronics. ## Documentation Requirements Technical documentation shall include application guidelines, layout recommendations for Kelvin sensing, thermal considerations, electrical characteristics, and integration practices for power electronics systems. ## Classification Tags #CSS4J4026RL500F #CurrentSenseResistor #ShuntResistor #KelvinSensing #FourTerminalResistor #PowerElectronics #BatteryManagement #MotorControl #PowerSupplyDesign #AnalogSensing #ElectricalEngineering #PCBDesign #EmbeddedSystems #IndustrialElectronics #AutomotiveElectronics #CommonPartsLibrary #ComponentLibrary #EngineeringSpecification #TechnicalDocumentation #HighCurrentSensing #PrecisionMeasurement #CircuitDesign

Current Sense Amplifier 1 Circuit Single-Ended SOT-23-6 The INA187A3IDBVR is a precision high-side and low-side current sense amplifier designed for accurate bidirectional current measurement in power management, motor control, battery monitoring, and industrial sensing applications. The device integrates a matched precision gain stage optimized for shunt resistor voltage amplification while maintaining excellent common-mode rejection and low offset drift. It supports wide common-mode input voltages, enabling current monitoring across supply rails in automotive, industrial, and embedded systems. The amplifier features fast response characteristics, low quiescent current consumption, and a compact surface-mount package suitable for space-constrained designs. Engineering Specification Device Type Precision Current Sense Amplifier Manufacturer Texas Instruments Manufacturer Part Number INA187A3IDBVR Amplifier Configuration Current shunt monitor with fixed gain Gain Variant High fixed gain configuration optimized for low-value shunt resistor sensing Input Measurement Capability Bidirectional current sensing Common-Mode Voltage Range Supports high-side and low-side sensing across wide supply rails Input Offset Characteristics Low offset voltage with low temperature drift for accurate current measurement Bandwidth Performance Wide bandwidth suitable for dynamic load and transient current monitoring Response Time Fast settling and propagation performance for real-time current feedback systems Power Supply Requirements Single-supply operation compatible with low-voltage logic systems Output Type Analog voltage output proportional to sensed shunt voltage Common-Mode Rejection High common-mode rejection ratio for stable operation in noisy environments Temperature Performance Industrial operating temperature range with stable gain accuracy over temperature Protection Features Robust input structure designed for high common-mode environments Package Type SOT-23 surface-mount package Mounting Method Surface mount technology Typical Applications Battery management systems, power distribution monitoring, motor current feedback, DC/DC converter monitoring, industrial automation, telecom power systems, and embedded power diagnostics. #commonpartslibrary #integratedcircuit #currentsenseamplifier