Use this template if you're planning to get your 1 to 2-layer board manufactured in JLCPCB. It has the via min/max and trace width constraints already baked as global rules. #project-template

Bitcoin miner controller board revised so J2 is a dedicated USB-C USB 2.0 control and monitoring connector feeding U2, while X1 is a dedicated 25 MHz oscillator driving IC1 on ASIC_CLK for the mining subsystem.

60 V automotive-style 24 V / 5 A DC-DC converter with cleaned J2 input path: J2 raw input through F1 fuse, SMAJ58A TVS, Q4 reverse-polarity MOSFET, then VIN_60V_PROTECTED handoff into the converter and LT4363 hot-swap stage.

Resonate Pendant golden reference design. Board is a 39 mm x 63 mm portrait rectangle with 5 mm corner radii, 2-layer FR4, 0.8 mm thickness, 1 oz copper on both layers, matte black top solder mask, no bottom solder mask, ENEPIG finish, and no silkscreen on either side. Allowed components only: U1 STM32L052C8T6, U2 CH340E, U3 BQ24210DQCT, C1 10uF, C2 4.7uF, C3-C7 100nF, R1 24k, R2 1k, R3 10k, D1 green 0402 LED, MAG1-MAG4 magnetic pads, J1 solar solder pads, J2 battery solder pads, TP1-TP4 test pads. Required top artwork: golden-ratio grid lines and gold circles on F.Cu with mask openings, decorative only, 0.8-1.0 mm width, at least 0.5 mm from active traces. Required bottom artwork: exposed ENEPIG bottom copper split into FREQ_OUT 61.8 percent and GND 38.2 percent with an exact 0.20 mm S-curve isolation gap, no vias through bottom except one PA4-to-FREQ_OUT via at the extreme edge. Functional requirements: MAG1 and J1 VIN feed U3 IN, U3 OUT feeds J2 battery pad and system VBAT, MAG2 to U2 UD+, MAG3 to U2 UD-, MAG4 to common ground, U2 TX to U1 PA10, U2 RX to U1 PA9, U1 PA4 to bottom FREQ_OUT, U1 PA5 to R2 then D1 to GND, U3 ISET to R1 to GND, U3 TS to R3 to GND, decoupling exactly as specified. Prohibited items: external crystal, JST connectors, wireless module, antenna, separate regulator IC, ESD protection IC, USB-C connector, through-hole parts, bottom solder mask, silkscreen, more than three ICs, or any unapproved substitutions.

SmartDeskPet v1.0 Shield Stage 1 status: - Goal: 5V input -> dual AMS1117-3.3 rails (+3V3_MCU and +3V3_WIFI) with common GND. - Note: Keep power nets explicitly named (avoid unnamed nets) to keep ERC happy. Stage 1 completion checklist: - Mark J1 Pin_1 (+5V) as a Power Output pin to satisfy ERC power-driver checks. - Verify all GND symbols/returns are on the same GND net. - Keep +5V_SERVO isolated from the main +5V net (only share GND). Stage 2 preparation notes (MPN/LCSC + layout constraints): - MPN/LCSC targets to define before Stage 2 exit: - AMS1117-3.3 (SOT-223): set exact MPN and (optionally) LCSC PN for both U1 and U2. - 100nF capacitor (0603): set MPN/LCSC for all 0603 100nF decouplers. - 4.7k resistor (0603): set MPN/LCSC for I2C pull-ups R1 and R2. - 1000uF bulk capacitor (radial): set MPN/LCSC for C7 (CP_Radial_D10.0mm_P5.00mm). - DC005 power jack/regulator input: select exact DC005 footprint + MPN/LCSC (if used). - 2.54mm headers/sockets: set MPN/LCSC for H1, H2, J1, J3, J4, J5, P3, P4, P5, and J2. - ESP-01S antenna keepout: - Reserve a copper keepout under and in front of the ESP-01S onboard antenna. - No copper pours/traces/components in the antenna region (top and bottom) per module guidelines. - H1/H2 header spacing: - Maintain 1000 mil spacing between H1 and H2 header centerlines (shield mechanical requirement). - Silkscreen placeholders: - Add silkscreen labels for: 5V IN, GND, +3V3_MCU, +3V3_WIFI, SERVO1, SERVO2, I2C SDA/SCL, DHT11, ASRPRO UART2, ESP-01S UART3. - Add placeholder text for: MPN, LCSC, board revision, and date code. Stage 3 layout constraints (placement and routing guidance): - Connector placement strategy: - Place H1 and H2 first to lock the shield mechanical interface; enforce 1000 mil spacing. - Place J1 and any DC005 input at the board edge for easy access. - Designated power area planning: - Group U1, U2, and C7 near the 5V entry point; keep high-current 5V and regulator loops short. - Use wide copper for +5V and any servo supply; stitch GND around power section. - Antenna keepout boundaries: - Place J2 (ESP-01S socket) at a board edge with the antenna facing outward. - Enforce a top-and-bottom copper keepout in the antenna region; keep noisy power traces away.

This is a template for your own Blue Pill shield with pinout on a board! #ARM #STM32 #IoT #Arduino #template

This is a template for your own Blue Pill shield with pinout on a board! #ARM #STM32 #IoT #Arduino #template

Phoenix Contact PS QUINT-PS/3AC/24DC/40

This is a template for your own Blue Pill shield with pinout on a board! #ARM #STM32 #IoT #Arduino #template