Learn how to use Copilot, your AI design assistant, to brainstorm and develop a new idea from concept to custom board design. Discuss requirements, generate architectures, research parts, and draw your schematic.

This design is three parts, one a bandpass filter to allow only a certain frequency to come through the device, and the other two to filter and jam out different frequencies that would be coming near the device. The bandpass is set at 450MHz as is the common frequency for phones, the top jammer is set up for blocking out typical radio frequencies while the bottom is set to block frequencies above that of a phone signal. Vin=20 volts

Learn how to design PCBs faster with generative AI in this 20 minute hands-on tutorial. You’ll learn how to use Flux Copilot, an AI-powered hardware design assistant, to research parts, review your design, and even connect components. https://youtu.be/FL7e0OXTLic

This project involves designing a PCB for the lid assembly of an open-source laptop. The design integrates various sensors, including a microphone, camera, and ambient light sensor, ensuring precise alignment with the display glass. It features touch sensors to control LED lighting, spring-loaded contacts for touch-key interaction, and 3D-printed light diffusers for efficient lighting. Additionally, the PCB includes a power management system with status LEDs and a PFC for connecting to the external laptop PCB. The goal is to create a versatile, upgradeable, and user-friendly component for the laptop's lid. Specific parts of the project include 1. Microphone - Audio input capture 2. Ambient Light Sensor Module - Light intensity measurement 3. Camera - Video capture 4. LDO Regulators (3 TLV74 Series) - Voltage regulation for different components 5. Crystal - Clock generation 6. Touch Sensor Controller - Touch-key interaction 7. Flip-Flop - State keeping in logic circuits 8. LEDs (LTRBR37G Series) - Lighting indication 9. FPC Connector - Interface with main laptop PCB

A simple voltage divider to showcase how to make parts. A voltage divider is a simple circuit which turns a large voltage into a smaller one. Using just two series resistors and an input voltage, we can create an output voltage that is a fraction of the input. Voltage dividers are one of the most fundamental circuits in electronics.

Learn how to design PCBs faster with generative AI in this 20 minute hands-on tutorial. You’ll learn how to use Flux Copilot, an AI-powered hardware design assistant, to research parts, review your design, and even connect components. https://youtu.be/FL7e0OXTLic

Learn how to design PCBs faster with generative AI in this 20 minute hands-on tutorial. You’ll learn how to use Flux Copilot, an AI-powered hardware design assistant, to research parts, review your design, and even connect components. https://youtu.be/FL7e0OXTLic

The Ariel AI Chip, an innovative component designed for high-performance computing applications, integrates a sophisticated array of electronic parts to deliver unparalleled processing capabilities. At the heart of this system is a CPU with a radical transistor architecture, featuring a core count of 4 and a clock speed of 2GHz, identified by its part number CPU-RT-4C-2G. Power management within the chip is efficiently handled by a DC Power Supply, rated at 5V, with the part number DCPS-5V, ensuring stable and reliable operation. The chip's signal processing and amplification needs are addressed through the inclusion of two NPN transistors, with part numbers NPN-TRANS-001 and a similar variant, providing the necessary gain and switching capabilities for complex computational tasks. Signal conditioning is further enhanced by a pair of 1kΩ resistors, RES-1K and RES-1K-002, and a 10µF capacitor, CAP-10UF, which work together to filter and stabilize the power supply and signal pathways, ensuring clean and noise-free operation. This integration of components within the Ariel AI Chip offers electrical engineers a robust platform for developing advanced AI systems, combining high processing power with efficient power management and signal integrity, suitable for a wide range of applications in the field of artificial intelligence.

Learn how to use Copilot, your AI design assistant, to brainstorm and develop a new idea from concept to custom board design. Discuss requirements, generate architectures, research parts, and draw your schematic.

Nice — you can do a clean pulse + latch using a single quad Schmitt-NAND chip: 74HC132 (or 74LVC132 for 3.3 V systems). The HC132 contains four 2-input NAND gates with Schmitt inputs so you can both clean a noisy SYN480R DATA line and build an SR latch (NAND SR is active-LOW) inside one package. Only a few passives and a driver transistor are needed. Below is a ready-to-build recipe (parts, wiring, explanation, tuning tips, and an ASCII schematic) — no extra logic ICs required. Parts (per latch) 1 × 74HC132 (quad 2-input NAND with Schmitt inputs). If your system is 3.3 V use 74LVC132 / 74HC132 rated for 3.3 V. Rin = 47 kΩ (input series) Cfilter = 10 nF (input RC to ground) — tweak for debounce/clean time Rpulldown = 100 kΩ (pull-down at input node, optional) Rpullup = 100 kΩ (pull-up for active-LOW R input so reset is idle HIGH) Rbase = 10 kΩ, Q = 2N2222 (NPN) or small N-MOSFET (2N7002) to drive your load Diode for relay flyback (1N4001) if you drive a coil Optional small cap 0.1 µF decoupling at VCC of IC Concept / how it works (short) Use Gate1 (G1) of 74HC132 as a Schmitt inverter by tying its two inputs together and feeding a small RC filter from SYN480R.DATA. This removes HF noise and provides a clean logic transition. Because it's a NAND with tied inputs its function becomes an inverter with Schmitt behavior. Use G2 & G3 as the cross-coupled NAND pair forming an SR latch (active-LOW inputs S̄ and R̄). A low on S̄ sets Q = HIGH. A low on R̄ resets Q = LOW. Wire the cleaned/inverted output of G1 to S̄. A valid received pulse (DATA high) produces a clean LOW on S̄ (because G1 inverts), setting the latch reliably even if the pulse is brief. R̄ is your reset input (pushbutton, HT12D VT, MCU line, etc.) — idle pulled HIGH. Q drives an NPN/MOSFET to switch your load (relay, LED, etc.). Recommended wiring (pin mapping, assume one chip; use datasheet pin numbers) I’ll refer to the 4 gates as G1, G2, G3, G4. Use G4 optionally for additional conditioning or to build a toggler later. SYN480R.DATA --- Rin (47k) ---+--- Node A ---||--- Cfilter (10nF) --- GND | Rpulldown (100k) --- GND (optional, keeps node low) Node A -> both inputs of G1 (tie inputs A and B of Gate1 together) G1 output -> S̄ (S_bar) (input1 of Gate2) Gate2 (G2): inputs = S̄ and Q̄ -> output = Q Gate3 (G3): inputs = R̄ and Q -> output = Q̄ R̄ --- Rpullup (100k) --- VCC (reset is idle HIGH; pull low to reset) (optional) R̄ can be wired to a reset pushbutton to GND or to an MCU pin Q -> Rbase (10k) -> base of 2N2222 (emitter GND; collector to one side of relay coil) Other side of relay coil -> +V (appropriate coil voltage) Diode across coil If you prefer MOSFET low side switching: Q -> gate resistor 100Ω -> gate of 2N7002 2N7002 source -> GND ; drain -> relay coil low side

make this for me now # Device Summary & Specification Sheet ## 1. Overview A rugged, Arduino-Uno-and-Raspberry-Pi-style single-board micro-PC featuring: - Smartphone-class CPU (Snapdragon 990) - USB-C Power Delivery + 4×AA alkaline backup + ambient-light harvester - On-board Arduino-Uno-compatible ATmega328P - External NVMe SSD via USB3 bridge & optional Thunderbolt 3 eGPU support - 5× USB 3.0 ports, HDMI in/out, Gigabit Ethernet & SFP fiber, Wi-Fi, Bluetooth, LoRa - 0.96″ OLED status display, 3.5 mm audio jack with codec --- ## 2. Key Specifications | Category | Specification | |--------------------|-------------------------------------------------------------------------------| | CPU | Snapdragon 990, octa-core up to 2.84 GHz | | Memory | 6 GB LPDDR4x DRAM | | Storage Interface | PCIe Gen3 ×4 → M.2 NVMe + USB 3.1 Gen1 bridge | | MCU | ATmega328P (Arduino-Uno-compatible) | | Power Input | USB-C PD up to 20 V/5 A; 4×AA alkaline backup; ambient-light photodiode boost | | Power Rails | 12 V, 5 V, 3.3 V, 1.8 V, 1.2 V via buck/buck-boost regulators | | USB Hub | 5× USB 3.0 downstream ports | | Display | 0.96″ 128×64 OLED via I²C/SPI | | Networking | 1 × Gigabit RJ45; 1 × SFP fiber; Wi-Fi 802.11ac + Bluetooth; LoRa SX1276 | | Video I/O | HDMI 2.0 input (RX) & output (TX) | | Audio | 3.5 mm jack + TLV320AIC3101 codec; Bluetooth audio | | Form Factor | Raspberry Pi–style header + Arduino-Uno shield headers; 4× standoff mounts | --- ## 3. Complete Parts List | Part | Function | Qty | |------------------------------------------------------------------------------------------------|-----------------------------------------------|-----| | [Snapdragon 990](https://www.flux.ai/search?type=components&q=Snapdragon%20990) | Main application CPU | 1 | | [LPDDR4x DRAM](https://www.flux.ai/search?type=components&q=LPDDR4x%20DRAM) | System memory | 1 | | [eMMC 64GB](https://www.flux.ai/search?type=components&q=eMMC%2064GB) | On-board storage | 1 | | [M.2 NVMe Connector](https://www.flux.ai/search?type=components&q=M.2%20NVMe%20Connector) | External SSD interface | 1 | | [JMS583](https://www.flux.ai/search?type=components&q=JMS583) | PCIe→USB 3.1 bridge for NVMe | 1 | | [Titan Ridge](https://www.flux.ai/search?type=components&q=Titan%20Ridge) | Thunderbolt 3/eGPU controller | 1 | | [STUSB4500](https://www.flux.ai/search?type=components&q=STUSB4500) | USB-C Power-Delivery controller | 1 | | [LTC4412](https://www.flux.ai/search?type=components&q=LTC4412) | Ideal-diode OR-ing | 1 | | [LTC3108](https://www.flux.ai/search?type=components&q=LTC3108) | Ambient-light (solar) energy harvester | 1 | | [Battery Holder 4×AA](https://www.flux.ai/search?type=components&q=Battery%20Holder%204xAA) | Alkaline backup power | 1 | | [TPS53318](https://www.flux.ai/search?type=components&q=TPS53318) | 6 V→5 V synchronous buck regulator | 1 | | [MCP1700-3302E/TO](https://www.flux.ai/search?type=components&q=MCP1700-3302E/TO) | 6 V→3.3 V LDO | 1 | | [TPS63060](https://www.flux.ai/search?type=components&q=TPS63060) | Buck-boost for 12 V rail (eGPU power) | 1 | | [ATmega328P](https://www.flux.ai/search?type=components&q=ATmega328P) | Arduino-Uno microcontroller | 1 | | [ESP32-WROOM-32](https://www.flux.ai/search?type=components&q=ESP32-WROOM-32) | Wi-Fi + Bluetooth co-processor | 1 | | [SX1276](https://www.flux.ai/search?type=components&q=SX1276) | LoRa transceiver | 1 | | [TUSB8041](https://www.flux.ai/search?type=components&q=TUSB8041) | 5-port USB 3.0 hub IC | 1 | | [Ethernet PHY](https://www.flux.ai/search?type=components&q=Ethernet%20PHY) | Gigabit Ethernet physical transceiver | 1 | | [SFP Cage](https://www.flux.ai/search?type=components&q=SFP%20Cage) | Fiber-optic SFP module connector | 1 | | [TDA19978](https://www.flux.ai/search?type=components&q=TDA19978) | HDMI 2.0 receiver (input) | 1 | | [TFP410](https://www.flux.ai/search?type=components&q=TFP410) | HDMI 2.0 transmitter (output) | 1 | | [TLV320AIC3101](https://www.flux.ai/search?type=components&q=TLV320AIC3101) | Audio codec for 3.5 mm jack & Bluetooth audio | 1 | | [Audio Jack 3.5mm](https://www.flux.ai/search?type=components&q=Audio%20Jack%203.5mm) | Headphone/mic port | 1 | | [SSD1306 OLED](https://www.flux.ai/search?type=components&q=SSD1306%20OLED) | Status display | 1 | --- ## 4. High-Level Design & Implementation Steps 1. **Schematic Creation** - Section off blocks: CPU + memory, power-supply, NVMe/USB bridge, MCU, wireless, USB hub, video, audio, I/O headers. - Place all parts from the list and wire per respective datasheet reference circuits. 2. **Power System** - Implement USB-C PD with STUSB4500 → buck/buck-boost & LDO rails. - Add LTC4412 to OR-ing battery pack into 6 V bus. - Include LTC3108 harvest input to 6 V bus (no recharge to AA). - Add decoupling & bulk caps per regulator datasheets; PTC fuses & ESD diodes on inputs. 3. **SoC & High-Speed Interfaces** - Break out Snapdragon 990 BGA with DDR4 routing (point-to-point). - Route PCIe Gen3 lanes to M.2 slot via JMS583 and to Titan Ridge for TB/eGPU. - Follow high-speed layout guidelines: impedance, length matching, EMI filters. 4. **MCU & Expansion Headers** - Place ATmega328P with UNO-style 2.54 mm headers; add ISP 6-pin, I²C pull-ups, reset circuit. 5. **Connectivity Blocks** - USB hub: TUSB8041 + ESD + chokes → five USB-A 3.0 ports. - Ethernet: RJ45 + magnetics + PHY; SFP cage + PHY/SFP interface. - Wireless: ESP32 module pad + SX1276 + antenna matching; program pads. 6. **Video & Audio** - HDMI RX (TDA19978) & TX (TFP410) blocks with TMDS ESD & termination. - Audio codec + 3.5 mm jack; route differential audio lines; add ESD. 7. **Display & Indicators** - SSD1306 OLED on I²C; add pull-ups & backlight power if needed. - LEDs for power, charge, status. 8. **PCB Layout & Mechanical** - Follow Raspberry Pi 2×20 header footprint & UNO shield hole pattern. - Add reinforcement for rugged use; standoffs at corners. - Define 4-layer stackup: • Top: signal • L2: GND • L3: PWR • Bottom: signal 9. **DRC/ERC Reviews** - Run ERC for decoupling, pull-ups, power nets. - Run DRC for high-speed clearance, differential pairs, via aspect ratios. 10. **Fabrication & Testing** - Export Gerbers, IPC-2581, BOM. - Prototype assembly; verify power sequencing, rails, interfaces. - Functional tests: USB-C PD negotiation, NVMe throughput, eGPU over TB3, wireless comm, audio, OLED. --- This spec sheet and part list should guide your Flux schematic and PCB layout workflow through to fabrication and validation. Let me know if you’d like to deep-dive into any specific block or review datasheet details next!

Learn how to use Copilot, your AI design assistant, to brainstorm and develop a new idea from concept to custom board design. Discuss requirements, generate architectures, research parts, and draw your schematic.

Learn how to use Copilot, your AI design assistant, to brainstorm and develop a new idea from concept to custom board design. Discuss requirements, generate architectures, research parts, and draw your schematic.

A simple voltage divider to showcase how to make parts. A voltage divider is a simple circuit which turns a large voltage into a smaller one. Using just two series resistors and an input voltage, we can create an output voltage that is a fraction of the input. Voltage dividers are one of the most fundamental circuits in electronics.

Learn how to design PCBs faster with generative AI in this 20 minute hands-on tutorial. You’ll learn how to use Flux Copilot, an AI-powered hardware design assistant, to research parts, review your design, and even connect components. https://youtu.be/FL7e0OXTLic

Learn how to design PCBs faster with generative AI in this 20 minute hands-on tutorial. You’ll learn how to use Flux Copilot, an AI-powered hardware design assistant, to research parts, review your design, and even connect components. https://youtu.be/FL7e0OXTLic

The Ariel AI chip prototype is an advanced electronic component designed for integration into the Flux AI environment, facilitating simulation and testing of AI applications. This component features a collection of carefully selected parts including a DC power supply (DCPS-5V), NPN transistors (NPN-TRANS-001 and NPN-TRANS-002), resistors (RES-1K and RES-1K-002), a capacitor (CAP-10UF), and a cutting-edge CPU (CPU-RT-4C-2G) with a 4-core architecture, operating at a clock speed of 2GHz. The CPU's innovative radical transistor architecture is specifically tailored for high-performance computing tasks associated with AI and machine learning applications. This configuration ensures efficient power management, signal processing, and data flow within the chip, making it an ideal choice for developers and engineers looking to push the boundaries of AI technology. The inclusion of standard components like NPN transistors, resistors, and capacitors, alongside the specialized CPU, allows for a versatile and robust design, suitable for a wide range of AI applications.

Welcome to your new project. Imagine what you can build here.

Welcome to your new project. Imagine what you can build here.

Welcome to your new project. Imagine what you can build here.

Welcome to your new project. Imagine what you can build here.

Sensor using through hole LDR and power with SMT LED Resistors and PZT3904

Welcome to your new project. Imagine what you can build here.

Welcome to your new project. Imagine what you can build here.

Welcome to your new project. Imagine what you can build here.

Welcome to your new project. Imagine what you can build here.

Welcome to your new project. Imagine what you can build here.

Welcome to your new project. Imagine what you can build here.

Sensor using through hole LDR and power with SMT LED Resistors and PZT3904

ddd

Welcome to your new project. Imagine what you can build here.

Learn how to use Copilot, your AI design assistant, to brainstorm and develop a new idea from concept to custom board design. Discuss requirements, generate architectures, research parts, and draw your schematic.

Firefly Board is part of a smart network designed for wireless control of light, water and other parts of the house in locations where GSM communication and WiFi are not available. #LoRa #smart #IoT #power #led #arm #stm32

Learn how to use Copilot, your AI design assistant, to brainstorm and develop a new idea from concept to custom board design. Discuss requirements, generate architectures, research parts, and draw your schematic.

Learn how to use Copilot, your AI design assistant, to brainstorm and develop a new idea from concept to custom board design. Discuss requirements, generate architectures, research parts, and draw your schematic.

Learn how to use Copilot, your AI design assistant, to brainstorm and develop a new idea from concept to custom board design. Discuss requirements, generate architectures, research parts, and draw your schematic.

Learn how to use Copilot, your AI design assistant, to brainstorm and develop a new idea from concept to custom board design. Discuss requirements, generate architectures, research parts, and draw your schematic.

Learn how to use Copilot, your AI design assistant, to brainstorm and develop a new idea from concept to custom board design. Discuss requirements, generate architectures, research parts, and draw your schematic.

Learn how to use Copilot, your AI design assistant, to brainstorm and develop a new idea from concept to custom board design. Discuss requirements, generate architectures, research parts, and draw your schematic.

Learn how to use Copilot, your AI design assistant, to brainstorm and develop a new idea from concept to custom board design. Discuss requirements, generate architectures, research parts, and draw your schematic.

Learn how to use Copilot, your AI design assistant, to brainstorm and develop a new idea from concept to custom board design. Discuss requirements, generate architectures, research parts, and draw your schematic.

Learn how to use Copilot, your AI design assistant, to brainstorm and develop a new idea from concept to custom board design. Discuss requirements, generate architectures, research parts, and draw your schematic.

Learn how to use Copilot, your AI design assistant, to brainstorm and develop a new idea from concept to custom board design. Discuss requirements, generate architectures, research parts, and draw your schematic.