Nice — you can do a clean pulse + latch using a single quad Schmitt-NAND chip: 74HC132 (or 74LVC132 for 3.3 V systems). The HC132 contains four 2-input NAND gates with Schmitt inputs so you can both clean a noisy SYN480R DATA line and build an SR latch (NAND SR is active-LOW) inside one package. Only a few passives and a driver transistor are needed. Below is a ready-to-build recipe (parts, wiring, explanation, tuning tips, and an ASCII schematic) — no extra logic ICs required. Parts (per latch) 1 × 74HC132 (quad 2-input NAND with Schmitt inputs). If your system is 3.3 V use 74LVC132 / 74HC132 rated for 3.3 V. Rin = 47 kΩ (input series) Cfilter = 10 nF (input RC to ground) — tweak for debounce/clean time Rpulldown = 100 kΩ (pull-down at input node, optional) Rpullup = 100 kΩ (pull-up for active-LOW R input so reset is idle HIGH) Rbase = 10 kΩ, Q = 2N2222 (NPN) or small N-MOSFET (2N7002) to drive your load Diode for relay flyback (1N4001) if you drive a coil Optional small cap 0.1 µF decoupling at VCC of IC Concept / how it works (short) Use Gate1 (G1) of 74HC132 as a Schmitt inverter by tying its two inputs together and feeding a small RC filter from SYN480R.DATA. This removes HF noise and provides a clean logic transition. Because it's a NAND with tied inputs its function becomes an inverter with Schmitt behavior. Use G2 & G3 as the cross-coupled NAND pair forming an SR latch (active-LOW inputs S̄ and R̄). A low on S̄ sets Q = HIGH. A low on R̄ resets Q = LOW. Wire the cleaned/inverted output of G1 to S̄. A valid received pulse (DATA high) produces a clean LOW on S̄ (because G1 inverts), setting the latch reliably even if the pulse is brief. R̄ is your reset input (pushbutton, HT12D VT, MCU line, etc.) — idle pulled HIGH. Q drives an NPN/MOSFET to switch your load (relay, LED, etc.). Recommended wiring (pin mapping, assume one chip; use datasheet pin numbers) I’ll refer to the 4 gates as G1, G2, G3, G4. Use G4 optionally for additional conditioning or to build a toggler later. SYN480R.DATA --- Rin (47k) ---+--- Node A ---||--- Cfilter (10nF) --- GND | Rpulldown (100k) --- GND (optional, keeps node low) Node A -> both inputs of G1 (tie inputs A and B of Gate1 together) G1 output -> S̄ (S_bar) (input1 of Gate2) Gate2 (G2): inputs = S̄ and Q̄ -> output = Q Gate3 (G3): inputs = R̄ and Q -> output = Q̄ R̄ --- Rpullup (100k) --- VCC (reset is idle HIGH; pull low to reset) (optional) R̄ can be wired to a reset pushbutton to GND or to an MCU pin Q -> Rbase (10k) -> base of 2N2222 (emitter GND; collector to one side of relay coil) Other side of relay coil -> +V (appropriate coil voltage) Diode across coil If you prefer MOSFET low side switching: Q -> gate resistor 100Ω -> gate of 2N7002 2N7002 source -> GND ; drain -> relay coil low side

Controlling a motor with attiny85 and a MOSFET transistor has never been easier! Communicate with your attiny85 through UART to send commands to the motor. #attiny85 #MOSFET #motorcontrol #UART

N-Channel 100V 57A (Tc) 200W (Tc) Through Hole TO-220AB #Commonpartslibrary #Transistor #MOSFET #FET #tht

The BSS138DW, manufactured by Diodes Incorporated, is a dual N-channel enhancement mode field-effect transistor (MOSFET) designed for high efficiency power management applications. This component features a low on-state resistance (RDS(on)) of 3.5 ohms at VGS = 10V and can handle a maximum drain current (ID) of 200mA at an ambient temperature of 25°C. With a drain-source voltage (V(BR)DSS) of 50V, the BSS138DW is ideal for load switching applications. The MOSFET offers superior switching performance with low gate threshold voltage, low input capacitance, and fast switching speed. It is fully compliant with RoHS standards and is available in a SOT-363 package. The component is also available in an automotive-compliant version under the part number BSS138DWQ, meeting AEC-Q101 standards for high reliability.

N-Channel 100V 320mA (Ta) 700mW (Ta) Through Hole TO-92 #CommonPartsLibrary #Transistor #Mosfet #N-Channel #FET #ZVN2110

The EMF30N02J from Excelliance MOS Corporation is an N-Channel Logic Level Enhancement Mode Field Effect Transistor designed for high efficiency and performance in a compact SOT-23 package. With a maximum Drain-Source voltage (BVDSS) of 20V and a maximum Drain current (ID) of 5A at 25°C, this MOSFET is ideal for low-voltage switching applications. It features a low maximum Drain-Source On-State Resistance (RDSON) of 30mΩ at a Gate-Source voltage (VGS) of 4.5V, ensuring minimal power dissipation. The component supports a Gate-Source voltage (VGS) up to +12V and operates within a temperature range of -55°C to 150°C. The EMF30N02J is also Pb-Free, Halogen-Free, and classified as a GP Green Product, making it environmentally friendly. Key electrical characteristics include a Gate Threshold Voltage (VGS(th)) between 0.45V and 1.2V, a maximum Gate-Body Leakage (IGSS) of 100nA, and a typical Forward Transconductance (gfs) of 7S. Additionally, the MOSFET exhibits excellent dynamic performance with a total Gate Charge (Qg) of 6.2nC, making it suitable for high-speed switching applications. The thermal resistance is rated at 100°C/W from junction-to-ambient and 55°C/W from junction-to-lead, ensuring efficient thermal management.