A simple load switch module to switch between Battery and 5V power

A simple load switch module to switch between Battery and 5V power

Welcome to your new project. Imagine what you can build here.

External Input Sensor Amplifier LOAD CELL AMP HX711 #commonpartslibrary #sensor #transducer #amplifier #loadcellamp

Linear Voltage Regulator IC Positive Fixed 1 Output 600mA SOT-25 3.3V LDO AP2112K-3.3 The AP2112K-3.3TRG1 is a low dropout (LDO) linear voltage regulator designed to provide a stable 3.3V output from a higher input voltage. It is optimized for low noise, high power supply rejection ratio (PSRR), and low quiescent current, making it suitable for battery-powered and noise-sensitive applications. The device features current limiting and thermal shutdown protection, ensuring reliable operation under fault conditions. It is commonly used in portable electronics, RF modules, microcontroller power supplies, and other low-power systems. Key Features Fixed output voltage: 3.3V Output current: up to 600 mA Low dropout voltage: ~250 mV at 300 mA load High PSRR: up to 70 dB at 1 kHz Low quiescent current: typically 55 µA Stable with low ESR ceramic capacitors Built-in overcurrent protection Thermal shutdown protection Fast transient response Absolute Maximum Ratings Input Voltage (VIN): up to 6.5 V Output Current: Internally limited Operating Junction Temperature: -40°C to +125°C Storage Temperature: -65°C to +150°C Electrical Characteristics (Typical values unless otherwise specified) Output Voltage Accuracy: ±2% Dropout Voltage: 250 mV @ 300 mA 400 mV @ 600 mA Line Regulation: 0.05%/V Load Regulation: 0.2% Quiescent Current: 55 µA Shutdown Current: <1 µA PSRR: 70 dB @ 1 kHz 45 dB @ 10 kHz Pin Configuration (SOT-23-5 / SC-70-5) VIN – Input voltage GND – Ground EN – Enable (active high) NC – No connection VOUT – Regulated output (3.3V) Package Information Package Type: SOT-23-5 (TRG1 suffix indicates tape & reel) Mounting: Surface mount Small footprint suitable for compact PCB layouts Typical Applications Battery-powered devices Wireless modules (Wi-Fi, Bluetooth, RF) Microcontroller and FPGA power supplies Portable consumer electronics Sensor and analog circuits requiring low noise Compliance & Reliability RoHS compliant Lead-free package Designed for high reliability and long operational life #CommonPartsLibrary #IntegratedCircuit #PowerManagement #LinearRegulator #VoltageRegulator

N-Channel 30 V 5.7A (Ta) 1.4W (Ta) Surface Mount SOT-23-3 The AO3400A N-Channel MOSFET is a 30V N-channel enhancement-mode MOSFET designed using trench MOSFET technology. It is widely used for load switching, DC-DC converters, motor driving, and PWM control applications due to its very low on-resistance and compact SOT-23 package. It is especially popular in small electronics and embedded systems because it can be driven directly by 3.3V or 5V logic signals, making it ideal for microcontroller-based designs. Key Features Drain-Source Voltage (VDS): 30V Continuous Drain Current (ID): up to 5.7A (at 25°C) Ultra-low RDS(on): ~26.5 mΩ @ VGS = 10V ~32 mΩ @ VGS = 4.5V ~48 mΩ @ VGS = 2.5V Logic-level gate drive (works well with MCU GPIOs) Fast switching performance (ns-range switching times) Low gate charge (~6–7 nC) → efficient switching Compact SOT-23 package for space-saving PCB design Low power dissipation (~1.4W typical at 25°C ambient) Operating temperature: −55°C to +150°C Typical Applications Load switching (LEDs, sensors, small motors) Power management in battery-powered devices DC-DC converters PWM control circuits Fan and heater control in embedded systems #AO3400A #MOSFET #NChannelMOSFET #PowerElectronics #SOT23 #LoadSwitch #EmbeddedSystems #ElectronicsComponents #TrenchMOSFET #Commonpartslibrary #Transistor #FET

Accelerometer X, Y, Z Axis ±2g, 4g, 8g, 16g 0.05Hz ~ 1.6kHz 14-LGA (3x5) The ADXL345 is a small, thin, ultralow power, 3-axis accelerometer with high resolution (13-bit) measurement at up to ±16 g. Digital output data is formatted as 16-bit twos complement and is accessible through either a SPI (3- or 4-wire) or I2C digital interface. The ADXL345 is well suited for mobile device applications. It measures the static acceleration of gravity in tilt-sensing applications, as well as dynamic acceleration resulting from motion or shock. Its high resolution (3.9 mg/LSB) enables measurement of inclination changes less than 1.0°. Several special sensing functions are provided. Activity and inactivity sensing detect the presence or lack of motion by comparing the acceleration on any axis with user-set thresholds. Tap sensing detects single and double taps in any direction. Free-fall sensing detects if the device is falling. These functions can be mapped individually to either of two interrupt output pins. An integrated memory management system with a 32-level first in, first out (FIFO) buffer can be used to store data to minimize host processor activity and lower overall system power consumption. Low power modes enable intelligent motion-based power management with threshold sensing and active acceleration measurement at extremely low power dissipation. The ADXL345 is supplied in a small, thin, 3 mm × 5 mm × 1 mm, 14-lead, plastic package. ► Ultralow power: as low as 23 µA in measurement mode and 0.1 µA in standby mode at VS = 2.5 V (typical) ► Power consumption scales automatically with bandwidth ► User-selectable resolution ► Fixed 10-bit resolution ► Full resolution, where resolution increases with g range, up to 13-bit resolution at ±16 g (maintaining 4 mg/LSB scale factor in all g ranges) ► Embedded memory management system with FIFO technology minimizes host processor load ► Single tap/double tap detection ► Activity/inactivity monitoring ► Free-fall detection ► Supply voltage range: 2.0 V to 3.6 V ► I/O voltage range: 1.7 V to VS ► SPI (3- and 4-wire) and I2C digital interfaces ► Flexible interrupt modes mappable to either interrupt pin ► Measurement ranges selectable via serial command ► Bandwidth selectable via serial command ► Wide temperature range (−40°C to +85°C) ► 10,000 g shock survival ► Pb free/RoHS compliant #commonpartslibrary #sensor #transducer #accelerometer

Bipolar (BJT) Transistor NPN 40V 200 mA 300MHz 300 mW Surface Mount SOT-23-3 (TO-236) The MMBT3904LT1G is a general-purpose NPN bipolar junction transistor designed for switching and amplification applications. It is housed in a compact SOT-23 surface-mount package, making it suitable for high-density PCB designs. This transistor is widely used in low-power signal processing, digital switching, and analog amplification circuits due to its reliable performance and fast switching characteristics. Key Features General-purpose NPN transistor Compact SOT-23 surface-mount package Fast switching speed Low saturation voltage Suitable for low-current and low-power applications High reliability and stability Pb-free, Halogen-free, and RoHS compliant Electrical Characteristics (Typical @ 25°C unless otherwise specified) Collector-Emitter Voltage (VCEO): 40 V Collector-Base Voltage (VCBO): 60 V Emitter-Base Voltage (VEBO): 6 V Collector Current (IC): 200 mA (max) DC Current Gain (hFE): 100 – 300 Collector-Emitter Saturation Voltage (VCE(sat)): 0.2 V (typ) Transition Frequency (fT): ~300 MHz Absolute Maximum Ratings Collector Current (Continuous): 200 mA Power Dissipation: ~225 mW Junction Temperature: +150°C (max) Operating Temperature Range: -55°C to +150°C Storage Temperature Range: -55°C to +150°C Mechanical Characteristics Package Type: SOT-23 (TO-236AB) Mounting Type: Surface Mount Number of Pins: 3 Marking Code: Dependent on lot/manufacturer marking Applications General-purpose switching circuits Signal amplification Digital logic interfacing LED drivers and small load switching Audio and RF signal processing #CommonPartsLibrary #TransistorBJT #MMBT2222

Automotive, 60-V, 6-A, 30-mΩ, one-channel smart high-side switch with adjustable current limit TPS1HTC30-Q1 is a single-channel, smart high-side switch, with integrated NMOS power FET and charge pump, designed to meet the requirements of 24-V automotive battery systems. The low RON(30 mΩ) minimizes device power dissipation driving a wide range of output load current up to 6-A DC, and the 60- V DC operating range improves system robustness. The device integrates protection features such as thermal shutdown, output clamp, and current limit. These features improve system robustness during fault events such as short circuit. TPS1HTC30-Q1 implements an adjustable current limiting circuit that improves the reliability of the system by reducing inrush current when driving large capacitive loads and minimizing overload current. The device also provides an accurate load current sense that allows for improved load diagnostics such as overload and open-load detection enabling better predictive maintenance. TPS1HTC30-Q1 is available in a small 14-pin, 4.40- mm × 5.0-mm HTSSOP leaded package with 0.65- mm pin pitch minimizing the PCB footprint. • Single-channel smart high-side power switch for 24-V automotive systems with full diagnostics • Wide operating voltage range: 6 V to 60 V – OVP protection: 66 V • Low RON: 30-mΩ typical, 55-mΩ maximum • Low standby current: < 0.5 µA • Low quiescent current (Iq): < 2 mA • Improve system level reliability through adjustable current limiting – Current limit: 2 A –16 A • Accurate current sensing: ±4% at 1 A • Protection – Overload and short-circuit protection – Integrated inductive discharge clamp – Undervoltage lockout (UVLO) protection – Loss of GND, loss of supply protection – Reverse battery protection with external components • Diagnostics – On and off state output open-load and short-tobattery detection – Overload and short to ground detection – Absolute and relative thermal shutdown detection • Functional Safety-Capable – Documentation available to aid functional safety system design • Operating junction temperature: –40 to 125°C • Input control: 1.8-V, 3.3-V and 5-V logic compatible • Integrated fault sense voltage scaling for ADC protection • Qualifications – AEC-Q100 qualified for automotive applications • Temperature grade 1: –40°C to +125°C, TA • 14-pin thermally-enhanced TSSOP package TPS1HTC30AQPWPRQ1 #CommonPartsLibrary #IntegratedCircuit

Telecom Relay DPDT (2 Form C) Through Hole The G6K-2P-Y DC5 is a compact, ultra-miniature signal relay designed for high-density PCB mounting applications. Manufactured by Omron, this relay features a DPDT (2 Form C) contact configuration and operates with a 5 VDC coil. It is optimized for switching low-level signals and is commonly used in telecommunications, test and measurement equipment, and consumer electronics where space-saving and high reliability are critical. Key Features Ultra-miniature, low-profile design for high-density mounting DPDT (2 Form C) contact configuration High sensitivity coil (low power consumption) Gold-clad contacts for low-level signal switching High reliability and long mechanical life Fully sealed construction (flux protection) Suitable for surface-mount and through-hole variants (depending on suffix) Electrical Characteristics Coil Specifications Rated Coil Voltage: 5 VDC Coil Resistance: ~125 Ω Coil Current: ~40 mA Power Consumption: ~200 mW Must Operate Voltage: ≤ 75% of rated voltage Must Release Voltage: ≥ 10% of rated voltage Contact Specifications Contact Configuration: DPDT (2 Form C) Contact Material: Gold-clad silver alloy Contact Rating: 1 A at 30 VDC 0.5 A at 125 VAC Maximum Switching Voltage: 125 VAC / 60 VDC Maximum Switching Current: 1 A Maximum Switching Power: 30 W (DC) 62.5 VA (AC) Timing Characteristics Operate Time: ≤ 3 ms Release Time: ≤ 3 ms Insulation Characteristics Insulation Resistance: ≥ 1,000 MΩ (at 500 VDC) Dielectric Strength: Between Coil and Contacts: 1,000 VAC (1 min) Between Open Contacts: 500 VAC (1 min) Mechanical Characteristics Mounting Type: Through-hole (Y variant, PCB terminal) Weight: ~1 g Enclosure: Sealed (flux-resistant) Environmental Specifications Operating Temperature Range: -40°C to +70°C Storage Temperature Range: -40°C to +85°C Vibration Resistance: 10 to 55 Hz, 1.5 mm double amplitude Shock Resistance: 1,000 m/s² Life Expectancy Mechanical Life: ≥ 100 million operations Electrical Life: ≥ 100,000 operations (at rated load) Applications Telecommunications equipment Test and measurement instruments Audio signal routing Industrial control systems Consumer electronics Package Information Manufacturer: Omron Electronics Series: G6K Part Number: G6K-2P-Y DC5 #commonpartslibrary #relay

Electronic Fuse Regulator 5.3A 20-WQFN (3x4) The TPS25940LRVCR is a compact eFuse (electronic fuse) power management IC from Texas Instruments designed to provide advanced power-path protection and load management for systems such as SSDs, servers, storage devices, and embedded electronics. It integrates protection features like overcurrent limiting, reverse current blocking, overvoltage protection, and controlled startup sequencing into a single chip. Wide input voltage range: 2.7 V to 18 V Adjustable current limit: 0.6 A to 5.3 A Low ON resistance: 42 mΩ typical True reverse current blocking using back-to-back MOSFETs Programmable output slew rate (dV/dt control) for inrush current management Overvoltage and undervoltage protection Fault and Power-Good outputs for system monitoring Current monitor (IMON) output Low-power DevSleep support for SSD applications Fast reverse voltage shutdown (~1 µs) Operating temperature: −40°C to +125°C junction temperature Available in a compact 20-pin WQFN package Typical Applications PCIe / SATA / SAS SSDs and HDDs Enterprise servers and storage systems RAID controller cards Smart load switches Set-top boxes and gaming systems Backup power and holdup capacitor systems Component Category This component belongs to: Power Management IC (PMIC) More specifically: eFuse / Hot-swap / Load Switch IC Package Information Package type: 20-WQFN (3 mm × 4 mm) Mounting type: Surface Mount (SMD) #commonpartslibrary #integratedcircuit #powermanagement #currentregulation

Buck Switching Regulator IC Positive Fixed 3.3V 1 Output 2A SOT-23-6 Thin, TSOT-23-6 The AP63200/AP63201/AP63203/AP63205 is a 2A, synchronous buck converter with a wide input voltage range of 3.8V to 32V and fully integrates a 125mΩ high-side power MOSFET and a 68mΩ low-side power MOSFET to provide high-efficiency step-down DC/DC conversion. The AP63200/AP63201/AP63203/AP63205 device is easily used by minimizing the external component count due to its adoption of peak current mode control along with its integrated compensation network. The AP63200/AP63201/AP63203/AP63205 has optimized designs for Electromagnetic Interference (EMI) reduction. The converter features Frequency Spread Spectrum (FSS) with a switching frequency jitter of ±6%, which reduces EMI by not allowing emitted energy to stay in any one frequency for a significant period of time. It also has a proprietary gate driver scheme to resist switching node ringing without sacrificing MOSFET turn-on and turn-off times, which further erases highfrequency radiated EMI noise caused by MOSFET switching. The device is available in a low-profile, TSOT26 package. • VIN 3.8V to 32V • 2A Continuous Output Current • 0.8V ±1% Reference Voltage • 22µA Ultralow Quiescent Current • Switching Frequency o 500kHz: AP63200 and AP63201 o 1.1MHz: AP63203 and AP63205 • Pulse Width Modulation (PWM) Regardless of Output Load o AP63201 • Supports Pulse Frequency Modulation (PFM) o AP63200, AP63203, and AP63205 o Up to 80% Efficiency at 1mA Light Load o Up to 88% Efficiency at 5mA Light Load • Fixed Output Voltage o 3.3V: AP63203 o 5.0V: AP63205 • Proprietary Gate Driver Design for Best EMI Reduction • Frequency Spread Spectrum (FSS) to Reduce EMI • Precision Enable Threshold to Adjust UVLO • Protection Circuitry o Overvoltage Protection o Cycle-by-Cycle Peak Current Limit o Thermal Shutdown • 12V and 24V distributed power bus supplies • Flat screen TV sets and monitors • Power tools and laser printers • White goods and small home appliances • FPGA, DSP, and ASIC supplies • Home audios • Network systems • Set top boxes • Gaming consoles • Consumer electronics #commonpartslibrary #integratedcircuit #AP63203WU7 #BuckConverter #DCDCConverter #PowerManagement #VoltageRegulator #SynchronousBuck #EmbeddedSystems #IndustrialElectronics #PowerSupply #DiodesInc #3V3Power #ElectronicsDesign

10 µH Shielded Drum Core, Wirewound Inductor 7.5 A 30mOhm Max Nonstandard # Engineering Specification ## Product Name SRP1038A-100M ## General Description SRP1038A-100M is a shielded surface mount power inductor designed for use in high-efficiency DC-DC conversion and power management applications. The device is intended to support energy storage and current smoothing functions in switching regulator circuits, where stable inductance performance and low power loss are critical. The inductor utilizes a ferrite core construction with a shielded magnetic structure to minimize electromagnetic interference and reduce magnetic flux leakage. This enables improved circuit density and reduced noise coupling in compact electronic assemblies. The design is optimized for use in high current power conversion systems, including buck converters, point-of-load regulators, and distributed power architectures. The component is widely used in industrial, automotive, telecommunications, and embedded systems where reliable energy transfer, thermal stability, and efficient power delivery are required. Its surface mount form factor supports automated PCB assembly and compact system integration while maintaining mechanical robustness under thermal and electrical stress. The design emphasizes low direct current resistance, high current handling capability, and stable inductance behavior under load conditions. It is suitable for applications requiring efficient power conversion with minimal energy loss and stable electromagnetic performance. ## Functional Requirements ### Energy Storage The device shall store energy in a magnetic field during switching operation in power conversion circuits. ### Current Filtering The device shall smooth current ripple in switching regulator applications to maintain stable output conditions. ### Electromagnetic Shielding The device shall reduce electromagnetic interference through a shielded magnetic structure. ### Power Conversion Support The component shall support efficient operation in DC-DC conversion systems. ## Electrical Requirements ### Inductive Performance The device shall provide stable inductance characteristics suitable for power conversion and filtering applications. ### Low Loss Operation The inductor shall minimize resistive and core losses to improve overall system efficiency. ### High Current Capability The device shall support operation under elevated current conditions typical of switching power supplies. ### Thermal Stability The inductor shall maintain performance consistency under thermal loading and temperature variation. ## Mechanical Requirements ### Surface Mount Package The device shall be supplied in a surface mount configuration suitable for automated PCB assembly processes. ### Structural Integrity The component shall withstand mechanical stress during assembly, operation, and thermal cycling. ### PCB Integration The design shall support compact layout integration in multilayer printed circuit board systems. ## Environmental Requirements ### Operating Conditions The device shall operate reliably under conditions typical of industrial and embedded electronic systems. ### Thermal Performance The component shall maintain stable operation under continuous power cycling and heat generation. ### Storage and Handling The device shall retain structural and electrical integrity during storage, transportation, and handling. ## Quality Requirements ### Reliability The inductor shall provide consistent long-term performance under continuous electrical and thermal stress. ### Verification Electrical and thermal characteristics shall be validated through appropriate qualification and testing procedures. ### Compliance The product shall conform to applicable standards for magnetic components used in power electronics applications. ## Documentation Requirements Technical documentation shall include application guidance, layout recommendations for switching power designs, thermal considerations, electrical characteristics, and integration practices for DC-DC converter systems. ## Classification Tags #SRP1038A100M #PowerInductor #ShieldedInductor #SMDInductor #MagneticComponent #EnergyStorageInductor #DCDCConverter #BuckConverter #PowerElectronics #SMPSDesign #ElectromagneticCompatibility #EMIShielding #PCBDesign #ElectricalEngineering #EmbeddedPower #IndustrialElectronics #AutomotiveElectronics #CommonPartsLibrary #ComponentLibrary #EngineeringSpecification #PowerManagement #CircuitDesign #HighCurrentInductor