Welcome to your new project. Imagine what you can build here.

Nice — you can do a clean pulse + latch using a single quad Schmitt-NAND chip: 74HC132 (or 74LVC132 for 3.3 V systems). The HC132 contains four 2-input NAND gates with Schmitt inputs so you can both clean a noisy SYN480R DATA line and build an SR latch (NAND SR is active-LOW) inside one package. Only a few passives and a driver transistor are needed. Below is a ready-to-build recipe (parts, wiring, explanation, tuning tips, and an ASCII schematic) — no extra logic ICs required. Parts (per latch) 1 × 74HC132 (quad 2-input NAND with Schmitt inputs). If your system is 3.3 V use 74LVC132 / 74HC132 rated for 3.3 V. Rin = 47 kΩ (input series) Cfilter = 10 nF (input RC to ground) — tweak for debounce/clean time Rpulldown = 100 kΩ (pull-down at input node, optional) Rpullup = 100 kΩ (pull-up for active-LOW R input so reset is idle HIGH) Rbase = 10 kΩ, Q = 2N2222 (NPN) or small N-MOSFET (2N7002) to drive your load Diode for relay flyback (1N4001) if you drive a coil Optional small cap 0.1 µF decoupling at VCC of IC Concept / how it works (short) Use Gate1 (G1) of 74HC132 as a Schmitt inverter by tying its two inputs together and feeding a small RC filter from SYN480R.DATA. This removes HF noise and provides a clean logic transition. Because it's a NAND with tied inputs its function becomes an inverter with Schmitt behavior. Use G2 & G3 as the cross-coupled NAND pair forming an SR latch (active-LOW inputs S̄ and R̄). A low on S̄ sets Q = HIGH. A low on R̄ resets Q = LOW. Wire the cleaned/inverted output of G1 to S̄. A valid received pulse (DATA high) produces a clean LOW on S̄ (because G1 inverts), setting the latch reliably even if the pulse is brief. R̄ is your reset input (pushbutton, HT12D VT, MCU line, etc.) — idle pulled HIGH. Q drives an NPN/MOSFET to switch your load (relay, LED, etc.). Recommended wiring (pin mapping, assume one chip; use datasheet pin numbers) I’ll refer to the 4 gates as G1, G2, G3, G4. Use G4 optionally for additional conditioning or to build a toggler later. SYN480R.DATA --- Rin (47k) ---+--- Node A ---||--- Cfilter (10nF) --- GND | Rpulldown (100k) --- GND (optional, keeps node low) Node A -> both inputs of G1 (tie inputs A and B of Gate1 together) G1 output -> S̄ (S_bar) (input1 of Gate2) Gate2 (G2): inputs = S̄ and Q̄ -> output = Q Gate3 (G3): inputs = R̄ and Q -> output = Q̄ R̄ --- Rpullup (100k) --- VCC (reset is idle HIGH; pull low to reset) (optional) R̄ can be wired to a reset pushbutton to GND or to an MCU pin Q -> Rbase (10k) -> base of 2N2222 (emitter GND; collector to one side of relay coil) Other side of relay coil -> +V (appropriate coil voltage) Diode across coil If you prefer MOSFET low side switching: Q -> gate resistor 100Ω -> gate of 2N7002 2N7002 source -> GND ; drain -> relay coil low side

The electronic speed controller (ESC) is an essential part of an electric propulsion system’s hardware. It acts like the brain of the system by telling the motor how fast to go based on data signals it receives from the throttle controller. For smaller applications like drones and RC vehicles, this controller has the name ‘ESC’, whereas for larger manufacturing applications it may be called an electronic control unit, inverter, or motor controller. #drone #motorController #PCA9685 #controller #motor #esc #referenceDesign #project #EFM8BB21F16G #MPU9250 #template

@Copilot Quiero circuito para equipo de soldadura inverter de 15 a 300 amperios de salida, corriente directa. Con entrada de 110v y 240v corriente alterna. Con indicador Led de amperios.

Welcome to your new project. Imagine what you can build here.

Inverterschaltung

The inverter specs are Switching frequency: 200kHz Input voltage: 180VDC Output voltage: 120VAC Max power: 1500W I have designed an Inverter schematic for an uninterruptible power supply (UPS), Used an efficiency LCL topology filter to eliminate 3rd and 5th harmonics as induction motor is connected at load. The Inverter schematic that can convert 180VDC into 120VAC, which can be used in any household or industrial application. You can refer the BOM to check the MOSFET parts, drivers, and filter parameter values.

The inverter specs are Switching frequency: 200kHz Input voltage: 180VDC Output voltage: 120VAC Max power: 1500W I have designed an Inverter schematic for an uninterruptible power supply (UPS), Used an efficiency LCL topology filter to eliminate 3rd and 5th harmonics as induction motor is connected at load. The Inverter schematic that can convert 180VDC into 120VAC, which can be used in any household or industrial application. You can refer the BOM to check the MOSFET parts, drivers, and filter parameter values.

Welcome to your new project. Imagine what you can build here.

Welcome to your new project. Imagine what you can build here.

Welcome to your new project. Imagine what you can build here.

Welcome to your new project. Imagine what you can build here.

Welcome to your new project. Imagine what you can build here.

Changes direct current (DC) to alternating current (AC). See https://en.wikipedia.org/wiki/Power_inverter

Welcome to your new project. Imagine what you can build here.

Welcome to your new project. Imagine what you can build here.

Welcome to your new project. Imagine what you can build here.

Welcome to your new project. Imagine what you can build here.

Welcome to your new project. Imagine what you can build here.

Welcome to your new project. Imagine what you can build here.

Welcome to your new project. Imagine what you can build here.

Welcome to your new project. Imagine what you can build here.

24VDC Input 5kV Output MCU controlled 200kHz PWM Mosfet based inverter 6 stage multiplier Todo: Pick real inductor in load network Flyback Transformer with Ferrite core Selection

The electronic speed controller (ESC) is an essential part of an electric propulsion system’s hardware. It acts like the brain of the system by telling the motor how fast to go based on data signals it receives from the throttle controller. For smaller applications like drones and RC vehicles, this controller has the name ‘ESC’, whereas for larger manufacturing applications it may be called an electronic control unit, inverter, or motor controller. #drone #motorController #PCA9685 #controller #motor #esc #referenceDesign #project #EFM8BB21F16G #MPU9250 #template

The electronic speed controller (ESC) is an essential part of an electric propulsion system’s hardware. It acts like the brain of the system by telling the motor how fast to go based on data signals it receives from the throttle controller. For smaller applications like drones and RC vehicles, this controller has the name ‘ESC’, whereas for larger manufacturing applications it may be called an electronic control unit, inverter, or motor controller. #drone #motorController #PCA9685 #controller #motor #esc #referenceDesign #project #EFM8BB21F16G #MPU9250 #template

The electronic speed controller (ESC) is an essential part of an electric propulsion system’s hardware. It acts like the brain of the system by telling the motor how fast to go based on data signals it receives from the throttle controller. For smaller applications like drones and RC vehicles, this controller has the name ‘ESC’, whereas for larger manufacturing applications it may be called an electronic control unit, inverter, or motor controller. #drone #motorController #PCA9685 #controller #motor #esc #referenceDesign #project #EFM8BB21F16G #MPU9250 #template

Naze 32 Revision 6 Flight Controller Schematic At the heart of the Naze32 is a 32bit ST micro work horse of a processor, with untapped memory and cpu power and a host of equally impressive sensors. The Naze is also matched up with some of the nicest GUI programs and features to get the most out of your configuration. Naze32 rev6 Features: USB on right side PPM/PWM input as through-hole 3.3V, I2C on standard-size headers Fully pinout compatible with rev5 accessories (OSDoge etc) SBUS Inverter Spectrum satellite MPU6500 Sonar pads w/resistors added for direct connection to 5V sonar All extra pads (FT, GP, A5) on top, only sonar on bottom BMP280 barometer 16mbit flash Guide: https://www.dronetrest.com/t/naze-32-revision-6-flight-controller-guide/1605

The electronic speed controller (ESC) is an essential part of an electric propulsion system’s hardware. It acts like the brain of the system by telling the motor how fast to go based on data signals it receives from the throttle controller. For smaller applications like drones and RC vehicles, this controller has the name ‘ESC’, whereas for larger manufacturing applications it may be called an electronic control unit, inverter, or motor controller. #drone #motorController #PCA9685 #controller #motor #esc #referenceDesign #project #EFM8BB21F16G #MPU9250 #template

Naze 32 Revision 6 Flight Controller Schematic At the heart of the Naze32 is a 32bit ST micro work horse of a processor, with untapped memory and cpu power and a host of equally impressive sensors. The Naze is also matched up with some of the nicest GUI programs and features to get the most out of your configuration. Naze32 rev6 Features: USB on right side PPM/PWM input as through-hole 3.3V, I2C on standard-size headers Fully pinout compatible with rev5 accessories (OSDoge etc) SBUS Inverter Spectrum satellite MPU6500 Sonar pads w/resistors added for direct connection to 5V sonar All extra pads (FT, GP, A5) on top, only sonar on bottom BMP280 barometer 16mbit flash Guide: https://www.dronetrest.com/t/naze-32-revision-6-flight-controller-guide/1605

Etapa 1: Recolección y Almacenamiento de Energía Entrada: tus cactus en serie (ej. 15 cactus × 0.5 V = 7.5 V). Componente clave: Supercapacitor o batería recargable de baja capacidad (Li-ion o LiFePO4, 3.7V-7.4V). Diodo Schottky entre los cactus y el capacitor para evitar descarga inversa. 🛠 Ejemplo de componentes: Supercapacitor de 5–10 F, 5.5 V o batería de 3.7 V (tipo 18650). Diodo Schottky 1N5819. Módulo cargador TP4056 (si usas batería). Etapa 2: Aumento de Voltaje (Boost Converter) Conversión de 3.7 V / 7.5 V DC a 110 V AC. Necesitas: Boost Converter (DC-DC Step-up) de hasta 300 V DC. Inversor DC-AC (pequeño, tipo mini inverter para LEDs) que convierta ese voltaje a 110 V AC. NOTA: Algunos focos LED pueden funcionar con 110 V DC directamente, si quieres evitar el inversor. Etapa 3: Detección de Noche Sensor LDR (resistor dependiente de luz) conectado a un comparador (ej. LM393) o a un microcontrolador (como un ATtiny o ESP8266 si quieres funciones extra). Al bajar la luz solar: El comparador activa un MOSFET o un relé que conecta la energía almacenada al foco.

The electronic speed controller (ESC) is an essential part of an electric propulsion system’s hardware. It acts like the brain of the system by telling the motor how fast to go based on data signals it receives from the throttle controller. For smaller applications like drones and RC vehicles, this controller has the name ‘ESC’, whereas for larger manufacturing applications it may be called an electronic control unit, inverter, or motor controller. #drone #motorController #PCA9685 #controller #motor #esc #referenceDesign #project #EFM8BB21F16G #MPU9250 #template

Naze 32 Revision 6 Flight Controller Schematic At the heart of the Naze32 is a 32bit ST micro work horse of a processor, with untapped memory and cpu power and a host of equally impressive sensors. The Naze is also matched up with some of the nicest GUI programs and features to get the most out of your configuration. Naze32 rev6 Features: USB on right side PPM/PWM input as through-hole 3.3V, I2C on standard-size headers Fully pinout compatible with rev5 accessories (OSDoge etc) SBUS Inverter Spectrum satellite MPU6500 Sonar pads w/resistors added for direct connection to 5V sonar All extra pads (FT, GP, A5) on top, only sonar on bottom BMP280 barometer 16mbit flash Guide: https://www.dronetrest.com/t/naze-32-revision-6-flight-controller-guide/1605

This project is a voltage comparator circuit utilizing an LM311DR comparator and an LM27762DSSR switched capacitor voltage inverter. The circuit takes an input signal, compares it with a reference voltage, and outputs a digital signal indicating which voltage is higher. #project

Naze 32 Revision 6 Flight Controller Schematic At the heart of the Naze32 is a 32bit ST micro work horse of a processor, with untapped memory and cpu power and a host of equally impressive sensors. The Naze is also matched up with some of the nicest GUI programs and features to get the most out of your configuration. Naze32 rev6 Features: USB on right side PPM/PWM input as through-hole 3.3V, I2C on standard-size headers Fully pinout compatible with rev5 accessories (OSDoge etc) SBUS Inverter Spectrum satellite MPU6500 Sonar pads w/resistors added for direct connection to 5V sonar All extra pads (FT, GP, A5) on top, only sonar on bottom BMP280 barometer 16mbit flash Guide: https://www.dronetrest.com/t/naze-32-revision-6-flight-controller-guide/1605

dc motor polarity inverter

Naze 32 Revision 6 Flight Controller Schematic At the heart of the Naze32 is a 32bit ST micro work horse of a processor, with untapped memory and cpu power and a host of equally impressive sensors. The Naze is also matched up with some of the nicest GUI programs and features to get the most out of your configuration. Naze32 rev6 Features: USB on right side PPM/PWM input as through-hole 3.3V, I2C on standard-size headers Fully pinout compatible with rev5 accessories (OSDoge etc) SBUS Inverter Spectrum satellite MPU6500 Sonar pads w/resistors added for direct connection to 5V sonar All extra pads (FT, GP, A5) on top, only sonar on bottom BMP280 barometer 16mbit flash Guide: https://www.dronetrest.com/t/naze-32-revision-6-flight-controller-guide/1605

Welcome to your new project. Imagine what you can build here.

Welcome to your new project. Imagine what you can build here.

A smart ESP32-based battery management system controller board for Lithium ion battery packs/cells. Capable of communicating to wide varieties of hybrid-smart inverters with CANbus, RS485 and UART communication.

A smart ESP32-based battery management system controller board for Lithium ion battery packs/cells. Capable of communicating to wide varieties of hybrid-smart inverters with CANbus, RS485 and UART communication. #smartHomeDevices

A smart ESP32-based battery management system controller board for Lithium ion battery packs/cells. Capable of communicating to wide varieties of hybrid-smart inverters with CANbus, RS485 and UART communication.

A smart ESP32-based battery management system controller board for Lithium ion battery packs/cells. Capable of communicating to wide varieties of hybrid-smart inverters with CANbus, RS485 and UART communication.

A smart ESP32-based battery management system controller board for Lithium ion battery packs/cells. Capable of communicating to wide varieties of hybrid-smart inverters with CANbus, RS485 and UART communication. #smartHomeDevices

A smart ESP32-based battery management system controller board for Lithium ion battery packs/cells. Capable of communicating to wide varieties of hybrid-smart inverters with CANbus, RS485 and UART communication. #smartHomeDevices

A smart ESP32-based battery management system controller board for Lithium ion battery packs/cells. Capable of communicating to wide varieties of hybrid-smart inverters with CANbus, RS485 and UART communication.

A smart ESP32-based battery management system controller board for Lithium ion battery packs/cells. Capable of communicating to wide varieties of hybrid-smart inverters with CANbus, RS485 and UART communication. #smartHomeDevices

A smart ESP32-based battery management system controller board for Lithium ion battery packs/cells. Capable of communicating to wide varieties of hybrid-smart inverters with CANbus, RS485 and UART communication.

The analog car design is a self-running electric car that avoids obstacle in the left-right region. The design is mainly supported with 5 circuit components. The 9 V to 5 V converted for voltage-current manipulations. The push-button delay circuit (kill switch) for users to temporarily be able to stop the car motors benefiting from RC circuit, MOSFET transistors, and 74HC14 Hex Schmitt Trigger Inverters. The motor speed controller using potentiometers, inverters, and generic diodes. As well as the HC-SR04 Ultrasonic Sensor circuit to sense the proximity of objects in a field of view.

A smart ESP32-based battery management system controller board for Lithium ion battery packs/cells. Capable of communicating to wide varieties of hybrid-smart inverters with CANbus, RS485 and UART communication.

A smart ESP32-based battery management system controller board for Lithium ion battery packs/cells. Capable of communicating to wide varieties of hybrid-smart inverters with CANbus, RS485 and UART communication.