A Tesla coil is an electrical resonant transformer circuit designed by inventor Nikola Tesla in 1891. It is used to produce high-voltage, low-current, high frequency alternating-current electricity. Tesla experimented with a number of different configurations consisting of two, or sometimes three, coupled resonant electric circuits.

Welcome to your new project. Imagine what you can build here.

Multiple High Voltage Sources from Single Class D Amplifier Input Input: 48V 2.5kW Output: 5kV 2kW

A Tesla coil is an electrical resonant transformer circuit designed by inventor Nikola Tesla in 1891. It is used to produce high-voltage, low-current, high frequency alternating-current electricity. Tesla experimented with a number of different configurations consisting of two, or sometimes three, coupled resonant electric circuits.

A Tesla coil is an electrical resonant transformer circuit designed by inventor Nikola Tesla in 1891. It is used to produce high-voltage, low-current, high frequency alternating-current electricity. Tesla experimented with a number of different configurations consisting of two, or sometimes three, coupled resonant electric circuits.

Premium dual-PCB ESP32 smart water level controller with isolated high-voltage power/motor board, low-voltage IoT logic board, level sensing, dry-run/voltage/current protection, TFT UI, MQTT connectivity, RTC logging, and industrial surge protection.

High-fidelity high-voltage amplifier for 2.5 nF ultrasonic piezo transducer, 10 V input, gain 40, up to 400 V peak single-ended output from 220 VAC with 3 A peak overcurrent protection and China-preferred component sourcing.

220VAC-powered high-voltage arbitrary waveform amplifier targeting ±1000Vpeak into 2.5nF, 0–500kHz, ≥10A peak with ≤4000V/µs slew-rate limit; component selection prioritizes China-made / China-supply-chain parts where safe and technically suitable.

Partitioned Tesla coil system with separate high-voltage power stage and low-voltage control board, designed around a fixed secondary coil and reuse of an external bridge rectifier and 5500 uF 450 VDC bulk capacitor where applicable.

Single-project implementation of the Blue Ant AMP Architecture Rev2 using one shared schematic with six logical board partitions: PCB-01 phono stage, PCB-02 input selector and relay attenuator interface, PCB-03 balanced driver and RCA-to-balanced conversion interface, PCB-04 dual logical power amplifier channels, PCB-05 multi-rail power supply, and PCB-06 isolated control and display. Explicit inter-partition connector interfaces and named nets preserve balanced signal handling after RCA conversion, distinct rail domains (+63V, -63V, +15V, -15V, +5V, +3.3V), and documented hard constraints including low-noise analog isolation and high-voltage domain separation.

96-Channel, 12-Bit, Low-Power, Serial-Input, High-Voltage Output DAC with Conversion Trigger

This project is focused on designing a highly efficient PCB for a switching power supply using a robust selection of electronic components. Our design leverages a flyback topology featuring a ferrite transformer (options EE25 or EE33), a PWM integrated circuit (TL494, SG3525, or UC3842), and a power MOSFET (IRF840 or a similar alternative) for effective high-voltage switching. Fast and reliable rectification is ensured by using a Schottky diode (MBR20100 or FR107) along with a rectifier bridge built from four 1N4007 diodes or a dedicated 4A bridge. Key stabilization and regulation components include the TL431 reference regulator and a Zener diode for precise voltage control in critical areas. For input and output filtering, the design incorporates electrolytic capacitors (470 µF, 25 V for output and 400 V, 100 µF for input) and ceramic capacitors (ranging from 1 nF to 100 nF) to limit high-frequency noise. Additional safety and operational features are provided by an NTC (soft-start thermistor) to prevent current spikes, various resistors (from 1 Ω to 100kΩ), an optocoupler (PC817) for signal isolation, a switch, and a protection fuse. Before moving forward with a finalized PCB layout and schematic details, we need to clarify a few design choices: 1. Transformer Choice: Would you prefer using the EE25 or the EE33 ferrite transformer variant as the heart of the switching power supply design? This detailed approach ensures that the power supply not only meets rigorous performance and safety standards but also supports a reliable and scalable solution for various electronic applications. #PCBDesign #SwitchingPowerSupply #Electronics #SMPS #PowerElectronics #FlybackConverter #CircuitDesign #ElectronicsComponents

24VDC Input 5kV Output MCU controlled 200kHz PWM Mosfet based inverter 6 stage multiplier Todo: Pick real inductor in load network Flyback Transformer with Ferrite core Selection

Welcome to your new project. Imagine what you can build here.