USB-powered isolated listen-only NMEA 2000/CAN gateway that forwards boat network data over Wi-Fi to an iPad web dashboard. Prototype prioritizes bus safety: no termination, isolated CAN, and hardware-disabled TX path.

Isolated 220 VAC to 5 V / 2 A power supply using a certified AC-DC module, with potentiometer-controlled PWM output for a 5 V load. Includes mains input protection and safety documentation assumptions.

Low-voltage DC distribution board for an Australian faceplate: 24V input with fused 24V pass-through and isolated 12V/5A conversion feeding three individually protected 12V outputs in a 75 × 75 mm envelope.

AutoPilot V4.0 C.O.R.E. Brain Box Rev D for Vermeer D20x22 HDD, with isolated CM4, relay, and 24V safety domains, I2C DAC/ADC control, relay driver cells, and Deutsch harness connectors.

Industrial ESP32-S3 master gateway with Ethernet (W5500), LoRa 433 MHz, microSD storage, RTC, USB-UART console/debug interface (CP2102N), and isolated RS485 ports using ADM2587 transceivers. The design includes ESP32-S3-WROOM-1-N16R2 as the main controller, W5500 Ethernet, LoRa antenna interface, microSD connector, RTC circuitry, CP2102N USB-to-UART programming/debug console, SC16IS752 UART expanders, isolated RS485 channels, power regulation, ESD/surge protection, connectors, and mounting holes. Cellular/BG95/SIM functionality and true RS232 console hardware are not included; J1 is used only as the microSD card connector.

2-layer 415V agricultural motor starter controller with STM32, 4G modem, relay control, current/voltage sensing, and isolated field inputs.

ESP32-S3 Industrial PLC Controller schematic architecture for a 24 V industrial PLC with W5500 Ethernet, isolated RS485, 8 opto-isolated digital inputs, and 8 protected high-side outputs.

IP67 Australian 240 VAC spa-light controller focused on isolated SELV control electronics, optical programming, hold-up power, mains-present sensing, and relay coil drivers.

Industrial 24 V DC MESBox controller with embedded Linux SOM, STM32 real-time I/O, triple RJ45 Ethernet, TFT display, isolated inputs, protected transistor outputs, offline memory, surge/reverse-polarity protection, and EMC-focused layout constraints.

Custom 4S CATL NCM module BMS/CMU sampling and passive balancing board for a Toyota Prius hybrid battery retrofit using BM3451SMDC-T28A with isolated CO/DO fault outputs and M4 sense studs.

STM32F103-based GLECS V4 pure logic controller with 12V input power tree, onboard 4G module, isolated relay control zone, sensors, OLED, debug headers, and 200x140mm two-layer PCB requirements.

Custom 4S CATL NCM module BMS/CMU sampling and passive balancing board for a Toyota Prius hybrid battery retrofit using BM3451SMDC-T28A with isolated CO/DO fault outputs and M4 sense studs.

Minimal ESP32 and PC817 optocoupler schematic for an isolated WiFi-controlled PC motherboard power-switch interface.

Industrial 415V 3-phase motor control interface with STM32 command logic, SIMCom A7672S 4G SMS control, isolated relay driver, 12V input power, and 150x100mm 2-layer PCB constraints.

Custom 4S CATL NCM module BMS/CMU sampling and passive balancing board for a Toyota Prius hybrid battery retrofit using BM3451SMDC-T28A with isolated CO/DO fault outputs and M4 sense studs.

Industrial motor controller PCB with 12V relay switching zone isolated from STM32/4G LTE logic zone by a routed vertical isolation slot on a 150x100mm 2-layer FR4 board.

Custom 4S CATL NCM module BMS/CMU sampling and passive balancing board for a Toyota Prius hybrid battery retrofit using BM3451SMDC-T28A with isolated CO/DO fault outputs and M4 sense studs.

Custom 4S CATL NCM module BMS/CMU sampling and passive balancing board for a Toyota Prius hybrid battery retrofit using BM3451SMDC-T28A with isolated CO/DO fault outputs and M4 sense studs.

Custom 4S CATL NCM module BMS/CMU sampling and passive balancing board for a Toyota Prius hybrid battery retrofit using BM3451SMDC-T28A with isolated CO/DO fault outputs and M4 sense studs.

Custom 4S CATL NCM module BMS/CMU sampling and passive balancing board for a Toyota Prius hybrid battery retrofit using BM3451SMDC-T28A with isolated CO/DO fault outputs and M4 sense studs.

Fully integrated Arduino Uno shield with 13.56 MHz RFID reader, microSD card interface, isolated relay output for a 120 VAC signal circuit, and 28 VDC to 5 V buck power input.

Custom 4S CATL NCM module BMS/CMU sampling and passive balancing board for a Toyota Prius hybrid battery retrofit using BM3451SMDC-T28A with isolated CO/DO fault outputs and M4 sense studs.

Custom 4S CATL NCM module BMS/CMU sampling and passive balancing board for a Toyota Prius hybrid battery retrofit using BM3451SMDC-T28A with isolated CO/DO fault outputs and M4 sense studs.

Custom 4S CATL NCM module BMS/CMU sampling and passive balancing board for a Toyota Prius hybrid battery retrofit using BM3451SMDC-T28A with isolated CO/DO fault outputs and M4 sense studs.

Custom 4S CATL NCM module BMS/CMU sampling and passive balancing board for a Toyota Prius hybrid battery retrofit using BM3451SMDC-T28A with isolated CO/DO fault outputs and M4 sense studs.