This project is a controller module that uses the ESP32-WROOM-32E and the MAX3485 to communicate with Modbus devices. It has a USB-C port for power and data, a voltage regulator for stable operation. It also has a CH340C chip for USB to serial conversion. #referenceDesign #project #ESP32 #ESP32WROOM #RF #WIFI #MCU #reusable #module #simple-embedded #espressif #template #MAX3485 #RS485 #maximintegrated

This project is a Pulse Width Modulation (PWM) Controller, built around an LM555 timer IC. It controls a load connected to a MOSFET, with adjustments via a potentiometer, and uses capacitors, resistors and diodes for various functions. #PWM #controller #project #Template #projectTemplate

DIN-rail ESP32-S3 mains-powered controller with isolated 5 V supply, Ethernet RJ45, USB-C service port, and central LED module connector.

Industrial ESP32-based mains-powered controller with 220 VAC input, isolated 5 V supply, 8 SSR-controlled high-current AC output channels, and a single RTD temperature input. Layout and safety constraints must preserve reinforced isolation and separation between hazardous mains/high-current paths and low-voltage control circuitry.

Golf ball dispenser controller with protected 12V-24V DC input, LM2596 5V buck, ESP32 control, INA219 relay-coil sensing, and dry-contact relay output.

ESP32-S3 quadcopter flight controller with OV5640 24-pin DVP camera interface, Wi-Fi video link, BLE telemetry, onboard USB-C power/programming, IMU, barometer, ToF altitude sensing, lidar connector, and 4 ESC PWM outputs.

Industrial ESP32-C3 controller board with isolated RS-485, protected 12V-24V input, opto-isolated digital inputs, sensor interfaces, and production debug header.

Compact ESP32-S3 AI robot controller with DevKitC-1 module, 2S Li-ion power input, 5V buck regulator, optional clean 3.3V rail, TB6612FNG dual motor driver, OV2640 camera FPC, I2S audio, OLED, ultrasonic and TCRT5000 sensor headers, and a compact 2-layer PCB prepared for Gerber export.

High-power wind turbine charging controller that boosts a 20-40 V, up to 2000 W turbine source to charge a 48 V power bank with sensing, intelligent operating-mode control, and protection including diversion handling.

Modular ESP32 dev-board smart photobioreactor controller with 12 V input protection, 5 V buck conversion, 3.3 V regulation, connectorized sensors and actuators, I2C LCD and RTC, SPI SD logging, GPIO breakout, test points, and prototype-friendly high-power/low-power partitioning.

Multi-layer circular BLDC motor controller for a 24 V, up to 750 W system using an ESP32-WROOM with DRV8323RS gate driver, six external MOSFETs, 2 mOhm shunt current sensing, bottom-mounted AS5600 encoder, USB-C programming/user interface, 3.3 V logic powered from the DRV8323RS buck regulator, and heavy motor phase pads sized for approximately 30 A current paths. Target layout is a circular board around 50 mm diameter, expandable if required for thermal management, power routing, and signal integrity.

Automotive smart fuel pump controller with >12 V battery qualification, protected battery input, analog FSCM command following, 25 A current sensing, thermal/fault indication, blue/red LED signaling, and 5-second buzzer alert. Control and fault nets are explicitly terminated to avoid floating or undriven states; any intentionally provisional control nodes are weakly biased to safe defaults during refinement.

ESP32-S3 door access controller with USB-C Li-ion charging, VBAT and 12V lock power, dual 3.3V rails, I2C sensor headers, reed/PIR inputs, LED indicators, buzzer, and MOSFET plus relay lock outputs. External modules and field devices remain represented by connector placeholders with documented pinouts for later PCB and validation work.

Industrial-grade embedded I/O controller schematic with 9-36V protected input, 5V buck, 3.3V logic, STM32F103C8T6 MCU, industrial dry/wet/pulse/analog inputs, 12V semiconductor-switched output, RS-485/UART communications, external watchdog, SWD/debug features, and interview-ready engineering notes.

Bluetooth RC car controller using ESP32-WROOM-32E, TB6612FNG dual H-bridge, XL4015 5V buck module, DC barrel battery input, dual 2-pin motor screw terminals, 1000uF VM bulk capacitor, 100nF decoupling, 10k EN pull-up, 30 mil power traces, 10 mil signal traces, and ESP32 antenna edge keep-out.

This is a STM32F4 Flight Controller template with 6-axis Accelerometer, Gyroscope. With OSD generator MAX7456EUI. #drone #flightController #STM32F405 #controller #OSD #video #referenceDesign #project #MPU6000 #template

This is a STM32F4 Flight Controller template with 6-axis Accelerometer, Gyroscope. With OSD generator MAX7456EUI. #drone #flightController #STM32F405 #controller #OSD #video #referenceDesign #project #MPU6000 #template

This is a STM32F4 Flight Controller template with 6-axis Accelerometer, Gyroscope. With OSD generator MAX7456EUI. #drone #flightController #STM32F405 #controller #OSD #video #referenceDesign #project #MPU6000 #template

This is a STM32F4 Flight Controller template with 6-axis Accelerometer, Gyroscope. With OSD generator MAX7456EUI. #drone #flightController #STM32F405 #controller #OSD #video #referenceDesign #project #MPU6000 #template

A universal pellet stove controller that uses and arduino uno as the mcu and the

A smart ESP32-based battery management system controller board for Lithium ion battery packs/cells. Capable of communicating to wide varieties of hybrid-smart inverters with CANbus, RS485 and UART communication. Inspired by the open-source project diyBMS by Stuart Pittaway #smartHomeDevices #esp32 #iot

Kiln controller thermocouple hat

This is a VGA signal generation based on ICE40 Field-programmable gate array chip #VGA #FPGA #ICE40HX1K #ICE40 #controller #referenceDesign #project #template #SRAM #video #display

This is a STM32F4 Flight Controller template with 6-axis Accelerometer, Gyroscope. With OSD generator MAX7456EUI. #drone #flightController #STM32F405 #controller #OSD #video #referenceDesign #project #MPU6000 #template

This project is a controller module that uses the ESP32-WROOM-32E and the MAX3485 to communicate with Modbus devices. It has a USB-C port for power and data, a voltage regulator for stable operation. It also has a CH340C chip for USB to serial conversion. #referenceDesign #project #ESP32 #ESP32WROOM #RF #WIFI #MCU #reusable #module #simple-embedded #espressif #template #MAX3485 #RS485 #maximintegrated

This project is a Pulse Width Modulation (PWM) Controller, built around an LM555 timer IC. It controls a load connected to a MOSFET, with adjustments via a potentiometer, and uses capacitors, resistors and diodes for various functions. #PWM #controller #project #Template #projectTemplate

plumbing controller

This project is a controller module that uses the ESP32-WROOM-32E and the MAX3485 to communicate with Modbus devices. It has a USB-C port for power and data, a voltage regulator for stable operation, and headers for connecting sensors and actuators. It also has a CH340C chip for USB to serial conversion. #referenceDesign #project #ESP32 #ESP32WROOM #RF #WIFI #MCU #referenceDesign #simple-embedded #espressif #template #MAX3485 #RS485 #maximintegrated #reference-design

This project is a controller module that uses the ESP32-WROOM-32E and the MAX3485 to communicate with Modbus devices. It has a USB-C port for power and data, a voltage regulator for stable operation. It also has a CH340C chip for USB to serial conversion. #referenceDesign #project #ESP32 #ESP32WROOM #RF #WIFI #MCU #reusable #module #simple-embedded #espressif #template #MAX3485 #RS485 #maximintegrated

This project is a Pulse Width Modulation (PWM) Controller, built around an LM555 timer IC. It controls a load connected to a MOSFET, with adjustments via a potentiometer, and uses capacitors, resistors and diodes for various functions. #PWM #controller #project #Template #projectTemplate

This is a STM32F4 Flight Controller template with 6-axis Accelerometer, Gyroscope. With OSD generator MAX7456EUI. #drone #flightController #STM32F405 #controller #OSD #video #referenceDesign #project #MPU6000 #template

This is a Servo Controller Robotic Platform template with 9-axis MEMS sensor(Accelerometer, Gyroscope, Magnetometer). Can control up to 16 servo motors. #robotics #motorController #PCA9685 #controller #motor #servo #referenceDesign #project #MPU-9250 #MPU9250 #template

This project is a Pulse Width Modulation (PWM) Controller, built around an LM555 timer IC. It controls a load connected to a MOSFET, with adjustments via a potentiometer, and uses capacitors, resistors and diodes for various functions. #PWM #controller #project #Template #projectTemplate

This is a STM32F4 Flight Controller template with 6-axis Accelerometer, Gyroscope. With OSD generator MAX7456EUI. #drone #flightController #STM32F405 #controller #OSD #video #referenceDesign #project #MPU6000 #template

This project is a Pulse Width Modulation (PWM) Controller, built around an LM555 timer IC. It controls a load connected to a MOSFET, with adjustments via a potentiometer, and uses capacitors, resistors and diodes for various functions. #PWM #controller #project #Template #projectTemplate

This project is a controller module that uses the ESP32-WROOM-32E and the MAX3485 to communicate with Modbus devices. It has a USB-C port for power and data, a voltage regulator for stable operation. It also has a CH340C chip for USB to serial conversion. #referenceDesign #project #ESP32 #ESP32WROOM #RF #WIFI #MCU #reusable #module #simple-embedded #espressif #template #MAX3485 #RS485 #maximintegrated

A smart ESP32-based battery management system controller board for Lithium ion battery packs/cells. Capable of communicating to wide varieties of hybrid-smart inverters with CANbus, RS485 and UART communication. Inspired by the open-source project diyBMS by Stuart Pittaway #smartHomeDevices #esp32 #iot

A smart ESP32-based battery management system controller board for Lithium ion battery packs/cells. Capable of communicating to wide varieties of hybrid-smart inverters with CANbus, RS485 and UART communication. Inspired by the open-source project diyBMS by Stuart Pittaway #smartHomeDevices #esp32 #iot

Test Project for auto layout: Flight Controller Notes - Auto layout works okay

This is a STM32F4 Flight Controller template with 6-axis Accelerometer, Gyroscope. With OSD generator MAX7456EUI. #drone #flightController #STM32F405 #controller #OSD #video #referenceDesign #project #MPU6000 #template

The electronic speed controller (ESC) is an essential part of an electric propulsion system’s hardware. It acts like the brain of the system by telling the motor how fast to go based on data signals it receives from the throttle controller. For smaller applications like drones and RC vehicles, this controller has the name ‘ESC’, whereas for larger manufacturing applications it may be called an electronic control unit, inverter, or motor controller. #drone #motorController #PCA9685 #controller #motor #esc #referenceDesign #project #EFM8BB21F16G #MPU9250 #template

This project is a Pulse Width Modulation (PWM) Controller, built around an LM555 timer IC. It controls a load connected to a MOSFET, with adjustments via a potentiometer, and uses capacitors, resistors and diodes for various functions. #PWM #controller #project #Template #projectTemplate

This is a VGA signal generation based on ICE40 Field-programmable gate array chip #VGA #FPGA #ICE40HX1K #ICE40 #controller #referenceDesign #project #template #SRAM #video #display

This project is a Pulse Width Modulation (PWM) Controller, built around an LM555 timer IC. It controls a load connected to a MOSFET, with adjustments via a potentiometer, and uses capacitors, resistors and diodes for various functions. #PWM #controller #project #Template #projectTemplate

This project is a Pulse Width Modulation (PWM) Controller, built around an LM555 timer IC. It controls a load connected to a MOSFET, with adjustments via a potentiometer, and uses capacitors, resistors and diodes for various functions. #PWM #controller #project #Template #projectTemplate

This project is a controller module that uses the ESP32-WROOM-32E and the MAX3485 to communicate with Modbus devices. It has a USB-C port for power and data, a voltage regulator for stable operation, and headers for connecting sensors and actuators. It also has a CH340C chip for USB to serial conversion. #referenceDesign #project #ESP32 #ESP32WROOM #RF #WIFI #MCU #referenceDesign #simple-embedded #espressif #template #MAX3485 #RS485 #maximintegrated #reference-design

This project is a controller module that uses the ESP32-WROOM-32E and the MAX3485 to communicate with Modbus devices. It has a USB-C port for power and data, a voltage regulator for stable operation, and headers for connecting sensors and actuators. It also has a CH340C chip for USB to serial conversion. #referenceDesign #project #ESP32 #ESP32WROOM #RF #WIFI #MCU #referenceDesign #simple-embedded #espressif #template #MAX3485 #RS485 #maximintegrated #reference-design

This project is a controller module that uses the ESP32-WROOM-32E and the MAX3485 to communicate with Modbus devices. It has a USB-C port for power and data, a voltage regulator for stable operation. It also has a CH340C chip for USB to serial conversion. #referenceDesign #project #ESP32 #ESP32WROOM #RF #WIFI #MCU #reusable #module #simple-embedded #espressif #template #MAX3485 #RS485 #maximintegrated

This is a Servo Controller Robotic Platform template with 9-axis MEMS sensor(Accelerometer, Gyroscope, Magnetometer). Can control up to 16 servo motors. #robotics #motorController #PCA9685 #controller #motor #servo #referenceDesign #project #MPU-9250 #MPU9250 #template

This is a Servo Controller Robotic Platform template with 9-axis MEMS sensor(Accelerometer, Gyroscope, Magnetometer). Can control up to 16 servo motors. #robotics #motorController #PCA9685 #controller #motor #servo #referenceDesign #project #MPU-9250 #MPU9250 #template