This is a 7-segment controller. It runs on a 3-bit counter so the count is from 0-7. Buttons to toggle reset, pause, increment. Knobs to control speed and lighting configuration. Try the simulation here: https://www.flux.ai/jbreidfjord-dev/7-seg-3-bit-counter

Shield for measuring voltage/current using three ACS712s. The shield is suitable for your IoT devices where power monitoring is required, such as a solar station

An I2C extension shield with 6 shielded ethernet ports and a TCA9548 breakout board. This board is for the target side, any microcontroller with a standard Arduino header can use it. With proper target side hardware and an SSTP ethernet cable, the board provides robust i2c communication over 10ft(could be longer, haven't tested it yet) with a bitrate of 400kHz under a noisy environment( near motors, power cables, switches, etc). The shield board provides power to the target side and can power the i2c device. The board also supports drdy trigger, which is available on many i2c sensors. The TCA9548 breakout board is for a scenario in which all of your i2c devices have the same address. #Arduino #Uno #Shield #Template #project-template #project

This project is a reference design for an ESP32-WROOM-32E based device. It features USB-C for power and data transfer, onboard voltage regulation, and multiple peripheral connections. It also includes a CH340C for USB to serial conversion #referenceDesign #project #ESP32 #ESP32WROOM #RF #WIFI #MCU #referenceDesign #simple-embedded #espressif #template #reference-design

Designing a Tractive System Active light(TSAL) circuit for an Electric Vehicle which does the following operations 1. The TSAL itself must have a red light, flashing continuously with a frequency between 2 Hz and 5 Hz and a duty cycle of 50%, active if and only if the LVS is active and the voltage across DC-link capacitors exceeds half the nominal TS voltage 2. The TSAL itself must have a green light, continuously on, active if and only if the LVS is active and ALL of the following conditions are true: ● All AIRs are opened. ● The pre-charge relay is opened. ● The voltage at the vehicle side of the AIRs inside the TSAC does not exceed 60 VDC or 50 VAC RMS. This schematic will include only the Green Light logic. We have to take proper care of High voltage and Low voltage isolation in this schematic because it will have to be implemented on the PCB as well.

This project is a reference project for ESP32-S3-MINI-1 to develop your IoT ideas. The board has RGB LEDs, USB C for firmware, EN and BOOT buttons, and 2 IO connectors for development #IoT #WiFi #MCU #RF #ESP32 #project #referenceDesign #simple-embedded #espressif #template #reference-design

This project is a reference project for ESP32-S3-WROOM-1 to develop your IoT ideas. The board has 3 LEDs, USB C for firmware, EN and BOOT buttons, and 2 IO connectors for development #IoT #WiFi #MCU #RF #ESP32 #project #referenceDesign #simple-embedded #espressif #template #reference-design

Template for Arduino Uno R3 Shield. Include an official pinout so you will always know Arduino names, the alternative roles of pins, which one is SDA, or SCL, etc. On PCB you can find the 3D model of the Arduino Uno R3 itself along with the board outline on the silkscreen. #Arduino #Uno #Shield #Template #project-template #project

Template for Arduino Uno R3 Shield. Include an official pinout so you will always know Arduino names, the alternative roles of pins, which one is SDA, or SCL, etc. On PCB you can find the 3D model of the Arduino Uno R3 itself along with the board outline on the silkscreen. #Arduino #Uno #Shield #Template #project-template #project

This is a motion detector circuit using an ESP32 microcontroller and PIR sensor. It features USB-C connectivity, RGB LED indication, push buttons and is powered by a 3.3V supply. #referenceDesign #edge-computing #edgeComputing #espressif #template #iot #PIR #esp32 #reference-design

Template for Arduino Uno R3 Shield. Include an official pinout so you will always know Arduino names, the alternative roles of pins, which one is SDA, or SCL, etc. On PCB you can find the 3D model of the Arduino Uno R3 itself along with the board outline on the silkscreen. #Arduino #Uno #Shield #Template #project-template #project

Modified by markwu2001: - Adjustable Brightness, - 85-90% Drive Efficiency - <5W Operation (Can use 5V 1A Plug) This project can be purchased from LCSC Original Description: Daddy's second circuit board. A sign to let my wife know when I'm on a call. Activates with a slide switch and is powered by USB-C.

This project is a WiFi RF-ID Lock, which uses a Espressif ESP-8684 microcontroller for WiFi connectivity and a Handson Technology RC522 for RF-ID functionality. It also includes an OLED display and user control via a switch. A step-up power converter ensures consistent 3.3V power. #WiFi #MCU #ReferenceDesign #project #ESP8684 #lock #OLED #referenceDesign #simple-embedded #espressif #template #reference-design

The Smart Hospital Bed is designed to enhance the care and comfort of patients with limited mobility by streamlining repositioning and maintaining detailed health records. It features automated repositioning options via an intuitive control interface, along with a rotating mechanism that allows the bed to transform into a chair for better comfort and adaptability. Additionally, its health data recording system provides real-time data base record on vital signs and posture, accessible remotely by healthcare providers helps them with decision making.

1. Overview: The Pundit pendant is a wearable AI transcription assistant. An innovative device designed to seamlessly integrate into daily activities, providing real-time transcription and note-taking capabilities. Combining advanced AI algorithms with state-of-the-art hardware components, the device offers crystal clear audio recording, durable construction, and convenient features such as cloud synchronization, weatherproofing, and a vibrant display for animations and expressions. 2. Hardware Specifications: * Rechargeable Battery: Lithium-ion battery providing up to 150 hours of continuous operation. * Construction: Durable aluminum body ensuring longevity and protection against wear and tear. * Audio Quality: High-fidelity microphone array for clear and accurate transcription, with noise cancellation technology. * Weatherproofing: Sealed construction to withstand various weather conditions, making it suitable for outdoor use. * Versatile Mounting: Equipped with a magnetic clasp for easy attachment to clothing or accessories. * Connectivity: Wi-Fi and Bluetooth connectivity for seamless data transfer and integration with other devices. * Charging: USB-C port for fast and convenient charging, with support for various power sources. * Input Microphone Array: Multiple microphones strategically placed for optimal audio capture and transcription accuracy. * Display: Colorful screen for displaying animations, expressions, and status indicators, enhancing user interaction and personalization. 3. Software Features: * Real-time Transcription: Utilizes AI algorithms for instant transcription of spoken words into text, with high accuracy. * Note-taking: Automatically creates and organizes notes based on conversations, timestamps, and contextual cues. * Audio Recording: One-touch button for initiating audio recording, with options for manual or automatic saving. * Cloud Synchronization: Syncs transcription data to the cloud for easy access and retrieval from any device. * Speech Recognition: Advanced speech recognition technology for identifying speakers and distinguishing between multiple voices. * Language Support: Multilingual support for transcription and note-taking in various languages. * Customization: User-configurable settings for adjusting transcription preferences, language models, and display animations. * Security: Encryption and authentication protocols to ensure the privacy and security of transcription data. 4. Dimensions and Weight: * Dimensions: Compact and lightweight design for comfortable wearability. * Weight: Minimal weight to prevent discomfort during prolonged use. 5. Compatibility: * Operating Systems: Compatible with iOS, Android, and other major operating systems. * Applications: Integration with popular productivity and communication apps for seamless workflow management. 6. Warranty and Support: * Warranty: Manufacturer's warranty covering defects in materials and workmanship. * Support: Dedicated customer support for technical assistance, troubleshooting, and software updates. 7. Target Market: * Professionals: Ideal for professionals in various industries, including journalists, researchers, students, and business professionals. * Outdoor Enthusiasts: Suitable for outdoor activities such as hiking, camping, and fieldwork where reliable transcription and note-taking are essential. * Everyday Users: Provides convenience and efficiency for everyday tasks, such as meetings, lectures, and personal reminders. 8. Conclusion: The Wearable AI Transcription Assistant sets a new standard for wearable technology, offering unmatched transcription and note-taking capabilities in a compact and durable package. With its advanced features, seamless connectivity, vibrant display, and user-friendly design, it is poised to revolutionize how we capture and manage information in our daily lives while adding a touch of personality and fun with customizable animations and expressions.

This project is a motherboard for the ESP32-CAM module, which enables easy and flexible WiFi camera applications. The motherboard provides power supply, programming interface, and GPIO expansion for the ESP32-CAM. It also supports external sensors for more functionality. #motherboard #WiFi #MCU #ReferenceDesign #project #ESP32 #camera #referenceDesign #edgeComputing #espressif #template #reference-design

This project involves designing a versatile IoT sensor hub using the ESP32-WROOM-32E module. The main objective is to create a platform that enables seamless data collection and transmission from various environmental sensors over a WiFi network. The device will feature USB-C for power and data transfer, and will utilize on-board voltage regulation to ensure stable operation. A CH340C chip is employed for USB to serial conversion, facilitating easy programming and communication with a host computer. Key Features: Wireless Connectivity: Leverage the ESP32's built-in WiFi capabilities for real-time data transmission to cloud-based platforms or local servers. USB-C Interface: Utilize a modern USB-C connector for power and data transfer, providing flexibility and future-proofing the design. On-board Voltage Regulation: Include an AMS1117-3.3 voltage regulator to maintain a stable 3.3V output from the USB input, protecting sensitive components. Support for Multiple Sensors: Integrate various GPIOs to connect multiple sensor types ( temperature, humidity, air quality ) (temperature, humidity, air quality) for comprehensive environmental monitoring. Expandability: Design with additional headers for future expansion, enabling users to customize and extend the hub's capabilities with additional sensors or modules. Applications: Smart Home Automation: Integrating with home systems to monitor and respond to environmental changes. Environmental Monitoring: Providing data for ecological studies or urban environment monitoring. Industrial IoT: Enhancing systems within a factory or industrial setting to track conditions in real-time. With this setup, the device aims to be a robust and adaptable piece of technology, suitable for hobbyists, researchers, and developers interested in the expanding world of IoT.

Rainbow is a pet collar project that would be programmed to send its location alerts whenever your pet is out of a predefined geofence. It also has a microphone and an accelerometer sensor to enable pet owners monitor their pets activities remotely #Pets #geofence #geolocation #collar #template

This project is a reference design for an ESP32-WROOM-32E based device. It features USB-C for power and data transfer, onboard voltage regulation, and multiple peripheral connections. It also includes a CH340C for USB to serial conversion #referenceDesign #project #ESP32 #ESP32WROOM #RF #WIFI #MCU #simpleEmbedded #espressif #template

This is a BLE remote control Reference Design. It features a Microchip RN4871U BLE module for communication, various push buttons (Up, Down, Left, Right, OK) for control input, and a piezoelectric buzzer for audio feedback. Power is supplied by a battery and it is regulated to 3.3V for the BLE module. #BLE #IoT #referenceDesign #simple-embedded #microchip #template #reference-design

The LoSS - ST LoRa Data Logger project is designed to collect and log data using LoRa connectivity. It includes interfaces for JTAG and UART communication. Key components include multiple capacitors, resistors, a crystal oscillator, and an NXP MCU. The device interacts with various sensors and transmits data periodically using LoRa technology. Interface elements include buttons and a display for user interaction.

This LTC3401-based reference design is a boost converter, transforming a lower input voltage into a stable 3V3 output. Perfect for applications that need a regulated 3V3 power source. #referenceDesign #project #boostConverter #voltageRegulator #3V3 #LTC3401 #referenceDesign #powermanagement #analogdevices #template #reference-design #polygon

This ADM3054BRWZ-RL7-based reference design is a CAN bus transceiver circuit, providing reliable data communication over the CAN network. The design features a range of capacitors and resistors to ensure signal integrity, and a NUP2105L for voltage protection. It's ideal for applications requiring reliable data communication in an automotive or industrial environment. #referenceDesign #project #CANbus #interface #transceiverCircuit #ADM3054 #ADM3054BRWZ-RL7 #referenceDesign #canbus #texas-instruments #template #reference-design #reference-design

This is a BLE remote control Reference Design. It features a Microchip RN4871U BLE module for communication, various push buttons (Up, Down, Left, Right, OK) for control input, and a piezoelectric buzzer for audio feedback. Power is supplied by a battery and it is regulated to 3.3V for the BLE module. #BLE #IoT #referenceDesign #simple-embedded #microchip #template #reference-design

A compact battery-powered door/window sensor built around the ESP32-C3-MINI-1-N4 module. The design uses a single non-rechargeable AA cell with a TPS613221A 3.3 V boost regulator, reed switch magnetic contact sensing, low-power wake/report/sleep firmware strategy, RGB status LED for setup feedback, BOOT/EN controls, programming header, and input polarity protection. It is intended for smart-home security and automation applications, supporting WiFi or Bluetooth LE hub reporting with emphasis on low idle current, reliable RF burst power delivery, and field-replaceable battery operation. #ESP32-C3 #BLE #WiFi #DoorSensor #WindowSensor #ReedSwitch #LowPower #BatteryPowered #SmartHome #IoT

This project is a plant care system that uses an ESP32-S3-MINI-1U-N8 microcontroller to automate plant care tasks. This system includes three Songle relays, multiple resistors, capacitors, and transistors, all powered at 3.3V, 5V, or 12V. It also incorporates a USB Type-C connector. #referenceDesign #edge-computing #edgeComputing #espressif #template #iot #ESP32 #relay #reference-design

Design a circuit that detects the presence of the infrared signal. The circuit should light a red LED when infrared signal is detected otherwise it should light a green LED. You may use NPN transistors, IR LED, Photodiode, Red LED, Green LED and a rectifier diode.

This project is a reference design for an ESP32-WROOM-32U based device. It features USB-C for power and data transfer, onboard voltage regulation, and multiple peripheral connections. It also includes a CH340C for USB to serial conversion #referenceDesign #project #ESP32 #ESP32WROOM #RF #WIFI #MCU #referenceDesign #simple-embedded #espressif #template #reference-design

Based on Avia Semiconductor’s patented technology, HX711 is a precision 24-bit analog-to-digital converter (ADC) designed for weigh scales and industrial control applications to interface directly with a bridge sensor.

The Open-Source Laptop Webcam Module is a critical component of our open-source laptop initiative. This module will provide high-definition video capture capabilities while adhering to the principles of open-source design. The module must integrate seamlessly with the laptop’s mainboard, ensuring compatibility, ease of assembly, and potential for future upgrades.

The Ariel AI Chip, a state-of-the-art integrated circuit designed for high-performance computing applications, incorporates an innovative architecture that leverages radical transistor technology to optimize AI and machine learning tasks. At the heart of this chip lies a quad-core CPU operating at a clock speed of 2GHz, distinguished by its part number CPU-RT-4C-2G. The chip's power management is efficiently handled by a DC power supply, specified as DCPS-5V, ensuring a stable 5V input. Key to its operation are two NPN transistors, identified by part numbers NPN-TRANS-001 and NPN-TRANS-002, which, along with a pair of 1kΩ resistors (RES-1K and RES-1K-002) and a 10µF capacitor (CAP-10UF), form the critical signal processing and conditioning circuitry. This assembly is designed for seamless integration into advanced computing systems, particularly those focused on Flux AI environments, where its performance and efficiency can be fully leveraged. The Ariel AI Chip sets a new benchmark in AI computing, offering unparalleled processing power and efficiency for cutting-edge applications.

Requirements: -Daytime Operation Only -Track Bee Input/Output Directionality -Connects to House via WiFi TODO: -Connect EN high or low on MPPT IC -Finish Routing -Check Fill Thing Features: -MPPT Solar Power Conditioning -96% efficient IR LED Drive Next Version Feature Wants: Microphone!

A 3-bit counter showcasing digital logic simulation. Input is a sequence of pulses which pass through a logic block to determine the segments.

This project is a DC-DC Buck converter based on the LM2596 IC. It is designed to step down the input voltage from 12V to a regulated output of 5V #Buck #LM2596 #project

This is a WiFi to Infrared (IR) gateway reference design leveraging an ESP32-S3 microcontroller for WiFi connectivity. It also incorporates a Type-C USB interface for data and power, 3 LEDs (red, green, & IR), and voltage regulation. It facilitates wireless control of IR devices, suitable for home automation projects. #referenceDesign #edge-computing #espressif #template #IR #project #reference-design

This project involves designing a PCB for the lid assembly of an open-source laptop. The design integrates various sensors, including a microphone, camera, and ambient light sensor, ensuring precise alignment with the display glass. It features touch sensors to control LED lighting, spring-loaded contacts for touch-key interaction, and 3D-printed light diffusers for efficient lighting. Additionally, the PCB includes a power management system with status LEDs and a PFC for connecting to the external laptop PCB. The goal is to create a versatile, upgradeable, and user-friendly component for the laptop's lid. Specific parts of the project include 1. Microphone - Audio input capture 2. Ambient Light Sensor Module - Light intensity measurement 3. Camera - Video capture 4. LDO Regulators (3 TLV74 Series) - Voltage regulation for different components 5. Crystal - Clock generation 6. Touch Sensor Controller - Touch-key interaction 7. Flip-Flop - State keeping in logic circuits 8. LEDs (LTRBR37G Series) - Lighting indication 9. FPC Connector - Interface with main laptop PCB

This project is a reference design for an ESP32-WROOM-32E based device. It features USB-C for power and data transfer, onboard voltage regulation, and multiple peripheral connections. It also includes a CH340C for USB to serial conversion #referenceDesign #project #ESP32 #ESP32WROOM #RF #WIFI #MCU #referenceDesign #simple-embedded #espressif #template #reference-design

This circuit is an ultrasonic distance meter based on an ATTiny2313 microcontroller. It uses an HC-SR04 ultrasonic sensor to measure distance and displays the results on an OLED display. The power supply is constructed using a Boost converter (TPS613222A) and a 2-cell AA battery. Additionally, it also includes ISP for programming, RESET and START switches, and LED indicators. #project #Template #projectTemplate #ultrasonic #OLED #arduino #attiny2313 #TPS613222A #ISP #referenceDesign #simple-embedded #microchip #template #reference-design .

Use this template to ensure your design is manufacturable.

The AD8495 K-type thermocouple amplifier from Analog Devices is so easy to use, we documented the whole thing on the back of the tiny PCB. Power the board with 3-18VDC and measure the output voltage on the OUT pin. You can easily convert the voltage to temperature with the following equation: Temperature = (Vout - 1.25) / 0.005 V. So for example, if the voltage is 1.5VDC, the temperature is (1.5 - 1.25) / 0.005 = 50°C with terminal block connections

This is a Kitchen Assistant Reference Design that runs on an ESP32 that connects to the network. The board has a microphone and bazer for communication and a display #referenceDesign #edge-computing #edgeComputing #espressif #template #esp32 #iot #i2s #reference-design

The Pico Macro Keyboard is a compact and powerful macro pad built using the latest Raspberry Pi Pico 2. Inspired by the Figma Creator Micro, this keyboard is designed for customizable control and enhanced productivity. It features mechanical switches with per-key RGB lighting, along with two rotary encoders for added functionality. With a modular 4-layer PCB and fully customizable keymaps, it seamlessly integrates with any software, making it perfect for designers, gamers, and power users alike.

This is the general design of the R7FA4M1AB3CFM with the minimum configuration for its operation and USB C with LDO and SD card #arm #M4 #IoT #referenceDesign #mcu #renesas #template #reference-design

This is a very simple timer circuit. When you push down to turn on the S1, this will turn on the LED and it also will charge the C1 Capacitor. Then upon releasing the push button switch, the LED will stay lit for couple of seconds until C1 is completely discharged.

R2 w Thread changes: -Moving to Letter Modules for ease of design -Adding MGM210L for Matter on Thread On/Off and intensity control -Shifted A and R letters closer to fix Kerning -Optional: Add unpopulated AA Battery Holder for battery option R1 changes: -Changed LED part to Red LEDs -adjusted resistor value of buck converter -Changed source for USB-C Connector -Removed exposed soldermask on buck converter with negative soldermask expansion -Order with black soldermask Modified by markwu2001: - Adjustable Brightness, - 85-90% Drive Efficiency - <5W Operation (Can use 5V 1A Plug) This project can be purchased from LCSC Original Description: Daddy's second circuit board. A sign to let my wife know when I'm on a call. Activates with a slide switch and is powered by USB-C. #template #arduino-matter

This is a common base little-known amplifier using a BJT. This type is used at high frequencies. #BJT #amplifier #commonBase

This project is a Pulse Width Modulation (PWM) Controller, built around an LM555 timer IC. It controls a load connected to a MOSFET, with adjustments via a potentiometer, and uses capacitors, resistors and diodes for various functions. #PWM #controller #project #Template #projectTemplate

This is the MGM240P template with minimal configuration for operation. There is a 3.3V regulator, a connector for UART and SWD #MGM240P #IoT #template #uart #3V3 #arduino-matter

hola tengo un viper22A dime como hacer un boost coverter con este ic quiero aumentar el voltage de una bateria de litio a 12v

The Arduino Uno learner's kit with ESP32 is a versatile educational tool for beginners. It combines an Arduino Uno board with additional components like a 2-channel motor driver, 7-segment display, relay outputs, programmable LEDs, push buttons, and analog inputs. This kit enables learners to explore electronics, programming, robotics, home automation, and more. With the ESP32 module, Wi-Fi and Bluetooth connectivity are possible, expanding the range of projects. It's a comprehensive package that fosters creativity and knowledge in the exciting world of electronics and programming. #arduino #esp32