This is a smart watch project based on E73-2G4M04S1A module with SoC nRF52810 on board. OLED display and coin battery #wearable #nRF52810 #E73 #Ebyte #BLE #referenceDesign

A simple voltage divider to showcase how to make parts. A voltage divider is a simple circuit which turns a large voltage into a smaller one. Using just two series resistors and an input voltage, we can create an output voltage that is a fraction of the input. Voltage dividers are one of the most fundamental circuits in electronics.

Welcome to your new project. Imagine what you can build here.

This is a BLE Controller project based on E73-2G4M04S1A module with SoC nRF52810 on board. Can be used to control RC cars, robots, planes, drones, etc #robotics #nRF52810 #E73 #Ebyte #BLE #referenceDesign

A simple voltage divider to showcase how to make parts. A voltage divider is a simple circuit which turns a large voltage into a smaller one. Using just two series resistors and an input voltage, we can create an output voltage that is a fraction of the input. Voltage dividers are one of the most fundamental circuits in electronics.

This project is a IoT templates for an RP2350A MCU from Raspberry Pi Pico 2 Development board #RaspberryPi #Raspberry #Pi #RPi #Pico2 #internetOfThings #referenceDesign #project #MCU #simpleEmbedded #polygon

Night Sky with constellation

cizgiizleyen.com

Change History from V1: -Font Bigger for SMD Footprint and IC designators -Confirmed that V1 worked for LED energy harvesting and NFC write/read Forked an amazing PCB business card from Mark Wu and added a SMD footprint and silkscreen art.

Use this Copilot's template to design audio applications like amplifiers, mixers, processors, etc. Modify project requirement properties to adapt to specific needs. #template #project-template

This project is a H-Bridge Circuit used to control the rotation direction of a DC motor. It uses resistors, diodes, and transistors to alternately forward and reverse the current flow. #HBridge #project #Template #projectTemplate

An I2C extension shield with 6 shielded ethernet ports and a TCA9548 breakout board. This board is for the target side, any microcontroller with a standard Arduino header can use it. With proper target side hardware and an SSTP ethernet cable, the board provides robust i2c communication over 10ft(could be longer, haven't tested it yet) with a bitrate of 400kHz under a noisy environment( near motors, power cables, switches, etc). The shield board provides power to the target side and can power the i2c device. The board also supports drdy trigger, which is available on many i2c sensors. The TCA9548 breakout board is for a scenario in which all of your i2c devices have the same address. #Arduino #Uno #Shield #Template #project-template #project

Vehicle Display System for Tesla Roadster #project #Template #projectTemplate

This project is a reference design for an ESP32-WROOM-32E based device. It features USB-C for power and data transfer, onboard voltage regulation, and multiple peripheral connections. It also includes a CH340C for USB to serial conversion #referenceDesign #project #ESP32 #ESP32WROOM #RF #WIFI #MCU #referenceDesign #simple-embedded #espressif #template #reference-design

This project is a reference project for ESP32-S3-MINI-1 to develop your IoT ideas. The board has RGB LEDs, USB C for firmware, EN and BOOT buttons, and 2 IO connectors for development #IoT #WiFi #MCU #RF #ESP32 #project #referenceDesign #simple-embedded #espressif #template #reference-design

This project is a reference project for ESP32-S3-WROOM-1 to develop your IoT ideas. The board has 3 LEDs, USB C for firmware, EN and BOOT buttons, and 2 IO connectors for development #IoT #WiFi #MCU #RF #ESP32 #project #referenceDesign #simple-embedded #espressif #template #reference-design

Template for Arduino Uno R3 Shield. Include an official pinout so you will always know Arduino names, the alternative roles of pins, which one is SDA, or SCL, etc. On PCB you can find the 3D model of the Arduino Uno R3 itself along with the board outline on the silkscreen. #Arduino #Uno #Shield #Template #project-template #project

This is a motion detector circuit using an ESP32 microcontroller and PIR sensor. It features USB-C connectivity, RGB LED indication, push buttons and is powered by a 3.3V supply. #referenceDesign #edge-computing #edgeComputing #espressif #template #iot #PIR #esp32 #reference-design

Template for Arduino Uno R3 Shield. Include an official pinout so you will always know Arduino names, the alternative roles of pins, which one is SDA, or SCL, etc. On PCB you can find the 3D model of the Arduino Uno R3 itself along with the board outline on the silkscreen. #Arduino #Uno #Shield #Template #project-template #project

This project is a WiFi RF-ID Lock, which uses a Espressif ESP-8684 microcontroller for WiFi connectivity and a Handson Technology RC522 for RF-ID functionality. It also includes an OLED display and user control via a switch. A step-up power converter ensures consistent 3.3V power. #WiFi #MCU #ReferenceDesign #project #ESP8684 #lock #OLED #referenceDesign #simple-embedded #espressif #template #reference-design

This project is a motherboard for the ESP32-CAM module, which enables easy and flexible WiFi camera applications. The motherboard provides power supply, programming interface, and GPIO expansion for the ESP32-CAM. It also supports external sensors for more functionality. #motherboard #WiFi #MCU #ReferenceDesign #project #ESP32 #camera #referenceDesign #edgeComputing #espressif #template #reference-design

Rainbow is a pet collar project that would be programmed to send its location alerts whenever your pet is out of a predefined geofence. It also has a microphone and an accelerometer sensor to enable pet owners monitor their pets activities remotely #Pets #geofence #geolocation #collar #template

This project is a reference design for an ESP32-WROOM-32E based device. It features USB-C for power and data transfer, onboard voltage regulation, and multiple peripheral connections. It also includes a CH340C for USB to serial conversion #referenceDesign #project #ESP32 #ESP32WROOM #RF #WIFI #MCU #simpleEmbedded #espressif #template

This is a BLE remote control Reference Design. It features a Microchip RN4871U BLE module for communication, various push buttons (Up, Down, Left, Right, OK) for control input, and a piezoelectric buzzer for audio feedback. Power is supplied by a battery and it is regulated to 3.3V for the BLE module. #BLE #IoT #referenceDesign #simple-embedded #microchip #template #reference-design

This project uses an ESP32 microcontroller and OV2640 camera to create a WiFi-enabled digital camera. It uses AMS1117 voltage regulators to provide regulated power, a CH340C for USB communication, and includes capacitors and resistors for circuit balance. Ideal for IoT and edge computing tasks. #referenceDesign #project #ESP32 #ESP32WROVER #RF #WIFI #MCU #referenceDesign #edge-computing #edgeComputing #espressif #template #reference-design