Quiero construir una tarjeta electronica basada en un arduino pro mini En el diagrama se debe indicar cómo cada sensor recibe alimentación (VCC y GND) y sus conexiones de datos (líneas I²C/SPI/UART). Por ejemplo, un proyecto de CanSat listó componentes como XBee, MPU-6050, MQ-135, BME180 (presión), Neo-6M (GPS) y Arduino Uno. Con base en esto, aseguren conectar cada módulo correctamente según su interfaz.

Etapa 1: Recolección y Almacenamiento de Energía Entrada: tus cactus en serie (ej. 15 cactus × 0.5 V = 7.5 V). Componente clave: Supercapacitor o batería recargable de baja capacidad (Li-ion o LiFePO4, 3.7V-7.4V). Diodo Schottky entre los cactus y el capacitor para evitar descarga inversa. 🛠 Ejemplo de componentes: Supercapacitor de 5–10 F, 5.5 V o batería de 3.7 V (tipo 18650). Diodo Schottky 1N5819. Módulo cargador TP4056 (si usas batería). Etapa 2: Aumento de Voltaje (Boost Converter) Conversión de 3.7 V / 7.5 V DC a 110 V AC. Necesitas: Boost Converter (DC-DC Step-up) de hasta 300 V DC. Inversor DC-AC (pequeño, tipo mini inverter para LEDs) que convierta ese voltaje a 110 V AC. NOTA: Algunos focos LED pueden funcionar con 110 V DC directamente, si quieres evitar el inversor. Etapa 3: Detección de Noche Sensor LDR (resistor dependiente de luz) conectado a un comparador (ej. LM393) o a un microcontrolador (como un ATtiny o ESP8266 si quieres funciones extra). Al bajar la luz solar: El comparador activa un MOSFET o un relé que conecta la energía almacenada al foco.

MEGA 2560 PRO MINI 5V (Embed) Development Board Embed CH340G / ATMEGA2560-16AU #promini #arduino #Mega #ATMEGA2560

Interface for Wemos D1 mini to sct-013 current sensor via a 3.5mm jack

This project uses an Arduino Mega microcontroller connected to 5 flexible sensors and a mini speaker with position and acceleration sensors to create an interactive device. It uses AMS1117 voltage regulators to provide regulated power, a CH340C for USB communication, and includes capacitors and resistors for circuit balance. Ideal for IoT and edge computing tasks. #referenceDesign #project #ArduinoMega #flexSensors #miniSpeaker #motionSensor #IoT #edgeComputing #reusable #module #Arduino #template

Wemos D1 Mini with single relay and rtc

GPS01-TD module is a quad-mode Mini GPS module that supports BDS/GPS/GLONASS/Galileo/QZSS/SBAS and fully supports BeiDou B3, which can provide users with high quality, strong anti-jamming and low-power positioning and navigation solutions.

sensory obstacle indicating device included with Arduino Mini board, HC-SR04 Ultrasonic sensor, Vibration Motor and a power supply

Here's a template for the popular ESP-8266EX microcontroller board, wemos D1 mini. A mini wifi board with 4MB flash based on ESP-8266EX #wemos #esp8266 #project-template #template

Welcome to your new project. Imagine what you can build here.

Welcome to your new project. Imagine what you can build here.

Welcome to your new project. Imagine what you can build here.

Welcome to your new project. Imagine what you can build here.

Welcome to your new project. Imagine what you can build here.

Welcome to your new project. Imagine what you can build here.

Welcome to your new project. Imagine what you can build here.

Welcome to your new project. Imagine what you can build here.

Welcome to your new project. Imagine what you can build here.

Welcome to your new project. Imagine what you can build here.

Welcome to your new project. Imagine what you can build here.

Welcome to your new project. Imagine what you can build here.

Welcome to your new project. Imagine what you can build here.

Welcome to your new project. Imagine what you can build here.

Welcome to your new project. Imagine what you can build here.

Welcome to your new project. Imagine what you can build here.