Welcome to your new project. Imagine what you can build here.

Welcome to your new project. Imagine what you can build here.

Welcome to your new project. Imagine what you can build here.

Welcome to your new project. Imagine what you can build here.

Designing a Tractive System Active light(TSAL) circuit for an Electric Vehicle which does the following operations 1. The TSAL itself must have a red light, flashing continuously with a frequency between 2 Hz and 5 Hz and a duty cycle of 50%, active if and only if the LVS is active and the voltage across DC-link capacitors exceeds half the nominal TS voltage 2. The TSAL itself must have a green light, continuously on, active if and only if the LVS is active and ALL of the following conditions are true: ● All AIRs are opened. ● The pre-charge relay is opened. ● The voltage at the vehicle side of the AIRs inside the TSAC does not exceed 60 VDC or 50 VAC RMS. This schematic will include only the Green Light logic. We have to take proper care of High voltage and Low voltage isolation in this schematic because it will have to be implemented on the PCB as well.

Design a circuit that detects the presence of the infrared signal. The circuit should light a red LED when infrared signal is detected otherwise it should light a green LED. You may use NPN transistors, IR LED, Photodiode, Red LED, Green LED and a rectifier diode.

This is a WiFi to Infrared (IR) gateway reference design leveraging an ESP32-S3 microcontroller for WiFi connectivity. It also incorporates a Type-C USB interface for data and power, 3 LEDs (red, green, & IR), and voltage regulation. It facilitates wireless control of IR devices, suitable for home automation projects. #referenceDesign #edge-computing #espressif #template #IR #project #reference-design

R2 w Thread changes: -Moving to Letter Modules for ease of design -Adding MGM210L for Matter on Thread On/Off and intensity control -Shifted A and R letters closer to fix Kerning -Optional: Add unpopulated AA Battery Holder for battery option R1 changes: -Changed LED part to Red LEDs -adjusted resistor value of buck converter -Changed source for USB-C Connector -Removed exposed soldermask on buck converter with negative soldermask expansion -Order with black soldermask Modified by markwu2001: - Adjustable Brightness, - 85-90% Drive Efficiency - <5W Operation (Can use 5V 1A Plug) This project can be purchased from LCSC Original Description: Daddy's second circuit board. A sign to let my wife know when I'm on a call. Activates with a slide switch and is powered by USB-C. #template #arduino-matter

quiero que de las siguientes instrucciones lo plasmes en un protoboard: Transformador: Convierte la tensión de CA de la red eléctrica (120 V) en una tensión de CA de menor voltaje (por ejemplo, 12 V). Puente rectificador: Convierte la tensión de CA de bajo voltaje en una tensión de CC pulsante. Filtro: Compuesto por condensadores y resistencias, elimina la ondulación de la tensión de CC pulsante y produce una tensión de CC más estable. Circuito regulador: Mantiene la tensión de CC a un nivel constante, incluso si la tensión de entrada o la carga varían. Este circuito puede ser un circuito integrado (CI) regulador de voltaje o un circuito discreto con transistores. Carga: Dispositivo que consume la energía eléctrica proporcionada por la fuente de alimentación, como una bombilla, un motor o un circuito electrónico. Conexiones: La entrada de CA se conecta al transformador. La salida de CA del transformador se conecta al puente rectificador. La salida de CC del puente rectificador se conecta al filtro. La salida de CC del filtro se conecta al circuito regulador. La salida de CC del circuito regulador se conecta a la carga.

R1 changes: -Changed LED part to Red LEDs -adjusted resistor value of buck converter -Changed source for USB-C Connector -Removed exposed soldermask on buck converter with negative soldermask expansion -Order with black soldermask Modified by markwu2001: - Adjustable Brightness, - 85-90% Drive Efficiency - <5W Operation (Can use 5V 1A Plug) This project can be purchased from LCSC Original Description: Daddy's second circuit board. A sign to let my wife know when I'm on a call. Activates with a slide switch and is powered by USB-C.

Welcome to your new project. Imagine what you can build here.

Welcome to your new project. Imagine what you can build here.

Welcome to your new project. Imagine what you can build here.

Welcome to your new project. Imagine what you can build here.

Welcome to your new project. Imagine what you can build here.

Welcome to your new project. Imagine what you can build here.

Welcome to your new project. Imagine what you can build here.

Arduino Electrical Control Shield -Redundant Temp. Sense -Geometric Monitoring -Dual RS232 Communication -USB Communication -Dual Motor Control -5 24V Control Relays -15 10V Analog IO -22 24V Protected IO

makes a circuit which has transistors, diodes, relays, IC Timer, LED, which first turns on a green LED lit from 0 to 35 degrees Celsius then turns off and turns on a yellow LED from 35 degrees Celsius to 50 degrees Celsius then turns off the yellow and turns on the red at 50 degrees or more which in turn will turn on an oscillator circuit with IC555 and a Buzzer. In addition it should turn on an exhaust fan at 110 VAC. Translated with DeepL.com (free version)