This is a project of an energy-efficient temperature and humidity sensor that works via Zigbee #Zigbee #sensor #iot #template #project

KTY81 series silicon temperature sensors

KTY81 series silicon temperature sensors

The AD8495 K-type thermocouple amplifier from Analog Devices is so easy to use, we documented the whole thing on the back of the tiny PCB. Power the board with 3-18VDC and measure the output voltage on the OUT pin. You can easily convert the voltage to temperature with the following equation: Temperature = (Vout - 1.25) / 0.005 V. So for example, if the voltage is 1.5VDC, the temperature is (1.5 - 1.25) / 0.005 = 50°C with terminal block connections

RP2040 is a low-cost, high-performance microcontroller device with flexible digital interfaces. Key features: • Dual Cortex M0+ processor cores, up to 133 MHz • 264 kB of embedded SRAM in 6 banks • 30 multifunction GPIO • 6 dedicated IO for SPI Flash (supporting XIP) • Dedicated hardware for commonly used peripherals • Programmable IO for extended peripheral support • 4 channel ADC with internal temperature sensor, 0.5 MSa/s, 12-bit conversion • USB 1.1 Host/Device

PT100 platinum temperature sensor (RTD) #commonpartslibrary #sensor #Temperaturesensor #integratedcircuit

Heating element temperature controller with 2S battery support and power meter.

The HOTCHIP HT4936S is a sophisticated mobile power management integrated circuit designed by Hotchip, optimized for portable power solutions that require efficient charging and power management capabilities. This advanced component integrates features for charging and discharging through a common port, automatic load detection for boost startup and shutdown, four-light battery level indication, and a low battery alert functionality. The HT4936S stands out for its ability to manage 1A input/output with minimal external components, leveraging synchronous rectification to enhance efficiency and reduce thermal footprint. Additionally, it supports a versatile charging protocol accommodating both 4.20V and 4.35V batteries, and is packaged in a compact SOP16 form factor, ensuring a low-cost, space-efficient solution for a wide range of mobile power applications including power banks, backup power supplies, and lithium battery chargers. It incorporates protection features against battery overcharge, over-discharge, and thermal overload, thereby ensuring reliable operation across a range of conditions. Furthermore, the HT4936S facilitates direct LED drive and includes an NTC thermistor input for temperature monitoring, making it an all-encompassing solution for power management in consumer electronics.

Build your own temperature sensor with RGB Thermometer. Monitor temperature with colorful hues. #DIYelectronics #Thermometer #RGBLED #Arduino

KTY81 series silicon temperature sensors

NTC Thermistor 0603 (1608 Metric) Template NO default properties #simplifiedFootprint #noProp #commonpartslibrary #ntc #thermistor #sensor #temperature #transducer

This is a board for energy-efficient projects, based on STM32 with a BQ25570 controller and a temperature humidity sensor. There is also a display and a supercapacitor in the role of power supply #MPPT #solar #STM32 #ti

Temperature Sensor Digital, Local -55°C ~ 125°C 9 b, 10 b, 11 b, 12 b TO-92 #commonpartslibrary #integratedcircuit #temperature #sensor #digital

Wi-Fi LED strip controller made with few goals: Dual voltage support 12V and 24V 2 independent channels for color temperature adjustments No high pitch noise in all modes Powerful enough to handle current up to 17.5A (in total, limited by connectors) Control buttons on the device body Connectors for external buttons Can be used with already installed LED strips Support of open source firmware, like https://esphome.io/

Wi-Fi LED strip controller made with few goals: Dual voltage support 12V and 24V 2 independent channels for color temperature adjustments No high pitch noise in all modes Powerful enough to handle current up to 17.5A (in total, limited by connectors) Control buttons on the device body Connectors for external buttons Can be used with already installed LED strips Support of open source firmware, like https://esphome.io/

This is a LoRa remote control project built around a Raspberry Pi RP2040 SoC and the RFM95W LoRa module. The design includes user interface features such as multiple buttons and LEDs, power management components, and a temperature sensor. The project utilizes SPI, I2C, and USB interfaces for communication and control. #referenceDesign #simple-embedded #raspberrypi #lora #template #reference-design

BME280 Humidity + Barometric Pressure + Temperature Sensor

The J175, J176, MMBFJ175, MMBFJ176, and MMBFJ177 are a series of P-Channel switches designed and manufactured by onsemi™, suitable for low-level analog switching, sample-and-hold circuits, and chopper-stabilized amplifiers. These components are sourced from process 88, indicating a specific manufacturing technique employed by onsemi™ to ensure consistent performance and reliability. The devices are offered in both TO-92 and SOT-23 packages, catering to a variety of mounting preferences and application requirements. They are characterized by their ability to handle a drain-gate voltage of -30V, a gate-source voltage of 30V, and a forward gate current of 50 mA. Operating and storage junction temperature ranges are specified from -55 to +150°C, ensuring robustness across a wide range of environmental conditions. With features like low on-resistance and high transconductance, these components are optimized for efficient signal modulation and minimal power loss, making them highly suitable for precision applications in analog signal processing.

This is a project for measuring the temperature using the SHT30 sensor and storing data on the SD card, using STM32F031K6Tx #stm32 #sht3x #sd

Humidity Temperature Sensor 0 ~ 100% RH I²C, SPI ±3% with 4 pins

A Fridge door Alarm is a simple PCB project designed to detect & inform the status of any refrigeration unit’s door: whether its open or not. It produces a monotonous beeping noise if the fridge door is left open for too long by an accident. It’s common use is in refrigerators, Temperature Controlled Freezers & beverage coolers.

The Pico-Environment-Sensor gives Raspberry Pi Pico the ability to collect environment data like temperature & humidity, air pressure, ambient light #RaspberryPi #Raspberry #Pi #RPi #Pico #template #project #project-template #hat

KTY81 series silicon temperature sensors

Texas Instruments presents the CD4051B, CD4052B, and CD4053B series, a family of CMOS single 8-Channel, differential 4-Channel, and triple 2-Channel analog multiplexers or demultiplexers with logic-level conversion. Engineered for precise, reliable control of analog and digital signals, these components are characterized by their wide range of signal handling (3 V to 20 V for digital and up to 20 VP-P for analog signals), low ON resistance (125 Ω typical over 15 VP-P signal input range for VDD - VEE = 18 V), high OFF resistance (+100 pA typical channel leakage at VDD - VEE = 18 V), and minimal quiescent power dissipation (0.2 μW typical at VDD - Vss = VDD - VEE = 10 V). They come equipped with on-chip binary address decoding for easy integration and minimized system logic complexity. Available in a variety of package types, including CDIP, PDIP, SOIC, SOP, and TSSOP, these multiplexers/demultiplexers support a broad spectrum of analog to digital and digital to analog conversion applications, signal gating, factory automation, and other uses where reliable signal handling is crucial. With parametric ratings at 5 V, 10 V, and 15 V, and an operational temperature range of -55°C to 125°C, these components are also 100% tested for quiescent current at 20 V, assuring dependable performance across diverse environmental conditions.

Heating element temperature controller with 2S battery support and power meter.

USB-C Powered ESP32-C3 + SHT45 Wi-Fi Temperature & Humidity Sensor Node

USB-C Powered ESP32-C3 + SHT45 Wi-Fi Temperature & Humidity Sensor Node

USB-C Powered ESP32-C3 + SHT45 Wi-Fi Temperature & Humidity Sensor Node

USB-C Powered ESP32-C3 + SHT45 Wi-Fi Temperature & Humidity Sensor Node

Low-Power USB-C Temperature & Humidity Sensor Node with Wi-Fi and BLE

USB-C Powered WiFi/BLE Indoor Humidity & Temperature Sensor Node

ESP32-Based Smart Wi-Fi/BLE Humidity & Temperature Sensor Board

I want to make the hardware and software for a 5.2 inch diameter capacitive touch screen display. Please give me all of the information the enable me to do this, I have NO experience of code or PCB design or manufacture. I want to measure a battery voltage and amps used via a coulomb counter to indicate a fuel level indicator icon I just want two connections + and - Its not single cell, its a battery of 20 cells LIFEPO4 each cell is 3.2v nominal and 100a I also want to include a can bus controller to read and display motor rpm And can bus temperature Also a GPS speedometer, odometer and trip. Toggle between knots, mph and kmh by touchscreen, Also toggle between nautical miles, km and miles with a Trip meter reset. Startup screen animation, Speed Incremental bar Plus a digital reading, And an animated compass heading STM32 or ESP32 Please recommend all hardware, I have the can protocol for the motor controller but not with me right now Connection via a 4 pin military connector can high can low +v and –v Top middle of screen incremental speed bar that fills 120 degrees with 60 degrees being top dead centre in an arc Dead middle of screen DIGITAL SPEED To the left of dead middle a Compass To the right of dead centre DIGITAL RPM Next line with a space between dead centre will be the ODOMETER, Trip and Battery level Below those are the Toggle buttons Heading compass by GPS, no WiFi or Bluetooth Write full GPS parsing code for my firmware Can you write the code with all of your recommendations for smoother bug free operation Can a FRAM replace the sd card ALL components must fit onto one board into an enclosure directly behind the screen that measures 5.0 inches diameter x 13mm deep inside dimensions

The Pico-Environment-Sensor gives Raspberry Pi Pico the ability to collect environment data like temperature & humidity, air pressure, ambient light #RaspberryPi #Raspberry #Pi #RPi #Pico #template #project #project-template #hat

The Pico-Environment-Sensor gives Raspberry Pi Pico the ability to collect environment data like temperature & humidity, air pressure, ambient light #RaspberryPi #Raspberry #Pi #RPi #Pico #template #project #project-template #hat

Product Type: Wearable AI pendant Primary Function: Records audio, generates transcripts, and organizes information about daily interactions User Interaction: Input: Activation button Output: RGB LED ring, Bluetooth link to phone Key Features: Audio Recording: Activated by button press Transcription: Converts audio to text Sentiment Analysis: Embedded AI evaluates sentiment Information Management: Filters essential information and action items Technical Specifications Form Factor: Wearable pendant Display: RGB LED ring around the edge Sensors: 2 Microphones 1 Button Connectivity: Bluetooth for phone linkage Wi-Fi USB-C for charging Wireless Protocol: Wi-Fi, Bluetooth Battery Type: LiPo 2000 mAh Battery Life: 6 hours of continuous use Charging Method: USB-C Operating Voltage: 3.3V Operating Conditions: Temperature Range: -10°C to 70°C Humidity: 10 to 90% Software: Python for AI and processing Compliance: RoHS, FCC, CE Reliability: 20,000 hrs Life Cycle Expectancy: 10 years AI Capabilities Speech to Text Recognition: Converts audio input to written text Embedded AI Sentiment Analysis: Evaluates the mood or sentiment expressed in the text Essential Information Filtering: Identifies and segregates crucial data and actionable items Power Consumption and Efficiency Power consumption must align with battery capacity to ensure 6 hours of continuous operational use.

A board with an array of LEDs that are controlled via STM32, and there is also an accelerometer and a temperature sensor! #stm32 #iot #magic #led

This is a project of an energy-efficient temperature and humidity sensor that works via Zigbee #Zigbee #sensor #iot #template #project

This is a project of an energy-efficient temperature and humidity sensor that works via Zigbee #Zigbee #sensor #iot #template #project

The Pico-Environment-Sensor gives Raspberry Pi Pico the ability to collect environment data like temperature & humidity, air pressure, ambient light #RaspberryPi #Raspberry #Pi #RPi #Pico #template #project #project-template #hat

Product Type: Wearable AI pendant Primary Function: Records audio, generates transcripts, and organizes information about daily interactions User Interaction: Input: Activation button Output: RGB LED ring, Bluetooth link to phone Key Features: Audio Recording: Activated by button press Transcription: Converts audio to text Sentiment Analysis: Embedded AI evaluates sentiment Information Management: Filters essential information and action items Technical Specifications Form Factor: Wearable pendant Display: RGB LED ring around the edge Sensors: 2 Microphones 1 Button Connectivity: Bluetooth for phone linkage Wi-Fi USB-C for charging Wireless Protocol: Wi-Fi, Bluetooth Battery Type: LiPo 2000 mAh Battery Life: 6 hours of continuous use Charging Method: USB-C Operating Voltage: 3.3V Operating Conditions: Temperature Range: -10°C to 70°C Humidity: 10 to 90% Software: Python for AI and processing Compliance: RoHS, FCC, CE Reliability: 20,000 hrs Life Cycle Expectancy: 10 years AI Capabilities Speech to Text Recognition: Converts audio input to written text Embedded AI Sentiment Analysis: Evaluates the mood or sentiment expressed in the text Essential Information Filtering: Identifies and segregates crucial data and actionable items Power Consumption and Efficiency Power consumption must align with battery capacity to ensure 6 hours of continuous operational use.

Product Type: Wearable AI pendant Primary Function: Records audio, generates transcripts, and organizes information about daily interactions User Interaction: Input: Activation button Output: RGB LED ring, Bluetooth link to phone Key Features: Audio Recording: Activated by button press Transcription: Converts audio to text Sentiment Analysis: Embedded AI evaluates sentiment Information Management: Filters essential information and action items Technical Specifications Form Factor: Wearable pendant Display: RGB LED ring around the edge Sensors: 2 Microphones 1 Button Connectivity: Bluetooth for phone linkage Wi-Fi USB-C for charging Wireless Protocol: Wi-Fi, Bluetooth Battery Type: LiPo 2000 mAh Battery Life: 6 hours of continuous use Charging Method: USB-C Operating Voltage: 3.3V Operating Conditions: Temperature Range: -10°C to 70°C Humidity: 10 to 90% Software: Python for AI and processing Compliance: RoHS, FCC, CE Reliability: 20,000 hrs Life Cycle Expectancy: 10 years AI Capabilities Speech to Text Recognition: Converts audio input to written text Embedded AI Sentiment Analysis: Evaluates the mood or sentiment expressed in the text Essential Information Filtering: Identifies and segregates crucial data and actionable items Power Consumption and Efficiency Power consumption must align with battery capacity to ensure 6 hours of continuous operational use.

A temperature & humidity shield based on Arduino Nano 33. A nice shield for your IoT projects! #Arduino #IoT #Shield #template #project #shield #bme

Weather Station controlled by STM32F031F6P6 MCU. 2x humidity and temperature sensors. USB powered

Temperature sensor based on the ESP32-C3-WROOM-02 module.

The Pico-Environment-Sensor gives Raspberry Pi Pico the ability to collect environment data like temperature & humidity, air pressure, ambient light #RaspberryPi #Raspberry #Pi #RPi #Pico #template #project #project-template #hat

Greenhouse controller with temperature and humidity control Input voltage 12v led voltage: 12v humidifier voltage: 5V Display: i2c 0.96 OLED display sensor: htu21d i2c

Temperature Sensor Digital, Local -55°C ~ 125°C 9 b, 10 b, 11 b, 12 b TO-92 #commonpartslibrary #integratedcircuit #temperature #sensor #digital

This is a LoRa remote control project built around a Raspberry Pi RP2040 SoC and the RFM95W LoRa module. The design includes user interface features such as multiple buttons and LEDs, power management components, and a temperature sensor. The project utilizes SPI, I2C, and USB interfaces for communication and control. #referenceDesign #simple-embedded #raspberrypi #lora #template #reference-design

The Samsung Electro-Mechanics Polymer Tantalum Capacitor, part number TCPBL18336MTBA0055, is a RoHS and Halogen Compliant electronic component designed for high reliability and performance in various electronic applications. This capacitor features a nominal capacitance of 33uF with a tolerance of ±20%, operating at a rated voltage of 18V. It showcases an ESR (Equivalent Series Resistance) maximum value of 55mΩ, demonstrating its efficiency in handling higher currents with minimal power loss. The part is encapsulated in a 3528 package, measuring 3.5mm in length, 2.8mm in width, and with a height of approximately 1.2mm, making it suitable for compact designs. The capacitor is capable of withstanding surge voltages up to 23.4V and is categorized under the MSL (Moisture Sensitivity Level) 3, indicating its resilience to moisture during soldering processes. Furthermore, it exhibits remarkable performance across a broad temperature range of -55°C to +105°C, ensuring stable operation under diverse environmental conditions. Key reliability tests, including shear, bending, solderability, resistance to soldering heat, vibration, and moisture resistance, confirm the component's durability and longevity, making it an ideal choice for high-reliability applications.