This project is a BLE door and window sensor design that uses a U-blox BMD-330-A-R for BLE communication, a reed switch as a sensor, a multi-color LED for status display, and is powered by VBAT. There's also a programming interface and reset switch included. #WiFi #BLE #MCU #ReferenceDesign #project #referenceDesign #simple-embedded #ublox #template #reference-design

Reference schematic for BM1387 hash chip. ASIC Bitmain Antminer S9 includes 63 BM1387 chips connected in chain according to this diagram Total Hash Rate: 13.5 TH/s SHA-256

A simulated blinking LED circuit using an astable multivibrator a.k.a "flip-flop" as a square wave generator. It also includes PCB layout of the project.

This project is a reference design for an ESP32-WROVER-E based device. It features USB-C for power and data transfer, onboard voltage regulation, and multiple peripheral connections. It also includes a CH340C for USB to serial conversion #referenceDesign #project #ESP32 #ESP32WROVER #RF #WIFI #MCU #referenceDesign #simple-embedded #espressif #template #reference-design

This project is a reference design for an ESP32-WROOM-32E based device. It features USB-C for power and data transfer, onboard voltage regulation, and multiple peripheral connections. It also includes a CH340C for USB to serial conversion #referenceDesign #project #ESP32 #ESP32WROOM #RF #WIFI #MCU #simpleEmbedded #espressif #template

This project is a reference design utilizing Texas Instruments' PGA300ARHHR, a precision analog and digital IC, for signal processing. The circuit also includes a Diodes Incorporated's FZT603QTA Transistor, passive components like resistors and capacitors, and connectors from JST Sales America Inc. #project #referenceDesign #industrialsensing #texas-instruments #template #reference-design

This project is a WiFi Camera with Motion Detection, utilizing ESP32-CAM module and HC-SR501 PIR sensor. The camera is activated by the sensor's output. The system also includes power regulation and communication headers for setup and control. #WiFi #MCU #PIR #ReferenceDesign #project #ESP32 #camera #referenceDesign #edgeComputing #espressif #template #reference-design

This project is a reference design for an ESP32-WROOM-32E based device. It features USB-C for power and data transfer, onboard voltage regulation, and multiple peripheral connections. It also includes a CH340C for USB to serial conversion #referenceDesign #project #ESP32 #ESP32WROOM #RF #WIFI #MCU #simpleEmbedded #espressif #template

This project is a reference design for an ESP32-WROOM-32E based device. It features USB-C for power and data transfer, onboard voltage regulation, and multiple peripheral connections. It also includes a CH340C for USB to serial conversion #referenceDesign #project #ESP32 #ESP32WROOM #RF #WIFI #MCU #simpleEmbedded #espressif #template

FLORA has a small but easy to use onboard reset button to reboot the system. The power supply is designed to be flexible and easy to use. There is an onboard polarized 2 JST battery connector with protection schottky diode for use with external battery packs from 3.5v to 16v DC in. Can be used with LiIon/LiPoly, LiFe, alkaline or rechargeable NiMh/NiCad batteries of any size. The FLORA does not have a LiPo charger included by design, this allows safe use with multiple battery types and reduces risk of fire as it is not recommended to charge these batteries on fabric.

This project is a WiFi RF-ID Lock, which uses a Espressif ESP-8684 microcontroller for WiFi connectivity and a Handson Technology RC522 for RF-ID functionality. It also includes an OLED display and user control via a switch. A step-up power converter ensures consistent 3.3V power. #WiFi #MCU #ReferenceDesign #project #ESP8684 #lock #OLED #referenceDesign #simple-embedded #espressif #template #reference-design

A simulated blinking LED circuit using an astable multivibrator a.k.a "flip-flop" as a square wave generator. It also includes PCB layout of the project.

Guitar pedal starter template based on project by Mark Wu. Includes schematic and PCB layout for basic DIY pedal hardware. This includes two 1/4" jacks (one for input and one for output), a 9V power supply (including LED), a 3PDT true bypass wiring setup, and an example potentiometer that can be copy/pasted throughout the circuit. The headers are meant to be unpopulated so that wires can be soldered to the pads. PCB design rules imported from the JLCPCB 2-layer stackup template. #template

A simulated blinking LED circuit using an astable multivibrator a.k.a "flip-flop" as a square wave generator. It also includes PCB layout of the project.

This project is a reference design for an ESP32-WROOM-32E based device. It features USB-C for power and data transfer, onboard voltage regulation, and multiple peripheral connections. It also includes a CH340C for USB to serial conversion #referenceDesign #project #ESP32 #ESP32WROOM #RF #WIFI #MCU #referenceDesign #simple-embedded #espressif #template #reference-design

This circuit is an ultrasonic distance meter based on an ATTiny2313 microcontroller. It uses an HC-SR04 ultrasonic sensor to measure distance and displays the results on an OLED display. The power supply is constructed using a Boost converter (TPS613222A) and a 2-cell AA battery. Additionally, it also includes ISP for programming, RESET and START switches, and LED indicators. #project #Template #projectTemplate #ultrasonic #OLED #arduino #attiny2313 #TPS613222A #ISP #referenceDesign #simple-embedded #microchip #template #reference-design

This project is a plant care system that uses an ESP32-S3-MINI-1U-N8 microcontroller to automate plant care tasks. This system includes three Songle relays, multiple resistors, capacitors, and transistors, all powered at 3.3V, 5V, or 12V. It also incorporates a USB Type-C connector. #referenceDesign #edge-computing #edgeComputing #espressif #template #iot #ESP32 #relay #reference-design

This project is a WiFi RF-ID Lock, which uses a Espressif ESP-8684 microcontroller for WiFi connectivity and a Handson Technology RC522 for RF-ID functionality. It also includes an OLED display and user control via a switch. A step-up power converter ensures consistent 3.3V power. #WiFi #MCU #ReferenceDesign #project #ESP8684 #lock #OLED #referenceDesign #simple-embedded #espressif #template #reference-design

This project is a distance detecting sensor circuit build around GP2Y0D805Z0F IC from SHARP/Socle Technology. It includes decoupling capacitors, feedback resistors, and a LED for signal indication, with power being supplied via the J1 connector. #referenceDesign #industrialsensing #sharp #template #reference-design

I2C to dual PWM controller. The LED-Warrior18, manufactured by Code Mercenaries, is an I2C to dual channel PWM LED driver specifically designed to provide seamless brightness control for LED applications. This component, available in SOIC8 package (LW18-S) and as a ready-to-use module (LW18-01MOD), offers dual 16-bit PWM outputs with a dimming range from 0.001% to 100% and operates at a PWM frequency of 730 Hz. It supports programmable period lengths for higher-frequency or lower-resolution operation and includes an 8-bit data to logarithmic mapping feature for smoother dimming operations with just 256 steps. The LED-Warrior18 is engineered for minimal external circuitry with a 5V power supply requirement, offering ease of use in various lighting applications. It also features a sync mode for synchronized control of multiple units and customizable power-on status settings, making it highly versatile for standalone operations or integrated systems. Additionally, custom variants of both the chip and module are available, catering to specific application needs. The module version, LW18-01MOD, simplifies integration by including terminal blocks and supporting up to 4A load sink current for each output. The LED-Warrior18 stands out for its straightforward interface and operational flexibility, providing a comprehensive solution for advanced LED dimming and control projects.

A simulated blinking LED circuit using an astable multivibrator a.k.a "flip-flop" as a square wave generator. It also includes PCB layout of the project.

This project is a reference design for an ESP32-WROOM-32UE based device. It features USB-C for power and data transfer, onboard voltage regulation, and multiple peripheral connections. It also includes a CH340C for USB to serial conversion #referenceDesign #project #ESP32 #ESP32WROOM #RF #WIFI #MCU #referenceDesign #simple-embedded #espressif #template #reference-design

Guitar pedal starter template based on project by Mark Wu. Includes schematic and PCB layout for basic DIY pedal hardware. This includes two 1/4" jacks (one for input and one for output), a 9V power supply (including LED), a 3PDT true bypass wiring setup, and an example potentiometer that can be copy/pasted throughout the circuit. The headers are meant to be unpopulated so that wires can be soldered to the pads. PCB design rules imported from the JLCPCB 2-layer stackup template. #template

This project is a distance detecting sensor circuit build around GP2Y0D805Z0F IC from SHARP/Socle Technology. It includes decoupling capacitors, feedback resistors, and a LED for signal indication, with power being supplied via the J1 connector. #referenceDesign #industrialsensing #sharp #template #reference-design

This is a recreation of the [EV5920-5048-V-00A](https://www.monolithicpower.com/en/ev5920-5048-v-00a.html) from MPS which demonstrates a MP5920 Hot-Swap controller commanding 5 MP5048 e-fuses in parallel. WIP Items: -Routing In flux, this project demonstrates hierarchal design through the use of modules. Additionally, parametric symbols are used extensively to improve schematic cleanliness. Components in the canvas are locked because their positions correspond to the same positions as the original layout. Changelog from Original MPS Design: - Not including GPIO2 or GPIO3 as included in the original board due to NC pin name on the IC. - PC1 and PC2 footprints are 5mm in pitch and 12.5mm in diameter rather than the 16mm diameter in the original layout. This change corresponds with the selected part more accurately. -Renamed Designators to be More Verbose

This project is a reference design for an ESP32-WROOM-32E based device. It features USB-C for power and data transfer, onboard voltage regulation, and multiple peripheral connections. It also includes a CH340C for USB to serial conversion #referenceDesign #project #ESP32 #ESP32WROOM #RF #WIFI #MCU #referenceDesign #simple-embedded #espressif #template #reference-design

Smart Thermostat design using an ESP32 module for WiFi connectivity and a BME680 sensor for environmental monitoring. The user interface includes an E-ink display and an encoder for settings adjustment. Power: USB and Battery Movement sensor

This project is a reference design for an ESP32-WROOM-32E based device. It features USB-C for power and data transfer, onboard voltage regulation, and multiple peripheral connections. It also includes a CH340C for USB to serial conversion #referenceDesign #project #ESP32 #ESP32WROOM #RF #WIFI #MCU #referenceDesign #simple-embedded #espressif #template #reference-design

A simulated blinking LED circuit using an astable multivibrator a.k.a "flip-flop" as a square wave generator. It also includes PCB layout of the project.

This is a recreation of the [EV5920-5048-V-00A](https://www.monolithicpower.com/en/ev5920-5048-v-00a.html) from MPS which demonstrates a MP5920 Hot-Swap controller commanding 5 MP5048 e-fuses in parallel. In Flux, this project demonstrates hierarchical design through the use of modules. Additionally, parametric symbols are used extensively to improve schematic cleanliness. Components in the canvas are locked because their positions correspond to the same positions as the original layout. Changelog from Original MPS Design: - Not including GPIO2 or GPIO3 as included in the original board due to NC pin name on the IC. - PC1 and PC2 footprints are 5mm in pitch and 12.5mm in diameter rather than the 16mm diameter in the original layout. This change corresponds with the selected part more accurately. -Renamed Designators to be More Verbose

A simulated blinking LED circuit using an astable multivibrator a.k.a "flip-flop" as a square wave generator. It also includes PCB layout of the project.

A simulated blinking LED circuit using an astable multivibrator a.k.a "flip-flop" as a square wave generator. It also includes PCB layout of the project.

A simulated blinking LED circuit using an astable multivibrator a.k.a "flip-flop" as a square wave generator. It also includes PCB layout of the project.

A simulated blinking LED circuit using an astable multivibrator a.k.a "flip-flop" as a square wave generator. It also includes PCB layout of the project.

A simulated blinking LED circuit using an astable multivibrator a.k.a "flip-flop" as a square wave generator. It also includes PCB layout of the project.

Guitar pedal starter template based on project by Mark Wu. Includes schematic and PCB layout for basic DIY pedal hardware. This includes two 1/4" jacks (one for input and one for output), a 9V power supply, a 3PDT true bypass wiring setup, and an example potentiometer that can be copy/pasted throughout the circuit. size is a good default size for a 125B enclosure. The headers are meant to be unpopulated so that wires can be soldered to the pads. PCB design rules imported from the JLCPCB 2-layer stackup template. Meant to be used with the 3PDT Breakout Board on my profile. #template

A simulated blinking LED circuit using an astable multivibrator a.k.a "flip-flop" as a square wave generator. It also includes PCB layout of the project.

A simulated blinking LED circuit using an astable multivibrator a.k.a "flip-flop" as a square wave generator. It also includes PCB layout of the project.

Template for Arduino Uno R3 Shield. Include an official pinout so you will always know Arduino names, the alternative roles of pins, which one is SDA, or SCL, etc. On PCB you can find the 3D model of the Arduino Uno R3 itself along with the board outline on the silkscreen. #Arduino #Uno #Shield #Template #project-template #project

Template for Arduino Uno R3 Shield. Include an official pinout so you will always know Arduino names, the alternative roles of pins, which one is SDA, or SCL, etc. On PCB you can find the 3D model of the Arduino Uno R3 itself along with the board outline on the silkscreen. #Arduino #Uno #Shield #Template #project-template #project

Template for Arduino Uno R3 Shield. Include an official pinout so you will always know Arduino names, the alternative roles of pins, which one is SDA, or SCL, etc. On PCB you can find the 3D model of the Arduino Uno R3 itself along with the board outline on the silkscreen. #Arduino #Uno #Shield #Template #project-template #project

Template for Arduino Uno R3 Shield. Include an official pinout so you will always know Arduino names, the alternative roles of pins, which one is SDA, or SCL, etc. On PCB you can find the 3D model of the Arduino Uno R3 itself along with the board outline on the silkscreen. #Arduino #Uno #Shield #Template #project-template #project

Template for Raspberry Pi 4 Shield. Include an official pinout so you will always know Raspberry Pi names, the alternative roles of pins, which one is SDA, or SCL, etc. On PCB you can find the 3D model of the Raspberry Pi itself along with the board outline on the silkscreen. #RaspberryPi #Raspberry #Pi #RPi #Shield #template #project #project-template #raspberry

Template for Arduino Uno R3 Shield. Include an official pinout so you will always know Arduino names, the alternative roles of pins, which one is SDA, or SCL, etc. On PCB you can find the 3D model of the Arduino Uno R3 itself along with the board outline on the silkscreen. #Arduino #Uno #Shield #Template #project-template #project

Template for Arduino Uno R3 Shield. Include an official pinout so you will always know Arduino names, the alternative roles of pins, which one is SDA, or SCL, etc. On PCB you can find the 3D model of the Arduino Uno R3 itself along with the board outline on the silkscreen. #Arduino #Uno #Shield #Template #project-template #project

Template for Arduino Uno R3 Shield. Include an official pinout so you will always know Arduino names, the alternative roles of pins, which one is SDA, or SCL, etc. On PCB you can find the 3D model of the Arduino Uno R3 itself along with the board outline on the silkscreen. #Arduino #Uno #Shield #Template #project-template #project

Template for Arduino Uno R3 Shield. Include an official pinout so you will always know Arduino names, the alternative roles of pins, which one is SDA, or SCL, etc. On PCB you can find the 3D model of the Arduino Uno R3 itself along with the board outline on the silkscreen. #Arduino #Uno #Shield #Template #project-template #project

Template for Arduino Uno R3 Shield. Include an official pinout so you will always know Arduino names, the alternative roles of pins, which one is SDA, or SCL, etc. On PCB you can find the 3D model of the Arduino Uno R3 itself along with the board outline on the silkscreen. #Arduino #Uno #Shield #Template #project-template #project

The LTC3109 from Linear Technology is a highly integrated DC/DC converter specifically designed for energy harvesting applications. It can operate from ultra-low input voltages as low as 30mV, utilizing a unique, proprietary auto-polarity architecture to function regardless of input polarity. The component is ideal for harvesting energy from thermoelectric generators (TEGs) and thermopiles, efficiently converting this energy to power remote sensors, wireless transmitters, and low-power devices. Key features include selectable output voltages of 2.35V, 3.3V, 4.1V, or 5V, a 2.2V low-dropout (LDO) regulator, a logic-controlled output, and an energy storage system to maintain operation during power interruptions. The LTC3109 is encapsulated in a small, 20-lead (4mm × 4mm) QFN or SSOP package, making it compact and suitable for space-constrained applications in HVAC systems, building automation, and industrial wireless sensing. Additionally, the power good indicator and the ability to use compact step-up transformers further enhance its suitability for low power, energy-harvesting systems.