High-level modular schematic requirements for a Teensy 4.1 based RFID-triggered audio system with Bluetooth input, analog source selection, stereo amplification, and 12V to 5V power partitioning.

50-W Stereo Analog Input Class-D Audio Amplifier with a small number of external components mounted on a circuit board that can be used to directly drive a speaker with an external analog audio source as the input; can also be configured as a 100-W, Class-D mono audio amplifier in PBTL mode.

Hybrid EEG BCI for Pluto X v1.1 using ESP32-WROOM-32 and ADS1299-6PAG with LiPo charging, 5V boost, -5V analog rail, split 3.3V analog/digital regulators, six EEG channels, RC electrode protection, and 80x60mm mixed-signal PCB constraints.

Automotive smart fuel pump controller with >12 V battery qualification, protected battery input, analog FSCM command following, 25 A current sensing, thermal/fault indication, blue/red LED signaling, and 5-second buzzer alert. Control and fault nets are explicitly terminated to avoid floating or undriven states; any intentionally provisional control nodes are weakly biased to safe defaults during refinement.

50-W Stereo Analog Input Class-D Audio Amplifier with a small number of external components mounted on a circuit board that can be used to directly drive a speaker with an external analog audio source as the input; can also be configured as a 100-W, Class-D mono audio amplifier in PBTL mode.

FlowState Headband EVT1 — 4-Channel EEG Calibration Device Closed-loop EEG neurofeedback headband for theta/beta baseline calibration. 4-layer mixed-signal PCB, 40x30mm. Core ICs: - ADS1299-4PAG (TI) — 4-channel 24-bit EEG analog front end, SPI interface, 250 SPS - nRF5340 (Nordic) — Dual-core BLE 5.3 SoC, 128 MHz app core + 64 MHz network core Key requirements: - Separate analog and digital power domains (dual LDO: LP5907 for AVDD, AP2112 for DVDD) - Split analog/digital ground planes with single-point connection - 6 electrode inputs (4 active + 1 reference + 1 DRL) with individual TVS ESD protection on each - LIS2DH12 accelerometer (I2C) for motion artifact detection - MCP73831 USB-C battery charging (300-500 mAh LiPo) - 2.4 GHz chip antenna or PCB trace antenna at board edge with 10mm keepout - Conformal coating for sweat/moisture protection Reference designs: - Analog front-end: TI ADS1299 EVM (SBAS499) - Digital/BLE: Nordic nRF5340 DK reference schematic Critical constraint: Microvolt-level EEG signals — analog input routing and power supply filtering are the highest-priority layout concerns.

Driver drowsiness detection ECG front end based on the AD8232 with ECG electrode interface, analog signal conditioning, a dedicated 50 Hz twin-T notch filter for power-line interference rejection, regulated low-noise analog power, and a downstream conditioned ECG output prepared for processing and fatigue/drowsiness analysis.

Simple bus-powered USB audio interface for MacBook Air and Ableton Live using a USB audio codec, stereo analog input and output path, monitoring buffer stages, USB-C power and data connectivity, and low-noise PCB guidance.

Misty Pink Replicator schematic finalized for layout handoff with ESP32-S3, USB-C battery charging, T5838 always-on wake microphone, CI1302 backup ASR analog microphone front end, HTEW0154T8 SPI e-ink display, standardized power/test nets, and final ERC-clean baseline.

50-W Stereo Analog Input Class-D Audio Amplifier with a small number of external components mounted on a circuit board that can be used to directly drive a speaker with an external analog audio source as the input; can also be configured as a 100-W, Class-D mono audio amplifier in PBTL mode.

Single-project implementation of the Blue Ant AMP Architecture Rev2 using one shared schematic with six logical board partitions: PCB-01 phono stage, PCB-02 input selector and relay attenuator interface, PCB-03 balanced driver and RCA-to-balanced conversion interface, PCB-04 dual logical power amplifier channels, PCB-05 multi-rail power supply, and PCB-06 isolated control and display. Explicit inter-partition connector interfaces and named nets preserve balanced signal handling after RCA conversion, distinct rail domains (+63V, -63V, +15V, -15V, +5V, +3.3V), and documented hard constraints including low-noise analog isolation and high-voltage domain separation.

CNC hydraulic press brake controller with STM32H743, ADS1256, 5x DAC8501 ±10V outputs, 3x AD598 LVDT interfaces, isolated 24V digital inputs, 100BASE-TX Ethernet, watchdog, E-stop hardware disable, and 4-layer 220mm x 160mm PCB architecture. Domains: field 24V I/O, precision analog, logic/Ethernet. Safety behavior: E-stop and valve-disable force all analog command outputs to 0V-safe state and disable field enables; watchdog and power-good supervisor reset MCU on comms or rail faults. PCB constraints: L1/L4 signal+components, L2 solid GND, L3 power plane, 1.0mm board inset margin, RJ45 at edge, field connectors on opposite edge, isolation corridor between field wiring and logic/Ethernet, 4x M4 plated mounting holes inset 10mm from corners.

Ultra-Compact 2-Layer PCB Redesign with Preserved Stackup and Net Classes (SPI / Analog / Power)

Smart Intercom Adapter for Analog Door Intercom using ESP32

Two-PCB low-noise EEG system: Digital board (ESP32-S3-MINI-1U + ADS1299 + CP2102N + USB-C + 1S Li-ion charger/power-path + DF40 mezzanine) and Analog board (3x ADS1299 + REF/BIAS/DRL + driven-shield electrode interfaces + local low-noise regulation + test points). DF40 mezzanine carries only power + digital SPI/control with shared SPI, shared START/RESET, and separate CS/DRDY per AFE. 4-layer stacks with strong analog/digital partitioning and interleaved GND pins on DF40.

AD9833-Based Function Generator with Multi-Rail Linear PSU and Star-Grounded Analog Output Stage

Battery-isolated 16-channel medical-grade EEG front end using dual ADS1299 analog front-ends and an STM32F405 host with integrated WiFi and microSD (SDIO), featuring corrected isolation, and robust low-jitter clock distribution for dual ADS1299 #WiFi #microSD #Isolation #Clocking #ADS1299 #STM32

Battery-Powered 2-Layer LM358 Analog Replicator PCB with Dual-Gain Edge Potentiometer and Solid 12 V Ground Plane

TECHNICAL ASSIGNMENT AND DESIGN GUIDE Active Three-Way Crossover on NE5532 Powered by AM4T-4815DZ and Amplifiers TPA3255 (Updated Version) 1. GENERAL PURPOSE OF THE DEVICE The goal of the development is to create an active three-way audio crossover for one channel of a loudspeaker system, working with the following drivers: LF: VISATON W250 MF: VISATON MR130 HF: Morel MDT-12 Each frequency range is amplified by a separate power amplifier: LF: TPA3255 in PBTL mode (mono) MF + HF: second TPA3255 in stereo mode (one channel for MF, the other for HF) The crossover accepts a single linear audio signal (mono) and divides it into three frequency bands: Range Frequency Range LF 0 – 650 Hz MF 650 – 2500 Hz HF 2500 Hz and above Filter type: Linkwitz–Riley 4th order (24 dB/oct) at each crossover point (650 Hz and 2500 Hz). The crossover must provide: minimal self-noise; no audible distortion in the audible range; stable operation with NE5532 at ±15 V power supply; easy adjustment of the level for each band, as well as the overall level (via the input buffer). 2. FILTER TYPES AND BASIC OPERATING PRINCIPLES Each filter is implemented as two cascaded Sallen–Key 2nd order (Butterworth) stages, resulting in a final 4th order LR4 filter. Topology: non-inverting Sallen–Key, optimal for NE5532. For all stages: Cascade gain: K ≈ 1.586 This provides a Q factor of 0.707 (Butterworth), which in combination gives a Linkwitz–Riley 4th order. 3. COMPONENT VALUES FOR FILTERS 3.1 Universal Parameters RC chain capacitors: 10 nF, film capacitors, tolerance ≤ 5% Resistors: metal-film, tolerance ≤ 1% The gain of each stage is set by feedback resistors: Rf = 5.9 kΩ Rg = 10 kΩ K ≈ 1 + (Rf / Rg) ≈ 1.59 The circuit should allow for the installation of a small capacitor (10–47 pF) in parallel with Rf (footprint provided) for possible stability correction (not mandatory to install in the first revision). 3.2 650 Hz Filters (Low-frequency boundary for MF) These are used for the division between W250 and MR130. LP650 — Low-frequency Filter 2nd Order R1 = 24.9 kΩ R2 = 24.9 kΩ C1 = 10 nF C2 = 10 nF Two stages: LP650 #1 and LP650 #2. HP650 — MF High-frequency Filter 2nd Order Same values: R1 = 24.9 kΩ R2 = 24.9 kΩ C1 = 10 nF C2 = 10 nF Two stages: HP650 #1 and HP650 #2. 3.3 2500 Hz Filters (Upper boundary for MF) These are used for the division between MR130 → MDT-12. LP2500 — High-pass MF Filter R1 = 6.34 kΩ R2 = 6.34 kΩ C1 = 10 nF C2 = 10 nF Two stages: LP2500 #1 and LP2500 #2. HP2500 — High-frequency Filter Same values: R1 = 6.34 kΩ R2 = 6.34 kΩ C1 = 10 nF C2 = 10 nF Two stages: HP2500 #1 and HP2500 #2. 4. OPERATIONAL AMPLIFIERS The NE5532 (dual op-amp, DIP-8 or SOIC-8) is used. A minimum of 4 packages (8 channels) for filters: NE5532 Function U1A, U1B LP650 #1, LP650 #2 (LF) U2A, U2B HP650 #1, HP650 #2 (Lower MF cut-off) U3A, U3B LP2500 #1, LP2500 #2 (Upper MF cut-off) U4A, U4B HP2500 #1, HP2500 #2 (HF) Additionally: U5 — input buffer / preamplifier (both channels) If necessary, an additional NE5532 (U6) for the balanced input (see section 6.2). All NE5532 should have local decoupling for power supply (see section 5.1). 5. CROSSOVER POWER SUPPLY AM4T-4815DZ DC/DC module is used: Input: 36–72 V, connected to the 48 V power supply for TPA3255 amplifiers. Output: +15 V / –15 V, up to 0.133 A per side. Maximum output capacitance: ≤ 47 µF per side (according to the datasheet). 5.1 Power Filtering Input (48 V): RC variant (simpler, acceptable for the first revision): R = 1–2 Ω / 1–2 W C = 47–100 µF (for 63 V or higher) LC variant (preferred for improved noise immunity): L = 10–22 µH C = 47–100 µF The developer may implement LC if confident in choosing the inductance and its parameters. Output +15 V and –15 V (general filtering): Electrolytic capacitor 10–22 µF per side 100 nF (X7R) per side to GND Local decoupling for NE5532 (REQUIRED): For each NE5532 package: 100 nF between +15 V and GND 100 nF between –15 V and GND Place as close as possible to the op-amp power pins (short traces). Additional local filtering for power lines: For each NE5532, decouple from the ±15 V main rails: Either 4.7–10 Ω resistor in series with +15 V and –15 V, Or ferrite bead in each rail. After this component, place local capacitors (100 nF + 1–4.7 µF) to ground. 6. INPUT TRACT: INPUTS, BUFFER, ADJUSTMENT 6.1 Unbalanced Input (RCA / Jack / Linear) The main mode is the unbalanced linear input, for example, RCA. Input tract structure: RF-filter and protection: Signal → series resistor Rin_series = 100–220 Ω After resistor — capacitor Cin_RF = 470–1000 pF to GND This forms a low-level RF filter and reduces high-frequency noise. DC-block (low-pass HP-filter): Capacitor Cin_DC = 2.2–4.7 µF film in series Resistor to ground Rin_to_GND = 47–100 kΩ Cut-off frequency — negligible in the audio range but removes DC. Input buffer / preamplifier (NE5532, U5): Non-inverting configuration. Input — after DC-block. Gain: adjustable, e.g., Rg_fixed = 10 kΩ (to GND through trimmer) Rf = 10–20 kΩ + footprint for trimmer (e.g., 20 kΩ) The gain should be in the range of 0 dB to +10…+12 dB. Possible configuration: Rg = 10 kΩ fixed Rf = 10 kΩ + 10 kΩ trimmer in series. This allows adjusting the overall level of the crossover according to the source and amplifier levels. Buffer output: A low-impedance output (after NE5532) This signal is simultaneously fed to the inputs of all filters: LP650 (LF) HP650 → LP2500 (MF) HP2500 (HF) 6.2 Balanced Input (XLR / TRS) — Optional, but laid out on the board The board should allow for a balanced input, even if it’s not used in the first revision. Implementation requirements: XLR/TRS connector (L, R, GND) or separate 3-pin header. Simple differential receiver on NE5532 (extra U6 package or use one channel of U5 if sufficient). Circuit: classic instrumentation amplifier or differential amplifier: Inputs: IN+ and IN– Output — single-ended signal of the same level (or slightly amplified), fed to DC-block and buffer (or directly to the buffer if integrated). Switching between balanced/unbalanced mode: Implement using jumpers / bridges or adapters: Either switch before the buffer, Or use two separate pads, one of which is unused. All balanced input grounds must be connected to the same AGND point as the unbalanced input to avoid ground loops. 7. LEVEL ADJUSTMENT OF BANDS (BEST METHOD) The level adjustment of each band (LOW, MID, HIGH) is required to match the sensitivity of the speakers and amplifiers. Recommended method: After each full filter (after LP650×2, MID-chain HP650×2 → LP2500×2, HP2500×2), install: A passive attenuator: Series: Rseries (0–10 kΩ, adjustable) Shunt: Rshunt to GND (10–22 kΩ, fixed or adjustable) For simplicity and reliability: Implementation on the board: For each band (LOW, MID, HIGH) provide: Pad for multi-turn trimmer 10–20 kΩ as a divider (between signal and ground) in the "level adjustment" configuration. If adjustment is not needed — install a fixed divider (two resistors) or simply use a jumper. It is preferable to use: For setup: multi-turn trimmers 10–20 kΩ, available on the top side of the board. Nominals for the initial configuration can be selected through measurements, but the PCB should have flexibility. This provides: Accurate balancing of band volumes without interfering with the filters; Flexibility for fine-tuning to the specific characteristics of the speakers. 8. INPUTS AND OUTPUTS OF THE CROSSOVER (FINAL) 8.1 Inputs 1× Unbalanced linear input (RCA or 3-pin header) 1× Balanced input (XLR/TRS or 3-pin header) — optional, but space must be provided on the board. Input impedance (unbalanced after RF-filter): 22–50 kΩ. The input tract must be implemented using shielded cables. 8.2 Outputs Outputs to amplifiers: Output Signal LOW OUT After LP650×2 (LF) MID OUT After HP650×2 → LP2500×2 (MF) HIGH OUT After HP2500×2 (HF) Each output: Series resistor 100–220 Ω (prevents possible oscillations and simplifies cable management). A nearby own AGND pad (ground output), so the signal pair SIG+GND runs together. Outputs should be compactly placed on 2-pin connectors (SIG+GND) or 3-pin (SIG+GND+reserve). 9. PCB DESIGN REQUIREMENTS 9.1 Board Number of layers: 2 layers Bottom layer: solid analog ground (AGND). 9.2 Component Placement Key principles: RC chains of each filter (R1, R2, C1, C2, Rf, Rg) should form a compact "island" around the corresponding op-amp. If elements are placed too far apart, the filter will not work correctly (calculated frequency and Q will shift). Feedback tracks (Rf and Rg) should be as short and direct as possible. The AM4T-4815DZ module should be placed: Far from the input buffer, Far from the first filter stages, If necessary, make a "cutout" in the ground under it to limit noise propagation. Place the input connector, RF-filter, and buffer on one side of the board, and the output connectors on the opposite side. 9.3 Ground The entire audio circuit uses one analog ground: AGND. Connect AGND to the power ground (48 V and amplifiers) at one point ("star"). The star should be implemented as: One point/pad where: The ground of the input, The ground of the filters, The ground of the outputs, The ground of the DC/DC. Avoid long narrow "ground" jumpers — use wide polygons with a single connection point. 9.4 Placement of Output Connectors Group LOW/MID/HIGH compactly. Each should have its own GND pad nearby. Route the SIG+GND pairs as signal pairs, avoiding large loops. 10. ADDITIONAL ELEMENTS: PROTECTION, TEST POINTS 10.1 Test Points (TP) Be sure to provide test points (pads): TP_IN — crossover input (after buffer) TP_LOW — LF filter output TP_MID — MF filter output TP_HIGH — HF filter output TP_+15, TP_–15, TP_GND — power control This greatly simplifies debugging with an oscilloscope. 10.2 Power Protection On the 48 V input — it is advisable to provide: Diode/scheme for reverse polarity protection (if possible), TVS diode or varistor for voltage spikes (optional). 10.3 Possible Stability Correction Pads for small capacitors (10–47 pF) in parallel with Rf in buffers and, if necessary, in some stages — in case of stability issues (this can be not installed in the first revision, but footprints should be provided). 11. BILL OF MATERIALS (BOM) Operational Amplifiers: NE5532 — 4 pcs (filters) NE5532 — 1–2 pcs (input buffer and balanced input) Total: 5–6 NE5532 packages. Resistors (1%, metal-film): 24.9 kΩ — 8 pcs 6.34 kΩ — 8 pcs 10 kΩ — ≥ 12 pcs (feedback, buffers, etc.) 5.9 kΩ — 8 pcs 22 kΩ — 1–2 pcs (input, auxiliary chains) 47–100 kΩ — several pcs (DC-block, input) 100 kΩ — 1 pc (if needed) 100–220 Ω — 4–6 pcs (outputs, RF, protection) 4.7–10 Ω — 2 pcs for each op-amp or group of op-amps (power filtering) — quantity to be clarified during routing. Trimmer Resistors: 10–20 kΩ multi-turn — one for each band (LOW, MID, HIGH) 10–20 kΩ — 1–2 pcs for the input buffer (overall gain adjustment). Capacitors: 10 nF film — 16 pcs (RC filters) 2.2–4.7 µF film — 1–2 pcs (input DC-block) 10–22 µF electrolytic — 2–4 pcs (DC/DC outputs) 1–4.7 µF (X7R / tantalum) — 1 pc for local power filtering (optional). 100 nF ceramic X7R — 10–20 pcs (local decoupling for each op-amp) 470–1000 pF — 1–2 pcs (RF filter on the input) 10–47 pF — optional for stability correction (Rf). Power Supply: AM4T-4815DZ — 1 pc Inductor 10–22 µH (if LC filter) — 1 pc R 1–2 Ω / 1–2 W — 1 pc (if RC filter). Connectors: Input (RCA + 3-pin for internal input) Balanced (XLR/TRS or 3-pin header) Outputs LOW/MID/HIGH — 2-pin/3-pin connectors. 12. TESTING RECOMMENDATIONS 12.1 First Power-up Apply ±15 V without installed op-amps. Check with a multimeter: +15 V –15 V No short circuits in the power supply. Install the op-amps (NE5532). Apply a sine wave of 100–200 mV RMS (signal generator). Check with an oscilloscope at TP: LP650 — should pass LF and roll off everything above 650 Hz. HP650 — should roll off LF, pass everything above 650 Hz. LP2500 — should roll off above 2500 Hz. **HP250 0** — should pass everything above 2500 Hz. 12.2 Phase Check The Linkwitz–Riley 4th order should give a flat frequency response when summed at the crossover points. This can be verified with REW/Arta. 12.3 Noise Check If there is noticeable "shshsh" or whistling: Check: Grounding layout (star) Placement and filtering of AM4T-4815DZ Presence and proper installation of all 100 nF and local filters. 13. FINAL RECOMMENDATIONS FOR BEGINNERS Do not rush, build the circuit step by step: input → buffer → one filter → test, then continue. Check component values at least twice before soldering. Filters should be routed as compact "islands" around the op-amp, do not stretch R and C across the board. Always remember the rule: "The feedback trace should be as short as physically possible." Before ordering the PCB, make a "paper prototype": print at 1:1, cut it out, place real components to check everything fits.

Ultra-Stable 850 nm, 1 mW VCSEL Module with Low-Noise Constant-Current Driver and Analog Modulation

Arduino-based 14-Panel LED and Button Controller with Analog Ladder Input

Simple inline 2 pin header analog filter using common 603 sized components

Design a schematic using an ESP32-S3 microcontroller that functions as a USB HID gamepad. The system includes two analog joysticks (each with X and Y axes), four normally open push buttons, and one status LED to indicate HID connection. Each joystick has two analog outputs connected to ADC pins. The push buttons connect to digital GPIOs with 10kΩ pull-down resistors. The status LED is connected to a digital GPIO through a 220Ω resistor. Place the ESP32-S3 in the center of the schematic, the joysticks to the left and right, and two buttons above each joystick. The circuit is powered by USB.

An analog ASIC designed to clock nonlinear arena ops.

I want to make an analog PID calculator of OPAmps