Production-ready ESP32-DEVKITC-32UE festival carousel horse LED controller schematic with organized Power, ESP32 + Level Shifter + LEDs, Inputs, and DMX + OLED blocks.

ESP32-S3 intelligent egg incubator schematic with camera-based egg verification, load-cell assessment, environmental sensing, heater/humidifier/fan control, servo turning, and OLED status display.

This circuit is an ultrasonic distance meter based on an ATTiny2313 microcontroller. It uses an HC-SR04 ultrasonic sensor to measure distance and displays the results on an OLED display. The power supply is constructed using a Boost converter (TPS613222A) and a 2-cell AA battery. Additionally, it also includes ISP for programming, RESET and START switches, and LED indicators. #project #Template #projectTemplate #ultrasonic #OLED #arduino #attiny2313 #TPS613222A #ISP #referenceDesign #simple-embedded #microchip #template #reference-design .

Compact ESP32-S3 AI robot controller with DevKitC-1 module, 2S Li-ion power input, 5V buck regulator, optional clean 3.3V rail, TB6612FNG dual motor driver, OV2640 camera FPC, I2S audio, OLED, ultrasonic and TCRT5000 sensor headers, and a compact 2-layer PCB prepared for Gerber export.

Compact 45 mm x 35 mm 4-layer agricultural IoT sensor node using an ATmega4808, AMS1117-3.3 linear regulation from 12 V input, RS-485 Modbus RTU half-duplex, local I2C sensors, 0.96 inch OLED, status LED, and a 12 V solenoid valve driver with top-side sensors/display and bottom-side MCU/power partitioning.

Single-phase student energy meter using ATM90E26 metering IC, STM32F103 MCU, OLED display, USB-UART communication, transformer voltage sensing, and SCT013 current sensing. Designed for a 2-layer PCB within 150 mm x 150 mm and a BOM target below 50 EUR.

This is a smart watch project based on E73-2G4M04S1A module with SoC nRF52810 on board. OLED display and coin battery #wearable #nRF52810 #E73 #Ebyte #BLE #referenceDesign

Compact kayak and canoe impact sensor PCB with USB-C Li-ion charging, ATmega328P-AU control, ADXL345 breakout sensing, 3.3V regulated power, OLED and ISP headers, and corner mounting holes.

Compact kayak and canoe impact sensor PCB with USB-C Li-ion charging, ATmega328P-AU control, ADXL345 breakout sensing, 3.3V regulated power, OLED and ISP headers, and corner mounting holes.

Arduino-based vibration sensor module with SSD1306 OLED display for real-time vibration readings

ESP32-S3 Wearable Audio Streaming Pendant (USB-C + LiPo + I2S Mic + microSD + OLED)

AeroHUD VariScope Mark 1 - ESP32-S3 RF module vario/airspeed HUD with Qwiic OLED and SDP810, GPS, USB-C data+charging

This project is a WiFi RF-ID Lock, which uses a Espressif ESP-8684 microcontroller for WiFi connectivity and a Handson Technology RC522 for RF-ID functionality. It also includes an OLED display and user control via a switch. A step-up power converter ensures consistent 3.3V power. #WiFi #MCU #ReferenceDesign #project #ESP8684 #lock #OLED #referenceDesign #simple-embedded #espressif #template #reference-design

Children’s Color Vision Screening Game using ESP32, TCS3200 Sensor, and OLED Display

Smart Wellhead Controller V1.1: ESP32 + LoRa Industrial IoT Node with Solar Power, Deep-Sleep Leak Sensing, and OLED HMI. Now upgraded with a solar charging and battery management stage featuring a TP4056/CN3791 charger IC, power-path switching, Li-ion battery protection, and integrated 3.3 V rail supply. #PowerBlock #SolarCharging #BMS

ESP32-WROOM-32 Wearable Health Monitor with MAX30102, MPU6050, OLED, Camera Interface, and Advanced Power Management

Project Title: Plant Monitoring and Irrigation System Overview: This system is based on the ESP32-S3 and is designed to manage irrigation for a multi-floor building. Key Features: Multi-Floor Operation: The system controls three separate floors. Each floor's irrigation can be managed independently. Irrigation and Pump Control: Each floor uses a solenoid valve to regulate water flow. The solenoid valves are operated via MOSFETs. A relay engages an AC water pump when a MOSFET triggers a solenoid valve. Hardware Interconnects: Screw Terminal connectors are added for connecting the solenoid valves and the motor pump. A DC Jack is included to supply power to the system. User Interface & Connectivity: Two JST connectors are provided for integrating an OLED display, a rotary encoder, and a pushbutton. Future enhancements may include the addition of soil moisture sensors. Remote Control: The system is designed for future integration with Blynk IoT. Blynk IoT will offer both manual control and timer-based irrigation modes for each floor.

To optimize your 4-layer board manufacturing process with Seeed Studio Fusion, utilize this comprehensive template. It incorporates a majority of the essential manufacturing constraints as global rules, ensuring a smoother and more efficient production workflow. #project-template #template #manufacturer-design-rules This project is a vessel monitoring system built using Seeed Studio Xiao Sense, Xiao Expansion Board with OLED, a UART WiFi module, a normally open float switch, and a UART SIM800L cellular module. The system displays a 30-second countdown on the OLED screen, calibrates the IMU sensor, converts to Euler angles, and stores these values for comparison with future readings. It also sets up the WiFi module as an access point to configure the vessel's name, contact numbers, and angle thresholds for list and trim notifications. Reports are sent at specified times via the cellular module.

This is an Energy Meter project leveraging an ATTiny85 microcontroller (U1) to sense current through an ACS712 module (U2). It displays the data in real-time on an OLED display (OLED1) and interacts with three buttons (NEXT, MENU, OK). This compact energy meter is suitable for edge computing and low-power Internet of Things (IoT) applications #project #keypad #arduino #attiny85 #ISP #referenceDesign #edge-computing #edgeComputing #microchip #template #reference-design

This project is a WiFi RF-ID Lock, which uses a Espressif ESP-8684 microcontroller for WiFi connectivity and a Handson Technology RC522 for RF-ID functionality. It also includes an OLED display and user control via a switch. A step-up power converter ensures consistent 3.3V power. #WiFi #MCU #ReferenceDesign #project #ESP8684 #lock #OLED #referenceDesign #simple-embedded #espressif #template #reference-design

This circuit is an ultrasonic distance meter based on an ATTiny2313 microcontroller. It uses an HC-SR04 ultrasonic sensor to measure distance and displays the results on an OLED display. The power supply is constructed using a Boost converter (TPS613222A) and a 2-cell AA battery. Additionally, it also includes ISP for programming, RESET and START switches, and LED indicators. #project #Template #projectTemplate #ultrasonic #OLED #arduino #attiny2313 #TPS613222A #ISP #referenceDesign #simple-embedded #microchip #template #reference-design

This project is a WiFi RF-ID Lock, which uses a Espressif ESP-8684 microcontroller for WiFi connectivity and a Handson Technology RC522 for RF-ID functionality. It also includes an OLED display and user control via a switch. A step-up power converter ensures consistent 3.3V power. #WiFi #MCU #ReferenceDesign #project #ESP8684 #lock #OLED #referenceDesign #simple-embedded #espressif #template #reference-design

This is a smart watch project based on E73-2G4M04S1A module with SoC nRF52810 on board. OLED display and coin battery #wearable #nRF52810 #E73 #Ebyte #BLE #referenceDesign

Greenhouse controller with temperature and humidity control Input voltage 12v led voltage: 12v humidifier voltage: 5V Display: i2c 0.96 OLED display sensor: htu21d i2c

This module is a minimalist Arduino Watch design. Consisting of a Microchip ATTINY85-20SU microcontroller, an OLED display for visual output, two user buttons for interface, and a Li-ion Battery for power. The schematic also includes graphic user interface with ISP for programming and minimal passive components for functionality. #project #Template #projectTemplate #reusable #module #simple-embedded #microchip #arduino #sublayout