Slide Switch SPDT Through Hole, Right Angle The SLW-864574-5A-RA-N-D, manufactured by Same Sky (formerly CUI Devices), is a single-pole double-throw (SPDT) slide switch with a right-angle, through-hole mounting configuration. It features a raised actuator for easy manual operation and is intended for PCB-based applications where space is limited but dependable switching is required. Key Features Switch Type: Slide switch (manual) Circuit Configuration: SPDT (Single Pole Double Throw) Switch Function: ON–ON (selects between two circuits) Contact Timing: Non-shorting (break-before-make) Mounting Type: Through-hole, right-angle Actuator: Raised slide, ~5 mm height Electrical & Mechanical Characteristics Rated Voltage: 50 VDC Rated Current: up to 500 mA Contact Resistance: ≤ 100 mΩ Insulation Resistance: ≥ 100 MΩ Operating Temperature: -20°C to +70°C Mechanical/Electrical Life: ~10,000 cycles Physical Characteristics Dimensions: approx. 8.6 × 4.5 × 6–7 mm Actuator Travel: ~2 mm Termination: PC pins (through-hole soldering) Orientation: Horizontal (right-angle insertion into PCB) #CommonPartsLibrary #Switch

This is a QRE1113 opto-reflective sensor module, using a 47K pull-up resistor (R2) and a 100 Ohm resistor (R1). It includes a 1µF capacitor (C1) for stability and attaches to a JST connector (J1) for easy interfacing. Power is provided via VCC, with the output signal (OPTO_OUT) fed back. #OpticalSensor #industrialSensing #reusable #module #industrialsensing #onsemi #sublayout

USB to Serial Interface, SSOP-28 FTDI USB Serial SSOP*5.3x10.2mm*P0.65mm* The FT232RL is a full-speed USB 2.0 to asynchronous serial data transfer IC. It integrates all the necessary USB protocol handling and UART interface logic, making it very easy to add USB connectivity to embedded devices without requiring complex firmware development. It is commonly used in development boards (like Arduino clones), USB-to-TTL converters, and debugging interfaces. Key Features USB Interface Fully compliant with USB 2.0 Full-Speed (12 Mbps) Integrated USB transceiver (no external components required) Supports USB suspend/resume modes Internal EEPROM for storing USB descriptors (no external EEPROM needed) Serial (UART) Interface Supports standard UART communication (TX, RX) Configurable baud rates from 300 bps up to 3 Mbps Supports hardware flow control (RTS/CTS, DTR/DSR) Bit-bang mode for simple GPIO control Integrated Components Built-in clock generator (no external crystal required) Internal EEPROM for configuration Integrated voltage regulator (3.3V output available for external use) Power Features Operates from 3.3V to 5V Can be powered directly from USB (bus-powered) Low power consumption with sleep mode Driver Support Virtual COM Port (VCP) drivers available for: Windows Linux macOS Also supports direct D2XX driver for advanced applications Package Typically available in SSOP-28 package Common Applications USB-to-serial converters (TTL/RS232) Microcontroller programming and debugging Embedded system communication Industrial and instrumentation interfaces

A high accuracy ambient light digital 16-bit resolution sensor in a miniature transparent 6.8 mm x 2.35 mm x 3.0 mm package. It includes a high sensitive photo diode, a low noise amplifier, a 16-bit A/D converter and supports an easy to use I2C bus communication interface.

Wio-E5 Dev Kit embedded with Wio-E5 STM32WLE5JC LoRa module that supports Long Range protocol on the global frequency band. It provides full GPIOs, which support various data protocols and interfaces such as RS485, Grove, male/female headers, etc. This makes it user-friendly because it allows for easy and flexible connections to other devices or components. It would be a perfect choice for fast testing and rapid prototyping of your Long Range IoT projects.

Crank up your robotics with powerful Adafruit DRV8871 motor driver breakout board. This motor driver has a lot of great specs that make it useful for a wide variety of mechatronics. In particular, the simple resistor-set current limiting and auto-magic PWM support make it super easy to use with just about any brushed DC motor.

Life has its ups and downs, so why not measure them? The MPL3115A2 is a MEMS pressure sensor that provides Altitude data to within 30cm (with oversampling enabled). The sensor outputs are digitized by a high resolution 24-bit ADC and transmitted over I2C, meaning it's easy to interface with most controllers. Pressure output can be resolved with output in fractions of a Pascal, and Altitude can be resolved in fractions of a meter. The device also provides 12-bit temperature measurements in degrees Celsius. #Sublayout #Submodule #Altitude #PressureSensor #MPL3115A2

8km UART Through Hole RF Transceiver Modules and Modems RoHS,3.3V~5.2V,-40 ~ 80C The E32-433T30D is based on the Semtech SX1278 LoRa chipset and uses LoRa spread-spectrum modulation to achieve long-distance, highly reliable wireless communication even in noisy environments. It communicates with a microcontroller via UART (serial interface), making it easy to integrate with Arduino, ESP32, STM32, and similar systems. It is commonly used for IoT telemetry, remote control systems, sensor networks, and industrial monitoring, especially where GSM/Wi-Fi is unavailable or impractical. Key Features Frequency range: 410–441 MHz (433 MHz default) RF output power: 21–30 dBm (up to 1 W high-power version) LoRa modulation: High sensitivity and strong anti-interference Communication distance: up to ~8 km (open area, ideal conditions) Interface: UART TTL serial (3.3 V logic level) Sensitivity: around -147 dBm for long-range reception Low data rate support: ~0.3 kbps to 19.2 kbps Half-duplex communication (TX/RX not simultaneous) Configurable modes: normal / wake-up / power-saving / sleep via M0 & M1 pins Compact module size with SMA antenna connector Wide operating temperature: -40 °C to +85 °C Important Notes Requires external microcontroller (MCU) for operation (not standalone). Must not leave M0 and M1 pins floating (must be defined HIGH/LOW or GND). Works best with proper 433 MHz antenna (2–5 dBi recommended). Power supply must be stable (typically 5V with sufficient current capability). For maximum range, line-of-sight + correct antenna height matters more than raw power. Applications Smart agriculture monitoring Remote sensor networks Utility meter reading (water/gas) Industrial telemetry systems Drone/robot communication links Remote control & automation systems #E32_433T30D #Ebyte #LoRa #SX1278 #WirelessModule #IoT #Telemetry #LongRangeCommunication #UART #433MHzLoRa #EmbeddedSystems

Connector Header Through Hole, Right Angle 10 position 0.100" (2.54mm) The 1761607-3 is a pluggable terminal block connector manufactured by TE Connectivity. It is designed for reliable wire-to-board connections in industrial and electronic applications. The connector supports screw-clamp termination, allowing secure and reusable wire connections. Its modular design enables easy installation and maintenance, making it suitable for control systems, power distribution, and signal interfacing. Key Features Pluggable terminal block connector Screw-clamp wire termination Reliable mechanical and electrical connection Modular and field-serviceable design Suitable for industrial environments Electrical Characteristics Rated voltage: up to 300 V (typical, application dependent) Rated current: up to 8 A (depending on wire size and conditions) Contact resistance: low contact resistance for stable conductivity Insulation resistance: high insulation resistance Mechanical Characteristics Number of positions: 3 Pitch: 3.5 mm Termination type: screw clamp Wire size range: typically 26 AWG to 16 AWG Mounting type: through-hole PCB Mating type: pluggable header interface Material Properties Housing material: high-temperature thermoplastic Contact material: copper alloy Contact plating: tin plating Flammability rating: UL94 V-0 Environmental Specifications Operating temperature range: −40°C to +105°C RoHS compliant Suitable for industrial applications Applications Industrial control systems Power supply connections Signal interface modules Automation equipment HVAC and building control systems Compliance & Standards RoHS compliant UL recognized (application dependent) IEC standard compliant terminal block design #commonpartslibrary #connector #header

Pressure Sensor -0.57PSI ~ 0.57PSI (-3.92kPa ~ 3.92kPa) Gauge Male - 0.1" (2.5mm) Tube 7 b 12-SMD, No Lead, Top Port The MMR920C04ARE, manufactured by Mitsumi Electric, is a surface-mount pressure sensor that measures low differential (gauge) pressure with high accuracy. It integrates sensing, signal conditioning, and digital output in a single package, making it easy to interface with microcontrollers. Sensor Type: MEMS-based gauge pressure sensor Pressure Range: ±0.57 PSI (±3.92 kPa) Output Interface: Digital (supports I²C and SPI) Resolution: 7-bit output (internally higher-resolution processing available) Supply Voltage: 3.0 V to 3.6 V Accuracy: حوالي ±0.65% full scale Package: 12-SMD, no-lead, top-port (compact ~7×7×7.2 mm) Port Type: 2.5 mm tube (barbless) for airflow or gas connection Features: Built-in temperature compensation Fast sampling capability Factory-calibrated digital output #CommonPartsLibrary #Sensor #Pressure-Sensor #Transducer