I want to create a standard interface from my PCBs to my test equipment. My equipment: PSU: Rigol DP832 Scope: Siglent SDS 1202X-E WaveGen: Siglent SDG810 Logic Analyzer: DSLogic Plus 400MHz VNA: NanoVNA V2 6 scope channels (4 1X, 2 10X) 8 Logic Analyzer channels 1 Wavegen channel 4 Power Nets ( 2 pins each) (tie power nets to oscilloscope inputs) #template #testing

I designed a Raspberry Pi pico-like board using only AI

Welcome to your new project. Imagine what you can build here.

Welcome to your new project. Imagine what you can build here.

Welcome to your new project. Imagine what you can build here.

Welcome to your new project. Imagine what you can build here.

Generator i dozownik Dwutlenku chloru

@copilot help I am building a 42 v bus satellite eps system

The purpose of this project is to get to know the UI of Flux, whilst also creating a project that I am interested in and that I can enjoy.

I want make a board that trigger a green and red LED with three wire, 0V, 24V and output of proximity switch. but i want output wire remain 0V when not connected.

I am practicing how to use fluz AI

This is a 2 stage IR sensor circuit intended to be used as a ballistic speedometer/chronograph for my Coilgun. I based it off a common design for IR proximity sensors. There are 2 output pins to a microcontroller, and +/-pins for 2 IR receivers, 2 IR emitters, and 2 green LEDs to show when the stage is active. When the beam is broken the voltage on the microcontroller output pins will change, allowing me to code proper coil stage firing timing. The potentiometers are for tuning the sensitivity.

NOTICE: This board has a incorrectly sized battery holder. If building this revision, also build the [adaptor board](flux.ai/markwuflux/adaptor-board-for-universal-electronic-derailleur-v1) Cable Index Shifting Electronic Derailleur. The first version just uses a linear actuator because I suck at ME design. I imagine it would be pretty easy to build a reeling one with positional feedback.

A simple 1-to-3 buffered mult - Eurorack-talk for an audio/CV distributor The board itself is a 3U 4hp rack-mountable module This circuit was designed by https://www.skullandcircuits.com/utilities-buffered-multiple/ and their T&Cs apply to commercial use (I built these for myself)

I want to build midi controller with 16 pads, 8 rotary knobs and 12 function buttons. It also should have built in audio interface with line in/line out ports. The controller will be connected via usb-c.

I have a military trailer w/ a generator on it. all brake/signal lights are 24V, I would like to be able to tow it with a truck with a standard 12v 7 way RV plug.

Design an 8-input to 3-output encoder WITH PRIORITY, considering: 1. truth table. 2. Output equations. 3. Logic diagram. You can use 2, 3 or 4 input logic gates if you prefer. You can do it in a notebook or in a simulator like multisim. If it is in a notebook, make sure that everything looks clean, so I suggest you do it first in draft and then to hand it in.

I hope it will work

Change History from V1: -13.56MHz tuning -larger instruction font -put some stuff on the back #template I wanted to create a business card that has some functionality and shows off a bit of my portfolio IRL: -NFC to my flux page -here's the [instructables](https://www.instructables.com/PCB-Business-Card-With-NFC-Make-Yours-With-NFC-QR-/) -Put a bunch of modules on it Find the BoM [here](https://www.digikey.com/short/2db2vnmp)

this is a custom board using the MCU "STM32F107RBTx". the reason why i chose this MCU is because i wanted to implement circuits for ethernet communication, CAN communication and USB communication.

Change History from V1: -13.56MHz tuning -larger instruction font -put some stuff on the back #template I wanted to create a business card that has some functionality and shows off a bit of my portfolio IRL: -NFC to my flux page -here's the [instructables](https://www.instructables.com/PCB-Business-Card-With-NFC-Make-Yours-With-NFC-QR-/) -Put a bunch of modules on it Find the BoM [here](https://www.digikey.com/short/2db2vnmp)

Change History from V1: -13.56MHz tuning -larger instruction font -put some stuff on the back #template I wanted to create a business card that has some functionality and shows off a bit of my portfolio IRL: -NFC to my flux page -here's the [instructables](https://www.instructables.com/PCB-Business-Card-With-NFC-Make-Yours-With-NFC-QR-/) -Put a bunch of modules on it Find the BoM [here](https://www.digikey.com/short/2db2vnmp)

Welcome to your ne I w project. Imagine what you can build here.

This is a speech output model for a NIFPES (Nitrogen Injection Fire Prevention and Exhaustion System) machine. ESP32 is being used where it is connected with a limit switch LXW20-11M and ESP32 is connected with DFPlayer mini MP3 Speaker module and the speaker module is further connected to a speaker. This model is powered by a PLC SMPS of 24V and is connected to the door of the control panel of the machine. Function:- Now whenever the door is opened or closed, there is a speech output from the speaker "The door is open" or "The door is closed". Further work to be done:- I need to integrate the fire alarm signals and 20 more signals of 24v each from the PLC output to the ESP32 so that there can be speech outputs whenever any signal is high.

Change History from V1: -13.56MHz tuning -larger instruction font -put some stuff on the back #template I wanted to create a business card that has some functionality and shows off a bit of my portfolio IRL: -NFC to my flux page -here's the [instructables](https://www.instructables.com/PCB-Business-Card-With-NFC-Make-Yours-With-NFC-QR-/) -Put a bunch of modules on it Find the BoM [here](https://www.digikey.com/short/2db2vnmp)