The LoST 3296 board features an Low Power STM32, an RFM95 Module for LoRA connectivity and a connector to interface different sensors. You can hook up a UART module, I2C module and a module using the RS485. The board is powered by the USB-C port

This is a LoRa remote control project built around a Raspberry Pi RP2040 SoC and the RFM95W LoRa module. The design includes user interface features such as multiple buttons and LEDs, power management components, and a temperature sensor. The project utilizes SPI, I2C, and USB interfaces for communication and control. #referenceDesign #simple-embedded #raspberrypi #lora #template #reference-design

10/100 Base-T/TX PHY Ethernet controller that supports PoE with SPI Interface. Based on W5500. Can be used as PoE injector. #project #referenceDesign #template #w5500 #PoE #EtherNet #RJ5

This ADM3054BRWZ-RL7-based reference design is a CAN bus transceiver circuit, providing reliable data communication over the CAN network. The design features a range of capacitors and resistors to ensure signal integrity, and a NUP2105L for voltage protection. It's ideal for applications requiring reliable data communication in an automotive or industrial environment. #referenceDesign #project #CANbus #interface #transceiverCircuit #ADM3054 #ADM3054BRWZ-RL7 #referenceDesign #canbus #texas-instruments #template #reference-design #reference-design

Interface for Wemos D1 mini to sct-013 current sensor via a 3.5mm jack

Reference design for PCM5102A 2VRMS DirectPath™, 112dB Audio Stereo DAC with 32-bit, 384kHz PCM Interface #project-template #DAC #audio #project

The TCA9555 is a 16-bit I/O expander, designed by Texas Instruments, that is compatible with the I2C and SMBus communication protocols. It operates between 1.65 and 5.5 volts and can be used to extend the functionality of most microcontroller families via the I2C interface. The system master can enable the I/O pins as either inputs or outputs and can invert the polarity of the Input Port register. This part is widely used in applications like servers, personal computers, automation equipment, routers, and other electronics with limited GPIO availability.

This is a reference design of MAX3051 with a standard configuration for normal mode #MAX3051 #can #interface #template #referenceDesign #canbus #analogdevices #transceiverCircuit #reference-design

This is a WiFi to Infrared (IR) gateway reference design leveraging an ESP32-S3 microcontroller for WiFi connectivity. It also incorporates a Type-C USB interface for data and power, 3 LEDs (red, green, & IR), and voltage regulation. It facilitates wireless control of IR devices, suitable for home automation projects. #referenceDesign #edge-computing #espressif #template #IR #project #reference-design

X9C103 digital potentiometer with a serial, 3 wire interface. 10K.

This TCAN1043HDQ1-based reference design is a CAN bus transceiver circuit that facilitates robust data communication across the CAN network. The design incorporates a variety of capacitors and resistors to maintain signal quality, and it employs a NUP2105L for voltage protection. This circuit is ideally suited for applications that need reliable data communication in automotive or industrial settings. #referenceDesign #project #CANbus #interface #transceiverCircuit #TCAN1043HDQ1 #TCAN1043 #template #canbus #texas-instruments #reference-design

Sensor and Detector Interface 5.5V 0.7mA SPI Interface 8-Pin SOIC N T/R #CommonPartsLibrary #IntegratedCircuit #Interface #Sensor-Detector

The TUSB8041, developed by Texas Instruments, is a four-port USB 3.0 hub intended for use in computer systems, docking stations, monitors, and set-top boxes, providing simultaneous SuperSpeed USB and high-speed/full-speed connections on the upstream port as well as on the downstream ports. This component supports battery charging features, enabling Charging Downstream Port (CDP) and Dedicated Charging Port (DCP) modes, compliant with the Chinese Telecommunications Industry Standard YD/T 1591-2009, and introduces an automatic mode for transparent support for BC devices and devices supporting Divider Mode charging solutions. It offers customization through OTP ROM, I2C EEPROM or via an I2C/SMBus slave interface for Vendor ID (VID), Product ID (PID), port customizations, and manufacturer and product strings. The TUSB8041 comes in a 64-pin RGC package and is available in both commercial (0°C to 70°C) and industrial (-40°C to 85°C) temperature ranges, part numbers TUSB8041 and TUSB8041I respectively, with an operating voltage requirement of 3.3V for I/O and 1.1V for the core. This hub doesn't require special drivers as it's designed to work seamlessly with any operating system supporting the USB stack, making it a highly adaptable solution for expanding USB connectivity in a wide range of applications.

This project is a Battery Management System (BMS) built around STMicroelectronics' STC3115AIQT battery monitor IC. It uses I2C for communication, features alarm management, and supports battery charging. The power supply, battery connection points, and debug interface are facilitated through connectors. #project #Template #charger #monitor #reusable #module #batterycharger #template #bms #STC3115 #stm

This module is a minimalist Arduino Watch design. Consisting of a Microchip ATTINY85-20SU microcontroller, an OLED display for visual output, two user buttons for interface, and a Li-ion Battery for power. The schematic also includes graphic user interface with ISP for programming and minimal passive components for functionality. #project #Template #projectTemplate #reusable #module #simple-embedded #microchip #arduino #sublayout

Design for hat board that interfaces with RPi CM4 IO board

Important Note: You must connect your own SPI/ICSP programming header if you want to burn the Arduino bootloader to the MCU. In this version, you must also provide your own UART interface. SMD Manufacturing: Need a hotplate and solderpaste Good to haves: - Oscillator Decoupling Caps Expose UART via connector Programming Button Onboard LED Reset Button You don't have to populate everything! Only these are mandatory: Reset Button Find the reference schematic here: https://www.arduino.cc/en/uploads/Main/ArduinoNano30Schematic.pdf

This project is a communication device designed with Adafruit's 3857 Microcontroller (U1) and Hoperf's RFM95W-915S2 RF module (U2). The microcontroller interfaces with the RF module via SPI protocol for wireless data transmission. The project also includes a capacitor (C1) and an SMA connector (J1). #LoRa #IoT #project #M4 #Adafruit

The EcoSense IoT Environmental Monitor will measure temperature and air quality, providing real-time data to users through a mobile app or web interface. The device will be compact, easy to install, and user-friendly, offering insights into the indoor environmental conditions to promote health and well-being. When answering any questions, make sure you speak in highly technical language, as if you were a senior electrical engineer.

This module is a minimalist Arduino Watch design. Consisting of a Microchip ATTINY85-20SU microcontroller, an OLED display for visual output, two user buttons for interface, and a Li-ion Battery for power. The schematic also includes graphic user interface with ISP for programming and minimal passive components for functionality. #project #Template #projectTemplate #reusable #module #simple-embedded #microchip #arduino #sublayout

This project is a motherboard for the ESP32-CAM module, which enables easy and flexible WiFi camera applications. The motherboard provides power supply, programming interface, and GPIO expansion for the ESP32-CAM. It also supports external sensors for more functionality. #motherboard #WiFi #MCU #ReferenceDesign #project #ESP32 #camera #reusable #module #edgeComputing #espressif #template

This project is a Battery Management System (BMS) built around STMicroelectronics' STC3115AIQT battery monitor IC. It uses I2C for communication, features alarm management, and supports battery charging. The power supply, battery connection points, and debug interface are facilitated through connectors. #project #Template #charger #monitor #reusable #module #batterycharger #template #bms #STC3115 #stm

The MAX485 TTL to RS-485 Interface Module allows MCUs to use the RS-485 differential signaling for robust long distance serial communications.

ATMEGA328-PU (U1) Setup Power Supply Connections: Connect U1:VCC to U2:5V@1 (5V power supply). Connect U1:GND to U2:GND@1 (Ground). Connect U1:AVCC to U2:5V@2 (Analog Power Supply for better ADC performance). Multiple GND pins (U2:GND@1, U2:GND@2, U2:GND@3, U2:GND@4) should all be connected to a common ground plane for stability. Serial Communication for Debugging: Connect U1:PD0 (RX) to U6:TXD. Connect U1:PD1 (TX) to U6:RXD. These connections enable serial communication between the microcontroller (ATmega328) and the USB-Serial adapter (CH340N) for programming and debugging. Sensor Data Acquisition: Given the components, the MLX90614ESF-ACC-000-SP (U4) is an infrared temperature sensor that could be used for vital detection. It uses an I 2 2 C interface. Connect U1:PC4 (SDA) to U4:PWM_SDA. Connect U1:PC5 (SCL) to U4:SCL_Vz. This allows the ATmega328 to communicate with the MLX90614ESF infrared temperature sensor. Additional Considerations: An analog-to-digital converter (ADC) or a specialized RF module designed for UWB radar applications would be necessary to capture and process radar signals for detecting human vitals through walls. The MAX270CWP+ (U3) could be used for audio signal processing but may not directly apply to UWB radar signal processing. Power Supply to Other Components Connect U6:VCC to U2:5V@1. Connect U4:VDD to U2:5V@2. Ensure all components' ground pins are connected to the common ground plane (U2:GND@1, GND@2, GND@3, GND@4)

A circuit for a gps tracker using stm32f103c8t6 and sim 808, that acquires and sends gps coordinates to a separate interfaced application. The circuit will be powered by a 12v dc battery so there a need for power regulation. there is a USB type micro B for code uploading.