Sensor using through hole LDR and power with SMT LED Resistors and PZT3904

Through Hole straight pin header, 01x10, 2.54mm pitch, single row #pinheader #tht #SimplifiedFootprint

Sensor using through hole LDR and power with SMT LED Resistors and PZT3904

Sensor using through hole LDR and power with SMT LED Resistors and PZT3904

Sensor using through hole LDR and power with SMT LED Resistors and PZT3904

This circuit can take an analog input, control a DC gearmotor, sense its direction and cumulative number of revolutions, and turn on and off three LEDs, in whatever way it is programmed. It can be repeatedly reprogrammed through a connector on the PCB. Powered by six AA batteries, it economizes on power by disconnecting some components when they are not in use.

Sensor using through hole LDR and power with SMT LED Resistors and PZT3904

Connector Header Through Hole 8 position 0.100" (2.54mm) #Generic #Connector #SimplifiedFootprint

Using the Raspberry Pi Pico microcontroller, I was able to design a hearing aid with volume control. The components and a description of why they were used: MCP3008 - CONVERTS ANALOG AUDIO SIGNALS INTO DIGITAL DATA CONVERTED BY THE MICROCONTROLLER MCP4725 - CONVERTS DIGITAL AUDIO SIGNALS TO ANALOG SO THE AUDIO CAN BE OUTPUTTED THROUGH A SPEAKER LM358 - USED TO AMPLIFY WEAK SIGNALS IN THE HEARING AID, REMOVES UNWANTED FREQUENCIES SPU0410LR5HQB - THIS COMPONENT IS A MICROPHONE, SPECIFICALLY CHOSEN BECAUSE IT IS OMNIDIRECTIONAL AND CAN CAPTURE AMBIENT SOUNDS, IT IS A SMALL COMPONENT PERFECTLY USED FOR NOISE REDUCTION, ASSISTING IN CAPTURING CLEAR AUDIO PAM8302AASCR - EFFICIENTLY AMPLIFIES AUDIO, AUDIO SIGNAL FROM DAC (VOUT) IS FED INTO THE INPUT OF THE AUDIO AMPLIFIER, WHICH OUTPUTS IDEAL FREQUENCY AUDIO CEM-1203(42) - SPEAKER WHICH OUTPUTS THE AUDIO AMPLIFIER MODIFIED FEATURE: POTENTIOMETER - WITH THE CCW CONNECTED TO GND, CW CONNECTED TO VDD, WIPER CONNECTED TO PIN 27 OF THE MICROCONTROLLER, THIS FEATURE IS A VOLUME ADJUSTER, WE ARE ABLE TO FULLY TURN OFF AND ON THE VOLUME BY ADJUSTING THE HEARING AID FOR THE IDEAL AUDIO OUTPUT

there is a buck boost converter that can be powered through Li-ion battery and output 3.3V @500 mA. powered by the TPS63051YFFR and in the same package as a standard Adafruit buck converter. input Voltage range:2.5V to 5.5V.

Through hole straight pin header, 1x04, 4 pin, 4-pin, horizontal, angled, 2.54mm pitch, 6mm pin lenght single row

The TCA9555, manufactured by Texas Instruments, is a low-voltage 16-bit I/O expander designed for both I2C and SMBus for operation with a supply voltage ranging from 1.65 V to 5.5 V. This component is aimed at providing general-purpose remote I/O expansion for most microcontroller families through the I2C interface. The TCA9555 is characterized by its low standby-current consumption of maximum 3.5 uA and includes notable features such as open-drain active-low interrupt output, 5-V tolerant I/O ports, and configurable slave addresses through 3 address pins. It is designed to assist in applications such as servers, routers, personal computers, personal electronics, and industrial automation equipment, among others. Its multiple package options, including TSSOP, SSOP, WQFN, and VQFN, accommodate different sizes and form factors suitable for diverse implementation requirements. The device distinguishes itself with a polarity inversion register and latched outputs capable of directly driving LEDs, showcasing versatility in usage. Its protection features exceed JESD 22 standards for ESD, ensuring robustness for industrial applications. The TCA9555's compatibility with various microcontrollers and support for up to 400-kHz I2C bus speed make it an efficient solution for expanding I/O capabilities in space-constrained applications.

An ESP32 DEV KIT with stepper and motor control outputs and accel. input. ESP32 programmed through d- and d+ pins of Micro USB

Power Barrel Connector Jack 2.10mm ID (0.083"), 5.50mm OD (0.217") Through Hole #commonpartslibrary #connector #barrel #jack #Power-Connector #PJ-044

Through-hole 9V NE555 astable timer circuit that blinks a red LED about once per second using a battery and on/off switch.

Welcome to your new project. Imagine what you can build here.

Guitar pedal starter template based on project by Mark Wu. Includes schematic and PCB layout for basic DIY pedal hardware. This includes two 1/4" jacks (one for input and one for output), a 9V power supply (including LED), a 3PDT true bypass wiring setup, and an example potentiometer that can be copy/pasted throughout the circuit. The headers are meant to be unpopulated so that wires can be soldered to the pads. PCB design rules imported from the JLCPCB 2-layer stackup template. #template

DIP-20 is a through-hole package with 20 pins arranged in two rows spaced 7.62mm apart. The body of the package is typically 27.94mm long and 10.16mm wide. DIP-20 is commonly used for a variety of integrated circuits and other electronic components. 20-DIP #part #template

Guitar pedal starter template based on project by Mark Wu. Includes schematic and PCB layout for basic DIY pedal hardware. This includes two 1/4" jacks (one for input and one for output), a 9V power supply (including LED), a 3PDT true bypass wiring setup, and an example potentiometer that can be copy/pasted throughout the circuit. The headers are meant to be unpopulated so that wires can be soldered to the pads. PCB design rules imported from the JLCPCB 2-layer stackup template. #template

Naze 32 Revision 6 Flight Controller Schematic At the heart of the Naze32 is a 32bit ST micro work horse of a processor, with untapped memory and cpu power and a host of equally impressive sensors. The Naze is also matched up with some of the nicest GUI programs and features to get the most out of your configuration. Naze32 rev6 Features: USB on right side PPM/PWM input as through-hole 3.3V, I2C on standard-size headers Fully pinout compatible with rev5 accessories (OSDoge etc) SBUS Inverter Spectrum satellite MPU6500 Sonar pads w/resistors added for direct connection to 5V sonar All extra pads (FT, GP, A5) on top, only sonar on bottom BMP280 barometer 16mbit flash Guide: https://www.dronetrest.com/t/naze-32-revision-6-flight-controller-guide/1605

Guitar pedal starter template based on project by Mark Wu. Includes schematic and PCB layout for basic DIY pedal hardware. This includes two 1/4" jacks (one for input and one for output), a 9V power supply, a 3PDT true bypass wiring setup, and an example potentiometer that can be copy/pasted throughout the circuit. size is a good default size for a 125B enclosure. The headers are meant to be unpopulated so that wires can be soldered to the pads. PCB design rules imported from the JLCPCB 2-layer stackup template. Meant to be used with the 3PDT Breakout Board on my profile. #template

Guitar pedal starter template based on project by Mark Wu. Includes schematic and PCB layout for basic DIY pedal hardware. This includes two 1/4" jacks (one for input and one for output), a 9V power supply, a 3PDT true bypass wiring setup, and an example potentiometer that can be copy/pasted throughout the circuit. size is a good default size for a 125B enclosure. The headers are meant to be unpopulated so that wires can be soldered to the pads. PCB design rules imported from the JLCPCB 2-layer stackup template. Meant to be used with the 3PDT Breakout Board on my profile. #template

Guitar pedal starter template based on project by Mark Wu. Includes schematic and PCB layout for basic DIY pedal hardware. This includes two 1/4" jacks (one for input and one for output), a 9V power supply, a 3PDT true bypass wiring setup, and an example potentiometer that can be copy/pasted throughout the circuit. size is a good default size for a 125B enclosure. The headers are meant to be unpopulated so that wires can be soldered to the pads. PCB design rules imported from the JLCPCB 2-layer stackup template. Meant to be used with the 3PDT Breakout Board on my profile. #template

Guitar pedal starter template based on project by Mark Wu. Includes schematic and PCB layout for basic DIY pedal hardware. This includes two 1/4" jacks (one for input and one for output), a 9V power supply, a 3PDT true bypass wiring setup, and an example potentiometer that can be copy/pasted throughout the circuit. size is a good default size for a 125B enclosure. The headers are meant to be unpopulated so that wires can be soldered to the pads. PCB design rules imported from the JLCPCB 2-layer stackup template. Meant to be used with the 3PDT Breakout Board on my profile. #template

Guitar pedal starter template based on project by Mark Wu. Includes schematic and PCB layout for basic DIY pedal hardware. This includes two 1/4" jacks (one for input and one for output), a 9V power supply, a 3PDT true bypass wiring setup, and an example potentiometer that can be copy/pasted throughout the circuit. size is a good default size for a 125B enclosure. The headers are meant to be unpopulated so that wires can be soldered to the pads. PCB design rules imported from the JLCPCB 2-layer stackup template. Meant to be used with the 3PDT Breakout Board on my profile. #template