Xiao could be a good way to mod your house or machines, with a simple relay controller to rule the wires.

The "Green Dot 2040E5" Board is a Node that interfaces RS485 Sensor probes and can log information to the cloud using LoRa Connectivity. It uses the XIAO RP2040 and the LoRa-E5 (STM32WLE5JC) modules from Seeed Studio to do its magic. It also has amazing power management capabilities (Solar charging, Battery protection, etc) that make it very useful for IoT applications #internetOfThings #smartHomeDevices #SeeedStudio #XIAO #LoRa #RP2040 #IoT

Welcome to your new project. Imagine what you can build here.

Guitar pedal starter template based on project by Mark Wu. Includes schematic and PCB layout for basic DIY pedal hardware. This includes two 1/4" jacks (one for input and one for output), a 9V power supply, a 3PDT true bypass wiring setup, and an example potentiometer that can be copy/pasted throughout the circuit. size is a good default size for a 125B enclosure. The headers are meant to be unpopulated so that wires can be soldered to the pads. PCB design rules imported from the JLCPCB 2-layer stackup template. Meant to be used with the 3PDT Breakout Board on my profile. #template

I want to blow up a MOSFET gloriously. Basically supercapacitor onto MOSFET with a gate flipping setting.

This is a reference design of high efficiency synchronous step-down dc-dc converters optimized for battery powered portable applications. #power #dcdc #ti #buck #referenceDesign #powermanagement #texas-instruments #template #reference-design

Welcome to your new project. Imagine what you can build here.

Mixed Voltage Arduino Nano Integration Example on a 4 Layer PCB Changelog/TODO: -Breakout the SPI Bus in a 2.54mm header in a snap off manner -add an IMU -Reorder the rows of the LEDs Tutorials: https://circuitdigest.com/microcontroller-projects/interfacing-max7219-led-dot-matrix-display-with-arduino

This bee hotel version is an intermediary version that implements some featuresets. The main feature that we are leaving out is Matter support over Zigbee (for a wider range in the backyard). In this version, we are implmenting: -Legacy WiFi/BT connectivity. -Camera with flash capability -Solar Charging -Energy Storage -Humidity and Temp Sensor

Change History from V1: -13.56MHz tuning -larger instruction font -put some stuff on the back #template I wanted to create a business card that has some functionality and shows off a bit of my portfolio IRL: -NFC to my flux page -here's the [instructables](https://www.instructables.com/PCB-Business-Card-With-NFC-Make-Yours-With-NFC-QR-/) -Put a bunch of modules on it Find the BoM [here](https://www.digikey.com/short/2db2vnmp)

Template for Arduino Uno R3 Shield. Include an official pinout so you will always know Arduino names, the alternative roles of pins, which one is SDA, or SCL, etc. On PCB you can find the 3D model of the Arduino Uno R3 itself along with the board outline on the silkscreen. #Arduino #Uno #Shield #Template #project-template #project

I want to create a standard interface from my PCBs to my test equipment. My equipment: PSU: Rigol DP832 Scope: Siglent SDS 1202X-E WaveGen: Siglent SDG810 Logic Analyzer: DSLogic Plus 400MHz VNA: NanoVNA V2 6 scope channels (4 1X, 2 10X) 8 Logic Analyzer channels 1 Wavegen channel 4 Power Nets ( 2 pins each) (tie power nets to oscilloscope inputs) #template #testing

The LoST 3296 board features an Low Power STM32, an RFM95 Module for LoRA connectivity and a connector to interface different sensors. You can hook up a UART module, I2C module and a module using the RS485. The board is powered by the USB-C port

A buck boost converter that can be powered from a Li-Ion battery and output 3.3V @ 500mA. Powered by the TPS63051YFFR and in the same package as a standard Adafruit buck converter. Expect to squeeze around 5-10% SoC from a typical Li-Ion battery. Input Voltage Range: 2.5V to 5.5V Assembled at pcbway.com