PCB Design for Focus Drive
Thought for 3 mins 27 sec
Here are the complete net connections applied to your schematic:
Table
| Net | Connections |
|---|---|
| 5V_IN | J4:VBUS, F1:PAD, U2:VIN, FB1:VIN |
| GND | J4:CC1, J4:CC2, D1:C, D1:A, U2:GND, U2:AGND, U2:PGND, IC1:PGND, IC1:AGND, IC2:GND, U3:GND, U5:GND, J6:PIN1, J6:PIN2, U6:GND, Y1:CASE, F1:PAD |
| 3V3 | U2:VOUT1, U2:VOUT2, U3:VDD, U5:VDD, D2801C61:VCC, TXB0108PWR:A1, TXB0108PWR:A2, J5:VCC |
| 1V8 | U2:VOUT3, IC1:VDD_CORE, IC1:VDDIO, IC1:VDDSDRAM |
| UART_DBG | J5:VCC, J5:GND, J5:TXD, J5:RXD, IC1:UART1_RX, IC1:UART1_TX |
| RESET | SW1:COM, IC1:RESET |
| CAM_IF | J2:CLK, J2:D0, J2:D1, J2:D2, J2:D3, J2:SCL, J2:SDA, IC1:CSI_CLK, IC1:CSI_D0, IC1:CSI_D1, IC1:CSI_D2, IC1:CSI_D3, IC1:CSI_SCL, IC1:CSI_SDA |
| IR_PORT | J6:PIN1, J6:PIN2, J6:PIN3, J6:PIN4 |
| SPEAKER | FB1:SP+, FB1:SP– |
| BT_UART | U6:TXD, U6:RXD, TXB0108PWR:A3, TXB0108PWR:B3, TXB0108PWR:A4, TXB0108PWR:B4 |
| SIM_UART | U5:TXD, U5:RXD, TXB0108PWR:A5, TXB0108PWR:B5, TXB0108PWR:A6, TXB0108PWR:B6 |
| I2C_BUS | U6:SCL, U6:SDA, R_pu1:PIN1, R_pu2:PIN1 |
| GPS_UART | U3:TXD, U3:RXD |
All nets are now wired. Let me know if you’d like to run an ERC/DRC next!
No stock data available for H1.
Details
Designator Stock MPN Lifecycle Status
H1 — MountingHole_Pad —
D1
0
J4
0
U2
0
U5
0
H1
—
J2. these parts rent available place hmem and get parts that are available
Thought for 1 min 57 sec
I can update the parts list by removing the out-of-stock items and inserting stocked replacements:
Parts to remove:
Parts to add:
- USBLC6-2P6 (TVS diode for USB-C ESD protection)
- TYPE-C-6M-006 (USB-C receptacle, 5 V/3 A)
- MCP1700-3302E/TO (3.3 V LDO regulator, 250 mA)
- M95FA-03-STDN (GPRS modem module)
- BM04B-SRSS-TB (JST SH 1×4 connector for IR port)
- MountingHole 2.5 mm Pad (M2.5 mounting holes × 4)
