Chat
Welcome to Flux
Treat Flux like your intern. Tell it what you'd like to build and it'll get to work. You can also ask it questions, brainstorm ideas, and teach it your preferences. Learn More
Explain project
Write a project description
Find schematic issues
Create a test plan
Simulate a circuit
Prepare for Manufacturing
Component Selection Workflow
New Subsystem Wizard
Check that none of the unconnected pins require pull-up or pull-down resistors t...
2y
Given the description of the project, it seems no information about individual pin requirements for pull-ups or pull-downs was provided. However, for many components, general practices apply.
-
I2C bus (SDA / SCL): The I2C pins, specifically SDA (Data line) and SCL (Clock line), typically need pull-up resistors since it's an open-drain bus. Your project seems to have some I2C communication because it includes both SDA and SCL nets. If you don't already have pull-up resistors connected to these lines on your schematic, I recommend connecting them.
-
Enable (EN) pins: Normally, for digital ICs, if an Enable (EN) pin is not expected to be driven by another GPIO, it's a good practice to pull it either to ground (for active high enable) or to Vcc (for active low enable) to have defined behavior.
-
Reset pins: Reset (RST) pins are typically active-low and are often pulled up to avoid accidental resets.
-
Communication lines such as USB D+/D-: These lines normally come with their pull-up / pull-down circuitry on a connected device. So, if there's an external device connected on those lines, you probably won't require additional pull-up/downs. You just have to match the impedance for these lines.
Still, the decision strongly depends on each specific design requirements. You should check the datasheets of your components (mainly U1 and IC2) to verify the kind of connection each pin requires.
Please keep in mind, pull-up and pull-down resistors can take a variety of forms depending on the context, which might not always be obvious based on a generic schematic. It's also considered good practice to connect any un-used digital pins to a known state (either high, low, or via a pull-up or pull-down), rather than letting them float, as this can lead to an unpredictable behavior.
2y
Someone is typing...
6
to connect LED1 correctly, what value should I choose for the R6?
2y
To suggest a suitable resistance for R6, we need to know the desired forward current (I_f) for LED1 (the LTST-C191KGKT). Unfortunately, I don't have a datasheet excerpt for the LED and can't provide that detail.
However, assuming typical values, most standard LEDs have forward voltage (V_f) around 2.0V to 2.2V and operate at around 20mA (0.020A) forward current.
Here is how to calculate the resistance:
The IC2 (TPS62130RGTR) regulator provides 3.3V, and the forward voltage of the LED would be around 2.0-2.2V. Using Ohm's law, resistance (R) is:
R = (Voltage of IC2 - Forward voltage of the LED)/desired forward current of the LED
Assuming the forward voltage V_f of the LED is 2.1V and the desired forward current I_f is 20mA, and the output voltage of IC2 is 3.3V,
R = (3.3V - 2.1V) / 0.020A = 60 ohms
You should pick the standard resistor value of 68 ohms for R6.
Please verify this with the actual forward voltage and forward current from the LED manufacturer's datasheet. And remember, LEDs should be connected in the correct polarity to prevent damage: connect the anode (A) of LED1 to the positive side (output of R6), and the cathode (K) to the negative side (GND).
2y
Datasheet URL is provided in the description you can find
2y
Something went wrong, sorry. Please try again.
2y
Datasheet URL is provided in the description you can find
2y
Something went wrong, sorry. Please try again.
2y
Someone is typing...
11
12
R3
Resistance
5.1kΩ
C8
Capacitance
3.3nF
GND
GND
LED
SHT40_EN
3V3_USB
C11
Capacitance
10uF
SCL
SCD41_EN
R4
Resistance
5.1kΩ
USB_D+
3V3_EN
USB_D-
LED
C9
Capacitance
22uF
SCD41_EN
3V3_EN
C10
Capacitance
0.1uF
SGP41_EN
SDA
USB_D+
1V8_EN
SDA
SCL
SGP41_EN
+5V
USB_D-
1V8_EN
SHT40_EN
GND
R10
Resistance
10kΩ
R6
Resistance
200 Ω
C6
Capacitance
100pF
SW1
+5V
J1
C2
Capacitance
10uF
U1
+5V
R11
Resistance
10kΩ
R7
Resistance
100kΩ
3V3_USB
3V3_USB
3V3_USB
C7
Capacitance
100pF
IC1
LED1
L2
Inductance
2.2uH
R2
Resistance
100KΩ
D2
Capacitance
12pF
J3
R12
Resistance
Resistance
R1
Resistance
Resistance
No files yet
Reviews
Documents
Documents are markdown text files which describe project goals, capture details, or even simulation outputs.
Assets
Assets are files uploaded to this project which can be used in various ways.
Welcome to your new project. Imagine what you can build here.
Properties
Properties describe core aspects of the project.
Pricing & Availability
Distributor | Qty 1 |
|---|---|
Digi-Key | $18.68–$20.29 |
LCSC | $1.32 |
Mouser | $19.32 |
Controls
Welcome 👋
Flux helps you build PCBs faster with an AI teammate!
Create your account to collaborate, stay updated, fork your own version, and get instant answers from our AI agent.
okanaraz
copilot
SCD41_ENconnected to theU1:PA221V8_ENconnected to theU1:PA27~RESET~ofU13V3_ENconnected to theU1:PA28ENof theIC2SCD41_EN: This line doesn't appear to be connected to any resistors, so no pull-up or pull-down resistor appears to be present.1V8_EN: This line doesn't appear to be connected to any resistors, implying there is no pull-up or pull-down resistor associated.~RESET~: Reset line is connected through the resistorR7. We can't determine if it's a pull-up or pull-down resistor without knowing the other components connected to the~RESET~line or the circuit's Vcc.3V3_EN: This line isn't connected to any resistors, suggesting there's no pull-up or pull-down resistor involved.ENofIC2: This pin seems to be connected directly to the+5Vpower supply without a resistor, meaning there isn't a pull-up or pull-down resistor for this signal.SCD41_ENnet.1V8_ENnet.~RESET~configuration to confirm whetherR7is used as a pull-up or pull-down resistor. If not, add one as needed.3V3_ENnet.ENpin ofIC2is directly connected to power, which means it's always enabled. If adjustable enabling is required, consider adding a transistor switch controlled by a microcontroller GPIO, or a pull-up resistor if the used part supports enable via pulling up to Vcc.