Smart Irrigation Controller Design


  • Connected U1:IO13, R1:P1 to ^THERMALINK_IR_TX_CTRL
  • Connected R1:P2, Q1:B to ^THERMALINK_IR_TX_BASE
  • Connected U1:5V, J1:1, R2:P1 to ^Net 1
  • Connected R2:P2, LED1:A to ^THERMALINK_IR_LED_A
  • Connected U1:IO33, SW2:1-1, SW2:1-2, R12:P1, C13:P1 to ^THERMALINK_BTN2
  • Connected SW2:2-1, SW2:2-2, C13:P2, C12:P2, C14:P2 to ^GND
  • Connected R12:P2, U1:3V3, C14:P1 to ^THERMALINK_3V3
  • Connected U1:IO32, C12:P1 to ^THERMALINK_BTN1
nets {
net THERMALINK_3V3 = U2:1, C14:P1, U1:3V3, R12:P2, R10:P2, U3:V+, R11:P2;
net THERMALINK_PIR_OUT = U1:IO27, J1:2;
net GND = C12 P2 - U2 GND:GND, SW2 2-2 - C13 P2:GND, C14:P2, C12:P2, C13:P2, SW2:2-2, SW2:2-1, SW1 2-2 - C12 P2:GND, SW1:2-2, SW1:2-1, U2:3, U1 GND - Q1 E:GND, U1:26, U1:20, U1:14, Q1:E, U3:GND, U1 GND - U1 GND:GND, J1:3;
net THERMALINK_BTN1 = SW1:1-1, C12:P1, U1:IO32, SW1:1-2, R11:P1;
net THERMALINK_DHT22_DATA = U2:2, U1:IO14, R10:P1;
net THERMALINK_IR_RX_OUT = U3:OUT, U1:IO25;
net THERMALINK_IR_TX_LED_K = Q1:C, LED1:K;
net THERMALINK_IR_TX_CTRL = U1:IO13, R1:P1;
net THERMALINK_IR_TX_BASE = R1:P2, Q1:B;
net Net 1 = U1:5V, R2:P1, J1:1;
net THERMALINK_IR_LED_A = R2:P2, LED1:A;
net THERMALINK_BTN2 = U1:IO33, SW2:1-1, SW2:1-2, C13:P1, R12:P1;
}
Set the trace width for the nets GND, THERMALINK_3V3, and Net 1 to 0.5mm. Set the trace width for all other signal and GPIO nets to 0.25mm. Apply these rules to the PCB layout and update the airwires to reflect the different widths.
Listo.
Reglas aplicadas en PCB

Table


ReglaValor
Potencia: GND, THERMALINK_3V3, Net 10.5 mm
Señales / GPIO por defecto0.25 mm
Estado actual
  • La regla Power_Nets quedó en 0.5 mm para las redes de alimentación.
  • La regla general de trazas quedó en 0.25 mm para el resto de señales.
Nota sobre airwires
Los airwires reflejan conectividad, no grosor de pista. Así que:
  • sí quedan actualizados con las conexiones nuevas
  • pero no cambian visualmente de ancho por estas reglas hasta que enrutes trazas reales
Si quieres, el siguiente paso útil es revisar el listado de nets y confirmar que:
  • Net 1 sigue siendo tu red de 5V
  • no hay ninguna red de potencia adicional que también deba ir a 0.5 mm
Verifica Net 1
Chequea reglas PCB
Lista nets anchas