Conception Carte Électronique Simplifiée

Oui. Pour une version éducative simplifiée, je structurerais le schéma en 5 blocs : alimentation, CPU/SoC, mémoire, interfaces rapides, et GPIO/extension.

Diagram


"USB-C node_5V Input" "Power Tree\n5V, node_3V3, node_1V8" "CPU Block\nBCM2711 symbolic SoC" "LPDDR4 RAM Block\n16 GB symbolic pads" "Interfaces\nHDMI, USB3, GbE, microSD" "40 Pin GPIO Header"
Répartition recommandée :
  1. Bloc alimentation
    • USB-C 5 V / 3 A
    • Protection d’entrée : fusible ou eFuse, TVS, condensateurs bulk
    • Régulateur buck 5 V -> 3.3 V
    • Régulateur 3.3 V ou 5 V -> 1.8 V
    • Nets principaux : 5V, 3V3, 1V8, GND
  2. Bloc CPU / SoC
    • BCM2711 ou symbole simplifié équivalent
    • Découplage dense : 100 nF par broche d’alim symbolique + quelques 10 uF
    • Signaux sortants groupés par interface : HDMI, USB, Ethernet, SDIO, GPIO, RAM
    • Ajouter des broches symboliques plutôt qu’un vrai BGA complet si l’objectif est éducatif
  3. Bloc mémoire
    • 16 Go LPDDR4 représentés symboliquement
    • Pads ou empreinte BGA mémoire
    • Signaux groupés : DDR_DQ, DDR_ADDR, DDR_CLK, DDR_CTRL
    • Ne pas router en détail ; indiquer en sérigraphie ou note : “DDR4 symbolic, not length matched”
  4. Bloc interfaces
    • HDMI : HDMI_TX0/1/2/CLK, HDMI_HPD, HDMI_SCL, HDMI_SDA
    • USB 3.0 : USB_D+, USB_D-, USB_SSTX/RX
    • Ethernet Gigabit : idéalement via PHY + RJ45 magnétique, ou bloc symbolique simplifié
    • microSD : SD_CLK, SD_CMD, SD_D0..D3
    • Prévoir ESD sur HDMI, USB, Ethernet, microSD
  5. Bloc GPIO 40 broches
    • Compatible Raspberry Pi : 5V, 3V3, GND, GPIO, I2C, SPI, UART, PWM
    • Ajouter une note claire : “GPIO educational mapping, not guaranteed BCM2711 exact pinout”
Pour l’alimentation, je te conseille de faire un budget de courant simplifié avant de choisir les régulateurs : avec USB-C 5 V / 3 A, vise au moins 3 A sur le chemin 5 V, puis dimensionne le buck 3.3 V autour de 1.5 A à 2 A minimum pour rester cohérent avec une carte type SBC éducative.
Budget de courant
Définir connecteurs
Choisir régulateurs
Documenter architecture
Liste de nets

To get started, talk to Flux or create a New Document.

Documents

    Documents are markdown text files which describe project goals, capture details, or even simulation outputs.

    Assets

    Screen Shot 2022-11-10 at 8.46.37 PM.png

    Screen Shot 2022-11-10 at 8.46.37 PM.png

    Screen Shot 2022-11-10 at 8.46.37 PMThumbnail

    raspberry-pi-2-3-4-model-b-template

    raspberry-pi-2-3-4-model-b-template thumbnail
    Raspberry Pi 2, 3, 4 or 400 Model B+ connector with RPi board outline and mounting holes. good for Raspberry Pi Shield projects. Insulation Height 0.335" (8.51mm) Compatible part number: PPPC202LFBN-RC #RaspberryPi #HAT #RPi #template #project

    Properties

    Properties describe core aspects of the project.

    Pricing & Availability

    Distributor

    Qty 1

    Arrow

    $13.47

    Digi-Key

    $14.15

    LCSC

    $0.52

    Mouser

    $13.99

    Verical

    $13.47

    Controls