Schematic Update Instructions

flux

0:00

Work done
  • None of the planned tasks were completed.
Tasks not done
  • Update project description to reflect J1A/J1B and 6 V rail splitting
  • Update system architecture mermaid diagram with J1A/J1B, BankA_6V, BankB_6V
  • Add mirrored 2×10 right-angle IDC headers and configure GND pins
  • Remap CH1–CH32 from U1/U2 to new headers
  • Split rails: rename U7.OUT→BankA_6V (with C6), U8.OUT→BankB_6V (with C7)
  • Validate full power path (BAT→J2→U6→U7/U8→banks)
  • Sync schematic to PCB layout
  • Update BOM (remove old, add headers)
  • Run ERC and DRC
  • Add “Pin Mapping Report” project property
Tasks I cannot do for you
  • Sever all net connections from J1 pins
  • Remove component symbol and footprint of J1
  • Add two mirrored IDC headers (MPN 3020-20-0200-00) as J1A and J1B (IDC Header 2×10 RA)
  • Wire pins 5, 10, 15, and 20 of both headers to GND
  • Remove J1 entry from the BOM
Success criteria
  • None of the success criteria have been met.
Recommended next step Decide on how to handle the connector removal and header addition. If you’d like me to proceed with schematic edits you can perform, please confirm or provide guidance on outsourcing those tasks.
85 days
Sign up to send

To get started, talk to Flux or create a New Document.

Documents

    Documents are markdown text files which describe project goals, capture details, or even simulation outputs.

    Assets

    No assets added.

    Traditional Bronze Jetpack

    Traditional Bronze Jetpack thumbnail
    Two-Bank 6 V Igniter Firing System with Onboard 2S LiFePO4 Pack, S-8252A Protection, BQ24618 LiFePO4 Charger (3 A, 3.6 V Fast, <50 mA Termination, 3.8 V HPPC, 3.5 V Float), 32 SOT-223 MOSFET Outputs via MCP23017, with Reserved PCB Areas for Dual 26650 Holders, 34-pin IDC, and Barrel Jack Input #LiFePO4 #Battery #BMS

    Properties

    Two-bank 6 V igniter firing system with independent eFuse protection and low-droop power path, controlled by ESP32-S3 with GPIO expansion for multiple ignition channels.

    5

    %

    2S LiFePO4 pack with S-8252A protection, BQ24618 charger, TPS54821 6 V buck feeding dual TPS25982 eFuse banks, each with bulk capacitance sized to support up to 6 A with ≤0.10 V droop over a 1 s pulse, and brought out to a 34-pin IDC connector; ESP32-S3 and dual MCP23017 expanders powered from MP1584 3.3 V buck for control of two independent igniter banks.

    5

    %

    LCSC

    4 positions × 4 igniters per side; channels 1–16 in Bank A; 17–32 in Bank B

    monthly

    Battery

    ti.com/lit/ds/symlink/bq24618.pdf

    10000

    hours

    solderpad.org/licenses/SHL-2.1/

    Arduino

    WiFi

    Energy

    flowchart TD H1["26650 Holder 1"] --> H2["26650 Holder 2"] H2 --> P1["S-8252A Protector"] P1 --> P2["BQ24618 Charger"] P2 --> P3["TPS54821 6V Buck"] P3 --> F1["TPS25982 eFuse Bank A"] P3 --> F2["TPS25982 eFuse Bank B"] F1 --> J1["34-pin IDC Connector"] F2 --> J1 subgraph Control U1["MP1584 3.3V Buck"] --> U2["ESP32-S3"] U2 --> U3["MCP23017 Expander 1"] U2 --> U4["MCP23017 Expander 2"] end

    25

    Pricing & Availability

    Distributor

    Qty 1

    Arrow

    $71.02–$76.58

    Digi-Key

    $30.44–$864.48

    LCSC

    $39.51–$44.12

    Mouser

    $43.99–$916.29

    TME

    $23.29

    Verical

    $218.43–$242.79

    Controls