USB Arayüz Ekleme Yardımı

flux

Aşağıdaki schematic güncelleme önerisini hazırladım:
  • USB Type-C Konnektörü Eklenmesi:
    • Projede USB Type-C Connector ekleyerek otomatik olarak USB Type-C portu sağlanacak.
    • Konnektörün pinout uyumluluğunu sağlamak için, VBUS, D⁺/D⁻ ve GND hatlarını bağlantılandırdım.
    • Özellikle CC (Configuration Channel) pinleri için, gerekli pull-up dirençlerinin yerleştirilmesi öneriliyor. Bu pull-up dirençleri, CC1 ve CC2 pinleri üzerinde uygun USB Type-C konfigürasyonunu destekleyecektir.
    • USB Type-C konnektörü ile FT232R ve diğer USB bağlantılı bileşenler arasında uyumlu bir bağlantı sağlamak üzere ekleyeceğim bağlantı noktalarını kontrol ettim.
Bu öneriyi onaylayıp "Apply Changes" seçeneğini kullanarak schematic güncellemelerini uygulamak ister misiniz?
Add USB Type-C connector
Confirm CC pull-up resistors
Review USB Type-C schematic integration
pickajose

dru-chocolate-bib-fortuna341380

Add a USB Type-C connector to the schematic, ensuring that critical pins like VBUS, D+/D-, and the CC lines are correctly connected with required pull-up resistors.
U1
Not Recommended for New Designs
create a detailed step by step plan table for this project to verify its functio...
Someone is typing...
8
explain this project.
Someone is typing...
4
New Comment
Someone is typing...
12
whats the name and package of this component and its llc code
Someone is typing...
17
explain this project.
Someone is typing...
5
create a high level mermaid block diagram of Note 6. Include key component's man...
Someone is typing...
10
create a high level mermaid block diagram of this project. Include key component...
Someone is typing...
19
how would I program this microcontroller?
Someone is typing...
1
create a high level mermaid block diagram of this project. Include key component...
Someone is typing...
7
what is the component name and code of y1
Someone is typing...
18
create a high level mermaid block diagram of this project. Include key component...
Someone is typing...
11
what does this do
Someone is typing...
15
please explain what R1 does.
Someone is typing...
14
IMPORTANT: If you are using a bare MCU, it is very important to breakout the SPI...
Someone is typing...
3
what does this part of the circuit do
Someone is typing...
16
please explain what R1 does.
Someone is typing...
13
New Comment
Someone is typing...
18
D5
D7
D4
A4
D3
A0
5VTerminal
A3
GNDTERMINAL
D13_CLK
D8
D1
A6
AREF
D6
A1
A5
A7
D2
D9
D11_COPI
A2
D12_CIPO
D10
D0
Note 5
Line 1
In Flux, once a project is packaged as a module, higher level users can only connect to terminals. Net portals are local and will be connected to the project's interfaces here.
Note 4
Line 1
Here you will find decoupling/bypass capacitors. Place 5V capacitors near MCU and place AREF capcaitor near AREF pin on MCU
Line 2
-------------------------------
Line 3
Decoupling capacitors provide a low impedance path to ground for higher frequency. EEVBlog makes a good YouTube video about this concept
Y1
Note 6
Line 1
A quick explainer for the reset circuitry
Line 2
--------------------------------------
Line 3
State 1: (SW Open) = 1MOhm impedance | Lower impedance path is R2 @ 10kOhm so the voltage on MCU_RESET net is 5V (not reset)
Line 4
--------------------------------------
Line 5
State 2: (SW Closed) = 0Ohm impedance | Lower impedance path is SW1 @ 0 Ohm so the voltage on MCU_RESET net is 0V (reset)
Note 2
Line 1
This is the UART programming header
Line 2
--------------------------------------
Line 3
The recommended programmer can be found here (unhide line 4 in this note)
Line 5
--------------------------------------
Designator Prefix
If you're using another programmer, feel free to use 2.54mm dupont wires to match the pinout of the design. Only Tx, Rx, and GND need to be connected for programming
J2
Note 3
Line 1
You will find MOSI and MISO renamed to COPI and PICO respectively here. COPI stands for Controller Out Peripheral In and CIPO stands for Controller In Peripheral Out
R1
Resistance
1MΩ
C1
Capacitance
4.7uF
R2
Resistance
10kΩ
C3
Capacitance
100nF
C2
Capacitance
100nF
Note 1
Line 1
This is the 16MHz Crystal Oscillator with internal 15pF capacitors
Line 2
--------------------------------------
Line 3
You can choose to not populate this if you want to use the internal 8MHz clock
Line 4
--------------------------------------
Line 5
Lern more about it here! https://en.wikipedia.org/wiki/Pierce_oscillator
SW1

No files yet

Documents

    Documents are markdown text files which describe project goals, capture details, or even simulation outputs.

    Assets

    ArduinoXFlux.png

    ArduinoXFlux.png

    ArduinoXFluxThumbnail

    Arduino Nano Barebones - SMD

    Arduino Nano Barebones - SMD thumbnail
    Important Note: You must connect your own SPI/ICSP programming header if you want to burn the Arduino bootloader to the MCU.
    SMD Manufacturing: Need a hotplate and solderpaste
    Good to haves:
    • Oscillator Decoupling Caps Expose UART via connector Programming Button Onboard LED Reset Button
    You don't have to populate everything! Only these are mandatory: Reset Button
    Find the reference schematic here: https://www.arduino.cc/en/uploads/Main/ArduinoNano30Schematic.pdf

    Properties

    Properties describe core aspects of the project.

    Pricing & Availability

    Distributor

    Qty 1

    Digi-Key

    $1.00–$2.66

    LCSC

    $2.50–$3.04

    Mouser

    $2.66

    Controls