Flux Product Design Workflow

H

hacknolix

Briefly describe what it's like to design a complete product in Flux. Help me understand what the PCB-first and enclosure-first design workflows are like to work with.

flux

Designing a complete product in Flux is an iterative workflow where the electronics, PCB layout, firmware, and mechanical enclosure stay in one project and are refined together.
  • PCB-first: Define requirements → design and verify the schematic → size, place, and route the PCB → build the enclosure around the finished board. This is best when electrical performance, connector placement, antenna clearance, or board cost drives the product.
  • Enclosure-first: Define how the product is held, mounted, and used → establish the enclosure, controls, ports, and internal envelope → design the PCB to fit those mechanical constraints. This is best for wearables, handheld products, tightly packaged devices, and products with a strong industrial-design target.
In both workflows, Flux can help select parts, capture and review the circuit, lay out the board, create parametric enclosure geometry, check physical fit, prepare firmware and bring-up documentation, and generate manufacturing outputs. You move through explicit checkpoints rather than treating the PCB and enclosure as independent artifacts.
No project changes were made in this session. Execution stopped because your ACUs ran out.
Sign up to send

Files

Schematic

Layout

3D View

Software & Tools
Everything you need to flash, run, and manage the ESP32 x86 PC Emulator, organized by purpose and operating system. Electronics design tooling is not listed here — that's Flux.ai, where you're already reading this.
Required — for flashing the firmware
These are needed to compile and upload the firmware to the board.

Table

ToolPurposeDownload
Arduino IDECompiles and uploads the firmwarearduino.cc/en/software
Arduino-ESP32 core 2.0.17ESP32 board support (install via Boards Manager — see Flashing guide)github.com/espressif/arduino-esp32
FabGL libraryThe emulator core (install via Library Manager)github.com/fdivitto/FabGL
USB-UART driver (CH340C)
The board uses a CH340C USB-to-serial chip. Most modern systems detect it automatically, but if no port appears, install the official driver from WCH:

Table

OSDownload
Windowswch.cn/downloads/CH341SER_EXE.html
macOSwch.cn/downloads/CH341SER_MAC_ZIP.html
LinuxBuilt into the kernel — no download needed
Required — for the SD card
The board boots from a FAT32-formatted microSD card.

Table

OSToolNotes / Download
WindowsBuilt-in formatter, or SD Card FormatterFor cards larger than 32GB, use the official SD Memory Card Formatter to force a single FAT32 partition
macOSDisk UtilityBuilt in — choose MS-DOS (FAT)
Linuxmkfs.fatsudo mkfs.fat -F 32 /dev/sdX (part of dosfstools)
Optional — disk image editors (add your own software to .img files)
To copy DOS programs and games into an existing floppy or hard disk image, mount the .img file on your computer, drag files in, then copy the image back to the SD card.
Windows

Table

ToolBest forDownload
OSFMountMounting HDD .img files (with partitions) as a drive letter, read/writeosforensics.com/tools/mount-disk-images.html
WinImageFloppy .img files — inject/extract files, create blank imageswinimage.com
AIM ToolkitMounting all image types as drives (successor to ImDisk Toolkit)sourceforge.net/projects/aim-toolkit
macOS

Table

ToolBest forNotes
hdiutilMounting raw .img filesBuilt into macOS: hdiutil attach -imagekey diskimage-class=CRawDiskImage file.img
FUSE for macOS + fuse-fatRead/write FAT access to mounted imagesmacfuse.github.io
Linux

Table

ToolBest forNotes
mount (loop device)Mounting .img files directlyBuilt in: sudo mount -o loop,offset= file.img /mnt/point
mtoolsReading/writing FAT images without mountingmcopy -i file.img game.exe ::/ — part of the mtools package
GNOME DisksGraphical mounting and partition viewingUsually preinstalled on desktop distros
Where to get operating systems & software
All legal and free.

Table

SourceWhat's there
FabGL download libraryReady-to-use OS images (FreeDOS, MS-DOS, Windows 3.0, GEM, GEOS, CP/M-86, ELKS) — downloaded automatically on first boot
FreeDOSFree, open DOS — full OS plus bundled utilities and tools
SvarDOSLightweight free DOS distribution with an online package repository
Internet Archive — MS-DOS SoftwareThousands of preserved DOS games and applications
Internet Archive — MS-DOS GamesCurated classic game collection
A note on compatibility
This is an XT-class machine (8086/8088 CPU, CGA/Hercules graphics, 640KB RAM). Stick to 1981–1991 era software for the best results. Programs requiring a 286/386+ CPU, EGA/VGA graphics, or more than 640KB of memory will not run.
A good first install: Norton Commander — a dual-pane file manager that makes navigating DOS far easier than typing commands.

  • Required — for flashing the firmware

  • USB-UART driver (CH340C)

  • Required — for the SD card

  • Optional — disk image editors (add your own software to `.img` files)

  • Windows

  • macOS

  • Linux

  • Where to get operating systems & software

  • A note on compatibility