Part Information Review and Update


I reviewed the current part project and cross-checked it against both the existing Adafruit document and the official Bosch BMP280 sensor datasheet.
Overall result
  • Datasheet URL is already set, so I did not overwrite it. Per the project, it points to the Adafruit breakout guide, not the Bosch sensor datasheet.
  • The current part project is modeling the Adafruit breakout board, not the bare Bosch sensor IC.
  • The symbol/pin labels are mostly consistent with the Adafruit board pinout.
  • The main gaps are metadata completeness and missing pin descriptions/properties, plus a footprint abstraction mismatch versus the actual breakout/mechanical data.
The recommended workflow for part-project verification is to treat the datasheet as the source of truth for metadata and exact pin info, and to flag count/package mismatches explicitly rather than guessing
Current project information Project properties

Table


FieldCurrent valueAssessment
Manufacturer Part NumberAdafruit_BMP280Likely usable as an internal/library name, but not a formal Adafruit SKU/MPN
Manufacturer NameAdafruitReasonable
Datasheet URLAdafruit breakout PDFPresent, but this is a guide/breakout document, not the official Bosch IC datasheet
Part TypeSensorsBroad but acceptable
Designator PrefixICNot ideal for a breakout board; more often a module/board would use a different convention
Schematic symbol contents
The project contains 9 terminal-style components:
All of them are currently typed as Terminal with Pin Type = Passive.
Footprint contents
The layout contains pads for:
Datasheet / document cross-check Adafruit breakout guide says
The existing project Datasheet URL points to the Adafruit guide. That document describes the board as an Adafruit BMP280 Barometric Pressure + Temperature Sensor Breakout with:
  • I2C and SPI support
  • VIN = 3 V to 5 V input
  • 3Vo = regulated 3.3 V output, up to 100 mA
  • onboard regulator and level shifting
  • pin meanings:
    • VIN = power input
    • 3Vo = regulator output
    • GND = ground
    • SCK = SPI clock / I2C SCL
    • SDI = SPI MOSI / I2C SDA
    • SDO = SPI MISO
    • CS = SPI chip select
Official Bosch BMP280 datasheet says
The official Bosch BMP280 datasheet identifies the sensor IC as:
  • Bosch Sensortec BMP280
  • 8-pin metal-lid LGA
  • package size 2.0 mm × 2.5 mm × 0.95 mm
  • interfaces: I2C and SPI
  • supply ranges:
    • VDD: 1.71 V to 3.6 V
    • VDDIO: 1.2 V to 3.6 V
  • pressure range: 300 to 1100 hPa
  • operating temperature: -40 °C to +85 °C
  • key IC pins:
    • 1 GND
    • 2 CSB
    • 3 SDI / SDA
    • 4 SCK / SCL
    • 5 SDO / I2C address select
    • 6 VDDIO
    • 7 GND
    • 8 VDD
Key specs summary Breakout-board level

Table


SpecValue
ProductAdafruit BMP280 breakout
FunctionPressure + temperature sensor breakout
Host interfacesI2C, SPI
Board input voltage3 V to 5 V
Logic level handling3 V to 5 V safe via level shifting
Regulated output pin3.3 V, up to 100 mA
User-facing pinsVIN, 3VO, GND, SCK, SDI, SDO, CS
Sensor-IC level

Table


SpecValue
Sensor ICBosch BMP280
Package8-pin LGA metal-lid
Package size2.0 mm × 2.5 mm × 0.95 mm
IC supply1.71 V to 3.6 V
Interface supply1.2 V to 3.6 V
Pressure range300 to 1100 hPa
Operating temperature-40 °C to +85 °C
Mismatches / issues found 1) Datasheet property is present, but not the official sensor datasheet
  • The current property points to the Adafruit breakout guide, not the Bosch datasheet.
  • This is not strictly wrong for a breakout-board part, but it means:
    • good for board pinout
    • weaker for formal IC package/spec verification
Flag: metadata quality issue, not a hard error.
2) MPN is not a precise commercial part number
  • Adafruit_BMP280 looks like a project/library identifier, not a formal manufacturer part number.
  • For a production-quality part entry, I’d expect either:
    • the exact Adafruit breakout SKU/MPN, or
    • a clear statement that this part is a module/breakout, not the Bosch IC.
Flag: likely incomplete metadata.
3) Package / case code is missing
The project does not currently expose a package/case code such as:
  • breakout board form factor / header footprint description, or
  • Bosch IC package if the part is intended to reference the sensor chip.
The sync guidance specifically calls out package/case code as core metadata to verify and populate
Flag: missing metadata.
4) Symbol pin descriptions are missing
The current terminals have designators and pin numbers, but I do not see Pin Description properties such as:
  • VIN = Board power input
  • 3VO = Regulated 3.3 V output
  • SCK = SPI SCK / I2C SCL
  • SDI = SPI MOSI / I2C SDA
  • SDO = SPI MISO / I2C address select on sensor side
  • CS = SPI chip select
The part-sync guidance explicitly recommends short per-pin descriptions and exact pin metadata rather than leaving pins minimally defined
Flag: missing pin descriptions.
5) Pin types are too generic
All pins are currently Passive, but the board-level functions are more specific:
  • VIN: Power In
  • 3VO: Power Out
  • GND: Ground
  • SCK: likely Input or Passive at module boundary
  • SDI: Bi-Directional at I2C use, input in SPI use
  • SDO: Output
  • CS: Input
Because this is a breakout module rather than a bare IC, some ambiguity is expected, but Passive for every terminal loses ERC value.
Flag: functional pin typing is incomplete.
6) Bare-IC datasheet vs breakout symbol/footprint are not 1:1
This is the biggest conceptual issue:
  • The Bosch datasheet is for the 8-pin BMP280 IC
  • The project symbol/footprint represent the Adafruit breakout board with 7 user I/O pins + 2 mounting holes
So:
  • pin count does not match the Bosch IC package
  • footprint does not match the 2.0 mm × 2.5 mm LGA sensor package
  • that is expected if this project is intended to be the breakout board
  • but it should be documented clearly in metadata so users do not confuse the part with the raw sensor IC
Flag: abstraction mismatch, but likely intentional.
7) Mounting holes are represented as terminals
MH1 and MH2 appear as terminal components/pads.
That can work for a part project, but they are not electrical signal pins from the sensor or board interface.
Flag: acceptable if intentional, but they should be clearly labeled as mechanical.
What looks correct Pin names vs Adafruit board docs
These match well:
That aligns with the Adafruit breakout pinout from the current document URL
Recommended cleanup High priority

Table


ItemRecommendation
MPNReplace Adafruit_BMP280 with exact Adafruit SKU/MPN if available
Datasheet strategyKeep Adafruit guide as board reference, but also record the Bosch BMP280 datasheet somewhere in metadata/docs
Package / case codeAdd a clear breakout/module package description
Pin descriptionsAdd short descriptions for all user pins
Pin typesChange from all-Passive to functional types where clear
Medium priority

Table


ItemRecommendation
Designator PrefixConsider whether IC is appropriate for a breakout module
Mounting holesMark/document MH1 and MH2 as mechanical
Bottom line
  • Board pin labels: good
  • Metadata completeness: needs work
  • Pin descriptions: missing
  • Pin typing: too generic
  • Footprint vs Bosch datasheet: not a direct match, but that’s expected if this is meant to be the Adafruit breakout board
  • Current datasheet URL: present, but it references a guide, not the official Bosch IC datasheet
If you want, I can now update the part metadata and pin properties directly:
  • add/fix package and description fields
  • add pin descriptions
  • set better pin types
  • optionally replace or supplement the datasheet URL strategy for this breakout part
Fix metadata and pins
Add Bosch datasheet
Clean mounting holes

Name
Pin #
Type
Section
Pin Group
Orientation
Order
Sub-symbol
VIN
1
Passive
3VO
2
Passive
GND
3
Passive
SCK
4
Passive
SDO
5
Passive
SDI
6
Passive
CS
7
Passive
MH1
MH1
Passive
MH2
MH2
Passive

Adafruit_BMP280