Sensor Board PCB Design in KiCad

flux

0:23

Thought for a moment

I haven’t modified the Flux project yet — the project is still empty with 0 components and 0 nets. Since execution credits are unavailable, I can’t build the schematic/PCB here, but you can follow these KiCad steps to create a basic sensor board.
Steps to design a sensor board PCB in KiCad
  1. Define your requirements
    • Which sensor? Example: temperature, humidity, gas, light, motion.
    • Power input: USB 5 V, battery, or external 3.3 V/5 V.
    • Output/interface: I2C, SPI, UART, analog, or digital GPIO.
    • Board size and connector type.
  2. Create a new KiCad project
    • Open KiCad.
    • Click File → New Project.
    • Name it something like sensor_board.
  3. Draw the schematic Add these blocks:
    • Sensor IC/module
    • Power input connector
    • Voltage regulator if needed, for example 5 V to 3.3 V
    • Decoupling capacitors — small capacitors near IC power pins to reduce noise
    • Pull-up resistors for I2C lines if using I2C
    • Programming/output connector, such as header pins
  4. Choose power system Common beginner-friendly option:
    • Input: 5 V through USB or header
    • Regulator: 3.3 V LDO
    • Capacitors:
      • 10 µF on regulator input
      • 10 µF on regulator output
      • 100 nF near each IC power pin
  5. Wire the sensor Example for an I2C sensor:
    • VCC → 3.3 V
    • GND → GND
    • SDA → connector SDA pin
    • SCL → connector SCL pin
    • SDA pull-up → 4.7 kΩ to 3.3 V
    • SCL pull-up → 4.7 kΩ to 3.3 V
  6. Run Electrical Rules Check
    • In schematic editor, click Inspect → Electrical Rules Checker.
    • Fix unconnected power pins, missing ground symbols, and incorrect net labels.
  7. Assign footprints
    • Open Tools → Assign Footprints.
    • For beginner-friendly assembly, choose larger packages:
      • Resistors/capacitors: 0805 or 0603
      • Header: 2.54 mm through-hole
      • Regulator: SOT-23 or SOT-223 depending on current
  8. Open PCB editor
    • Click Update PCB from Schematic.
    • Import all components into the PCB layout.
  9. Set board outline
    • Draw the PCB edge on the Edge.Cuts layer.
    • Example beginner board size: 30 mm × 30 mm or 40 mm × 30 mm.
  10. Place components
  • Put connectors near board edges.
  • Put the sensor away from heat sources like regulators.
  • Put decoupling capacitors close to the sensor and regulator power pins.
  • Keep I2C traces short and simple.
  1. Route traces
  • Use wider traces for power, for example 0.4–0.6 mm.
  • Signal traces can be around 0.25 mm.
  • Add a GND copper pour on top and/or bottom layer.
  1. Run Design Rules Check
  • Click Inspect → Design Rules Checker.
  • Fix clearance errors, unconnected traces, and footprint issues.
  1. Add labels and mounting holes Add silkscreen labels:
  • VCC
  • GND
  • SDA
  • SCL
  • Sensor name
  • Board revision
  1. Generate manufacturing files
  • Go to File → Fabrication Outputs → Gerbers.
  • Also export:
    • Drill files
    • BOM
    • Pick-and-place file if using assembly service
Simple recommended beginner design
If you want an easy first sensor board, use:
  • Sensor: BME280 temperature/humidity/pressure sensor
  • Interface: I2C
  • Supply: 3.3 V
  • Connector: 4-pin header: VCC, GND, SDA, SCL
  • Pull-ups: 4.7 kΩ on SDA and SCL
  • Decoupling: 100 nF near sensor VCC pin
This is a good beginner PCB because it has few parts and works with Arduino, ESP32, Raspberry Pi, and many microcontrollers.
Choose sensor parts
BME280 schematic checklist
KiCad footprint choices
PCB layout guide
Sign up to send

To get started, talk to Flux or create a New Document.

Documents

    Documents are markdown text files which describe project goals, capture details, or even simulation outputs.

    Assets

    No assets added.

    Victorious Aqua Interocitor

    Victorious Aqua Interocitor thumbnail
    Welcome to your new project. Imagine what you can build here.

    Properties

    Properties describe core aspects of the project.

    Pricing & Availability

    See prices from popular manufacturers for your project.

    Controls