Part Information Review and Verification

Thought for 1 min 19 sec

I reviewed the part metadata, symbol terminals, and footprint against the official Renesas datasheet, using the datasheet as the source of truth as recommended for part-project verification

Summary

The Datasheet URL property is already set, so I did not search the web or change that property.
The part is broadly identified correctly as a Renesas buck-boost IC.
The main metadata mismatch is the package property:
- Project: Package or Case Code = TO
- Datasheet: 10 Ld DFN, 0.5 mm pitch, L10.2.5x2.5
The symbol terminal count matches the datasheet:
- Datasheet: 10 leads + exposed pad
- Project: 11 terminals total, including EPAD
The terminal names and pin numbers match the datasheet.
The biggest symbol-data gap is that all terminals are currently Pin Type: Unspecified and there are no pin descriptions. For a part-project audit, those should be populated from the datasheet rather than left blank

Part information review Project properties vs datasheet

Table

Field	In project	Datasheet / official source	Status
Manufacturer Part Number	RAA2361052GNP#HC5	RAA2361052GNP#HC5	Match
Manufacturer Name	Renesas	Renesas Electronics	Acceptable
Part Type	Integrated Circuits	Ultra-low IQ buck-boost regulator with bypass	Acceptable but generic
Designator Prefix	IC	Not a datasheet mismatch, but nonstandard vs common `U` usage	Not critical
Package or Case Code	TO	10 Ld DFN, 0.5 mm pitch, L10.2.5x2.5	Mismatch
Datasheet URL	Present	Official Renesas page/datasheet available	Match

Key specs

Table

Parameter	Value
Function	Ultra-low IQ buck-boost regulator with bypass
Input voltage	1.8 V to 5.5 V
Output voltage	1.8 V to 5.0 V
Output current	Up to 400 mA
Input quiescent current	130 nA
Peak efficiency	96%
Operating temperature	-40°C to +85°C
Package	10 Ld DFN, 0.5 mm pitch, L10.2.5x2.5
Exposed pad	Yes; must be soldered to GND

Symbol cross-check

Datasheet pinout says:

Table

Pin	Name	Function	Project status
1	EN	Enable input	Match
2	RSVD	Reserved, pull to GND	Match
3	BYPASS	Forced bypass control	Match
4	ILIM	Input current limit reader	Match
5	VSET	Output voltage reader	Match
6	VOUT	Output	Match
7	LX2	Boost switch node	Match
8	GND	Ground	Match
9	LX1	Buck switch node	Match
10	VIN	Input supply	Match
EPAD	EPAD	Exposed pad, connect to GND	Match

Symbol findings

Pin count matches exactly: 11 total items including EPAD, which is the correct way to treat the exposed pad for part verification
Pin names match
Pin numbers match
No extra terminals found
No missing terminals found

Symbol issues flagged

All terminals currently have Pin Type: Unspecified
I do not see Pin Description properties on the terminals
I also do not see richer symbol metadata like Section, Pin Group, or orientation assignments

For an IC-style part, those are incomplete relative to the recommended part-project setup

Footprint cross-check

From the layout:

There is a footprint with pads for all named pins plus EPAD
Pad names present:
- EN, RSVD, BYPASS, ILIM, VSET, VOUT, LX2, GND, LX1, VIN, EPAD

Footprint findings

Pad count matches the datasheet package concept: 10 leads + exposed pad
Pad naming matches the pinout
EPAD is present, which is required by the datasheet

Footprint issue flagged

The project package metadata says TO, which does not match the actual DFN package/fingerprint identity from the datasheet.
This is the clearest footprint/metadata mismatch.

Mismatches and gaps

Table

Item	Issue	Severity
Package or Case Code	`TO` in project vs 10 Ld DFN, L10.2.5x2.5 in datasheet	High
Pin Type properties	All pins are `Unspecified`	Medium
Pin descriptions	Missing	Medium
EPAD handling	Present and correctly broken out	OK
Pin names/numbers	Match datasheet	OK
Datasheet URL	Already set	OK

Bottom line

The part is mostly structurally correct:

correct MPN
correct manufacturer
correct terminal count
correct pin names
correct pin numbering
correct inclusion of EPAD

The two things I’d flag are:

Package metadata is wrong/incomplete (TO should be replaced with the actual DFN package code)
Terminal metadata is incomplete because pin types and descriptions have not been populated from the datasheet

If you want, I can fix the part project next by:

updating Package or Case Code
assigning Pin Type for all 11 terminals
adding short Pin Description text for each pin

Fix package and pins

Set proper DFN package

Flag any footprint issues

Reviews

Generic Inductor
A generic fixed inductor suitable for rapid circuit topology development. The footprint automatically adapts based on the selected package, supporting standard SMD sizes (e.g., 0402, 0603, 0805) as well as well-known inductor packages such as SDR1806, PA4320, SRN6028, and SRR1260. Standard inductor values: 1.0 nH, 10 nH, 100 nH, 1.0 µH, 10 µH, 100 µH, 1.0 mH 1.2 nH, 12 nH, 120 nH, 1.2 µH, 12 µH, 120 µH, 1.2 mH 1.5 nH, 15 nH, 150 nH, 1.5 µH, 15 µH, 150 µH, 1.5 mH 1.8 nH, 18 nH, 180 nH, 1.8 µH, 18 µH, 180 µH, 1.8 mH 2.2 nH, 22 nH, 220 nH, 2.2 µH, 22 µH, 220 µH, 2.2 mH 2.7 nH, 27 nH, 270 nH, 2.7 µH, 27 µH, 270 µH, 2.7 mH 3.3 nH, 33 nH, 330 nH, 3.3 µH, 33 µH, 330 µH, 3.3 mH 3.9 nH, 39 nH, 390 nH, 3.9 µH, 39 µH, 390 µH, 3.9 mH 4.7 nH, 47 nH, 470 nH, 4.7 µH, 47 µH, 470 µH, 4.7 mH 5.6 nH, 56 nH, 560 nH, 5.6 µH, 56 µH, 560 µH, 5.6 mH 6.8 nH, 68 nH, 680 nH, 6.8 µH, 68 µH, 680 µH, 6.8 mH 8.2 nH, 82 nH, 820 nH, 8.2 µH, 82 µH, 820 µH, 8.2 mH #generics #CommonPartsLibrary
jharwinbarrozo
16.4k
Generic Capacitor
A generic fixed capacitor ideal for rapid circuit topology development. You can choose between polarized and non-polarized types, its symbol and the footprint will automatically adapt based on your selection. Supported options include standard SMD sizes for ceramic capacitors (e.g., 0402, 0603, 0805), SMD sizes for aluminum electrolytic capacitors, and through-hole footprints for polarized capacitors. Save precious design time by seamlessly add more information to this part (value, footprint, etc.) as it becomes available. Standard capacitor values: 1.0pF, 10pF, 100pF, 1000pF, 0.01uF, 0.1uF, 1.0uF, 10uF, 100uF, 1000uF, 10000uF 1.1pF, 11pF, 110pF, 1100pF 1.2pF, 12pF, 120pF, 1200pF 1.3pF, 13pF, 130pF, 1300pF 1.5pF, 15pF, 150pF, 1500pF, 0.015uF, 0.15uF, 1.5uF, 15uF, 150uF, 1500uF 1.6pF, 16pF, 160pF, 1600pF 1.8pF, 18pF, 180pF, 1800pF 2.0pF, 20pF, 200pF, 2000pF 2.2pF, 22pF, 220pF, 2200pF, 0.022uF, 0.22uF, 2.2uF, 22uF, 220uF, 2200uF 2.4pF, 24pF, 240pF, 2400pF 2.7pF, 27pF, 270pF, 2700pF 3.0pF, 30pF, 300pF, 3000pF 3.3pF, 33pF, 330pF, 3300pF, 0.033uF, 0.33uF, 3.3uF, 33uF, 330uF, 3300uF 3.6pF, 36pF, 360pF, 3600pF 3.9pF, 39pF, 390pF, 3900pF 4.3pF, 43pF, 430pF, 4300pF 4.7pF, 47pF, 470pF, 4700pF, 0.047uF, 0.47uF, 4.7uF, 47uF, 470uF, 4700uF 5.1pF, 51pF, 510pF, 5100pF 5.6pF, 56pF, 560pF, 5600pF 6.2pF, 62pF, 620pF, 6200pF 6.8pF, 68pF, 680pF, 6800pF, 0.068uF, 0.68uF, 6.8uF, 68uF, 680uF, 6800uF 7.5pF, 75pF, 750pF, 7500pF 8.2pF, 82pF, 820pF, 8200pF 9.1pF, 91pF, 910pF, 9100pF #generics #CommonPartsLibrary
jharwinbarrozo
1.5M
Generic Resistor
A generic fixed resistor ideal for rapid circuit topology development. Its footprint automatically adapts based on the selected package case code—supporting 0402, 0603, 0805, 1203, and many other standard SMD packages, as well as axial horizontal and vertical configurations. Save precious design time by seamlessly add more information to this part (value, footprint, etc.) as it becomes available. Standard resistor values: 1.0 ohm, 10 ohm, 100 ohm, 1.0k ohm, 10k ohm, 100k ohm, 1.0M ohm 1.1 ohm, 11 ohm, 110 ohm, 1.1k ohm, 11k ohm, 110k ohm, 1.1M ohm 1.2 ohm, 12 ohm, 120 ohm, 1.2k ohm, 12k ohm, 120k ohm, 1.2M ohm 1.3 ohm, 13 ohm, 130 ohm, 1.3k ohm, 13k ohm, 130k ohm, 1.3M ohm 1.5 ohm, 15 ohm, 150 ohm, 1.5k ohm, 15k ohm, 150k ohm, 1.5M ohm 1.6 ohm, 16 ohm, 160 ohm, 1.6k ohm, 16k ohm, 160k ohm, 1.6M ohm 1.8 ohm, 18 ohm, 180 ohm, 1.8K ohm, 18k ohm, 180k ohm, 1.8M ohm 2.0 ohm, 20 ohm, 200 ohm, 2.0k ohm, 20k ohm, 200k ohm, 2.0M ohm 2.2 ohm, 22 ohm, 220 ohm, 2.2k ohm, 22k ohm, 220k ohm, 2.2M ohm 2.4 ohm, 24 ohm, 240 ohm, 2.4k ohm, 24k ohm, 240k ohm, 2.4M ohm 2.7 ohm, 27 ohm, 270 ohm, 2.7k ohm, 27k ohm, 270k ohm, 2.7M ohm 3.0 ohm, 30 ohm, 300 ohm, 3.0K ohm, 30K ohm, 300K ohm, 3.0M ohm 3.3 ohm, 33 ohm, 330 ohm, 3.3k ohm, 33k ohm, 330k ohm, 3.3M ohm 3.6 ohm, 36 ohm, 360 ohm, 3.6k ohm, 36k ohm, 360k ohm, 3.6M ohm 3.9 ohm, 39 ohm, 390 ohm, 3.9k ohm, 39k ohm, 390k ohm, 3.9M ohm 4.3 ohm, 43 ohm, 430 ohm, 4.3k ohm, 43K ohm, 430K ohm, 4.3M ohm 4.7 ohm, 47 ohm, 470 ohm, 4.7k ohm, 47k ohm, 470k ohm, 4.7M ohm 5.1 ohm, 51 ohm, 510 ohm, 5.1k ohm, 51k ohm, 510k ohm, 5.1M ohm 5.6 ohm, 56 ohm, 560 ohm, 5.6k ohm, 56k ohm, 560k ohm, 5.6M ohm 6.2 ohm, 62 ohm, 620 ohm, 6.2k ohm, 62K ohm, 620K ohm, 6.2M ohm 6.8 ohm, 68 ohm, 680 ohm, 6.8k ohm, 68k ohm, 680k ohm, 6.8M ohm 7.5 ohm, 75 ohm, 750 ohm, 7.5k ohm, 75k ohm, 750k ohm, 7.5M ohm 8.2 ohm, 82 ohm, 820 ohm, 8.2k ohm, 82k ohm, 820k ohm, 8.2M ohm 9.1 ohm, 91 ohm, 910 ohm, 9.1k ohm, 91k ohm, 910k ohm, 9.1M ohm #generics #CommonPartsLibrary
jharwinbarrozo
1.5M
Ground
A common return path for electric current. Commonly known as ground.
jharwinbarrozo
20.5M
Terminal
An electrical connector acting as reusable interface to a conductor and creating a point where external circuits can be connected.
natarius
Net Portal
Wirelessly connects nets on schematic. Used to organize schematics and separate functional blocks. To wirelessly connect net portals, give them same designator. #portal
jharwinbarrozo
43.0M
RMCF0805JT47K0
General Purpose Thick Film Standard Power and High-Power Chip Resistor 47 kOhms ±5% 0.125W, 1/8W Chip Resistor 0805 (2012 Metric) Automotive AEC-Q200 Thick Film Features: - RMCF – standard power ratings - RMCP – high power ratings - Nickel barrier terminations standard - Power derating from 100% at 70ºC to zero at +155ºC - RoHS compliant, REACH compliant, and halogen free - AEC-Q200 compliant
jharwinbarrozo
1.2M
875105359001
10 µF 16 V Aluminum - Polymer Capacitors Radial, Can - SMD 30mOhm 2000 Hrs @ 105°C #commonpartslibrary #capacitor #aluminumpolymer #radialcan
jharwinbarrozo
1.2M
CTL1206FYW1T
Yellow 595nm LED Indication - Discrete 1.7V 1206 (3216 Metric)
jharwinbarrozo
1.1M
1070TR
Battery Holder (Open) Coin, 20.0mm 1 Cell SMD (SMT) Tab bate or batt #forLedBlink
jharwinbarrozo
700.5k

Project Name

RAA2361052GNP#HC5

Description

Single output buck-boost converter 130nA input quiescent current 96% peak efficiency (VIN = 3.6V; VOUT = 3.3V) Output current: up to 400mA (VIN > 2.5V, VOUT = 3.3V) Input voltage range: 1.8V to 5.5V, supports single-cell Li-ion, 2x or 31.5V AA/AAA batteries Output voltage range: 1.8V to 5.0V Output voltage control using a pin reader (RAA236105) Selectable input current limit DVS with settable slew rate control Selectable forced bypass power saving mode PWM/PFM and buck/bo Input voltage range: 1.8 V to 5.5 V Output voltage range: 1.8 V to 5.0 V (programmable) Output current: up to 400 mA Peak efficiency: up to ~96% Quiescent current (IQ): ~100 nA class (ultra-low power mode) Very low standby consumption (ideal for battery-powered systems) Bypass mode available for near-zero regulation overhead Topology: Synchronous buck-boost converter Can step up or step down voltage automatically Maintains stable output even when input varies above/below output #CommonPartsLibrary #IntegratedCircuit #PowerManagement #Voltage-regulator #Switching-regulator #RAA2361052

Properties

Manufac… Number

RAA2361052GNP#HC5

Manufac…er Name

Renesas

Part Type

Integrated Circuits

Datasheet URL

mouser.com/datasheet/3/1166/1/REN_RAA236100_105_DST_20250124.pdf

Designator Prefix

Package …se Code

License

creativecommons.org/licenses/by/4.0/

Pricing & Availability

See prices from popular manufacturers for your project.

Controls

Welcome 👋

Flux accelerates your PCB design with AI.

Create your account to start using this component and bring your ideas to life.

adrian95 / RAA2361052GNP#HC5

Schematic