• Official datasheet URL added to project property Datasheet URL: https://www.compona.com/static_cache/datenblatt/3308423-CT0915S5L228_1_0.pdf
• Source identifies the part as FCT electronic GmbH / Molex FCT drawing CT09-15S5-L228, Molex manufacturer part number 1731130133.

Text
  1   2   3   4   5
    6   7   8   9   10
 11  12  13  14  15

• Project name: 1731130133
• Description: 1731130133 CONN_CT09-15S5-L228_MOL
• Assets:
  • Footprint asset: CONN_CT09-15S5-L228_MOL.kicad_mod
  • Symbol assets: 1731130133_1_1 and 1731130133_1_2
• BOM: no BOM entries found.
• Project properties updated during this audit:
  • Datasheet URL = official PDF URL above
  • Manufacturer Name = Molex / FCT Electronics
  • Manufacturer Part Number = 1731130133 / CT09-15S5-L228

• A DE-15 high-density female connector should expose 15 signal contacts numbered 1 through 15.
• Mounting/shell hardware may be represented optionally as shield/mount pins if intended to connect to chassis/ground, but the datasheet’s electrical contacts are 15.

• Schematic contains 30 terminal components: two complete duplicated terminal sets, each numbered 1 through 15.
• The two sub-symbol suffixes are 1731130133_1_1 and 1731130133_1_2.
• Every terminal has Pin Type: Unspecified.
• No terminal-level Pin Description values were present.
• The symbol pin positions are duplicated between the two sub-symbols.

• Mismatch: Symbol exposes 30 signal terminals, but datasheet defines 15 contacts.
• Mismatch: Pin descriptions are missing/unspecified for all terminals.
• Likely correction: Use one 15-pin symbol unit for contacts 1–15. If shell/mounting features are electrically modeled, add separate clearly named shield/mount pins rather than duplicating signal contacts.

• 15 signal through-hole pads, numbered 1–15.
• 2 mounting/snap-in holes or bracket pads, consistent with Ø3.18 mm and 25.0 mm center spacing.
• Signal holes should be Ø1.2 mm per datasheet.

• Layout contains the correct-looking signal pad set with pads 1–15 arranged on a 3-row high-density D-sub pattern.
• Layout contains two mount pads labeled 16 and 17.
• Mount pad size is approximately 3.2004 mm, matching the Ø3.18 mm datasheet hole requirement closely.
• Signal pad visible size is approximately 1.4986 mm in the main pad set. The tool output did not expose explicit drill/hole size, so the Ø1.2 mm drill could not be confirmed directly from layout metadata.
• Additional duplicate pad-like nodes for pins 1–15 appear at origin with size approximately 1.6 mm. These appear to correspond to duplicated schematic terminals/sub-symbols, not a clean single footprint pad set.

• Mostly matches: Main footprint pad numbering and mount spacing/features are consistent with the datasheet at a high level.
• Needs confirmation: Signal drill diameter Ø1.2 mm is not visible in the layout readout, so the imported KiCad footprint should be inspected directly to verify drill size.
• Potential mismatch/artifact: Duplicate pad nodes for pins 1–15 at origin suggest symbol/footprint import duplication or extra terminal artifacts. These should be cleaned before using the part in a real PCB design.

1. Remove the duplicate 15-pin symbol unit or consolidate to a single symbol exposing contacts 1–15.
2. Add terminal descriptions such as Contact 1, Contact 2, … Contact 15, with pin type set to Passive/Unspecified as appropriate for a connector.
3. Keep mounting pads 16 and 17 only in the footprint unless there is a deliberate schematic-level shell/shield connection requirement.
4. Verify the KiCad footprint asset has signal hole/drill Ø1.2 mm and mount hole Ø3.18 mm.
5. Optionally add connector properties: Part Type = Connector, Connector Type = High Density D-Sub, Connector Gender = Female, Connector Positions = 15, Connector Rows = 3, Mount = Through Hole, Current Rating = 3 A, Voltage Rating = 125 V, Operating Temperature = -55 °C to +105 °C.